Heavy Duty Balanced Opposed Compressors - Ariel Corporation
Heavy Duty Balanced Opposed Compressors - Ariel Corporation Heavy Duty Balanced Opposed Compressors - Ariel Corporation
FOR MODELS: JGZ AND JGU SECTION 1 - DESIGN SPECIFICATIONS & DATA Normal Cycle Time - Seconds per Cycle Break In Cycle Time - Seconds per Cycle Distribution Block Part Numbers Throw Numbers Increase Pump Stroke - CCW FIGURE 1-5 FORCE FEED LUBRICATOR DATA PLATE - TYPICAL FOUR PUMPS Compressor Auxiliary End Cover Speed Reducer Data Plate Location Data Plate Location - See Figure 1-5 for Plate details Unused Drive Shaft - Keep Safety Covers in Place when Compressor is Running Gerhardt Force Feed Lubricator w/up to four pump capacity - Optional for High Pressure Cylinders For more information on the Gerhardt Lubricator, see the Ariel web site under Vendor Literature FIGURE 1-6 FORCE FEED LUBRICATOR DATA PLATE - TYPICAL GERHARDT PAGE 1 - 10 7/09
FOR MODELS: JGZ AND JGU SECTION 1 - DESIGN SPECIFICATIONS & DATA The Force Feed Lubricator provides oil to the piston rod packing and the compressor pistons. The Lubricator Data Plate gives directions for adjusting the flow of oil. If this plate is missing, please contact Ariel Corporation for a replacement or specific directions, see “Ariel Contact Information:” on page 7-14 for contact information. VVCP Information and Instruction Plates, See Figure 1-8 - Customer Work Order Number, & Hydrostatic test Pressure are stamped near this plate on top of the VVCP body F-XXXXX Frame Serial Number stamped on machined surface above the Mechanical Inspector’s Plate. On drive end throw #2 side Discharge Valve Pocket Identification Plate Cylinder Information Plate, See Figure 1-8 FIGURE 1-7 INFORMATION PLATES - TYPICAL Suction Valve Pocket Identification Plate Serial Number, MAWP, Part Number, Work Order Number, Hydrostatic Test Pressure, Test Date and Tester’s Personal Stamp are stamped on the end of each cylinder (cylinder head mounting surface) Cylinder Information Plates appear on each cylinder. The serial number is also stamped on the end of each cylinder. If any plate is missing, please contact Ariel for a replacement or specific directions. NOTE: USE THE CYLINDER AND FRAME SERIAL NUMBERS IN ALL CORRESPON- DENCE. 7/09 PAGE 1 - 11
- Page 1 and 2: ARIEL Heavy Duty Balanced Opposed C
- Page 3 and 4: FOR MODELS: JGZ AND JGU TABLE OF CO
- Page 5 and 6: FOR MODELS: JGZ AND JGU TABLE OF CO
- Page 7 and 8: FOR MODELS: JGZ AND JGU TABLE OF CO
- Page 9 and 10: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 11 and 12: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 13 and 14: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 15 and 16: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 17: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 21 and 22: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 23 and 24: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 25 and 26: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 27 and 28: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 29 and 30: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 31 and 32: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 33 and 34: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 35 and 36: FOR MODELS: JGZ AND JGU SECTION 1 -
- Page 37 and 38: FOR MODELS: JGZ AND JGU SECTION 2 -
- Page 39 and 40: FOR MODELS: JGZ AND JGU SECTION 2 -
- Page 41 and 42: FOR MODELS: JGZ AND JGU SECTION 2 -
- Page 43 and 44: FOR MODELS: JGZ AND JGU SECTION 2 -
- Page 45 and 46: FOR MODELS: JGZ AND JGU SECTION 2 -
- Page 47 and 48: FOR MODELS: JGZ AND JGU SECTION 2 -
- Page 49 and 50: FOR MODELS: JGZ AND JGU SECTION 2 -
- Page 51 and 52: FOR MODELS: JGZ AND JGU SECTION 3 -
- Page 53 and 54: FOR MODELS: JGZ AND JGU SECTION 3 -
- Page 55 and 56: FOR MODELS: JGZ AND JGU SECTION 3 -
- Page 57 and 58: FOR MODELS: JGZ AND JGU SECTION 3 -
- Page 59 and 60: FOR MODELS: JGZ AND JGU SECTION 3 -
- Page 61 and 62: FOR MODELS: JGZ AND JGU SECTION 3 -
- Page 63 and 64: FOR MODELS: JGZ AND JGU SECTION 3 -
- Page 65 and 66: FOR MODELS: JGZ AND JGU SECTION 3 -
- Page 67 and 68: FOR MODELS: JGZ AND JGU SECTION 4 L
FOR MODELS: JGZ AND JGU SECTION 1 - DESIGN SPECIFICATIONS & DATA<br />
Normal Cycle<br />
Time - Seconds<br />
per Cycle<br />
Break In Cycle<br />
Time - Seconds<br />
per Cycle<br />
Distribution Block<br />
Part Numbers<br />
Throw<br />
Numbers<br />
Increase Pump<br />
Stroke - CCW<br />
FIGURE 1-5 FORCE FEED LUBRICATOR DATA PLATE - TYPICAL FOUR PUMPS<br />
Compressor<br />
Auxiliary End<br />
Cover<br />
Speed<br />
Reducer<br />
Data Plate<br />
Location<br />
Data Plate Location -<br />
See Figure 1-5 for<br />
Plate details<br />
Unused Drive Shaft - Keep<br />
Safety Covers in Place when<br />
Compressor is Running<br />
Gerhardt Force Feed Lubricator w/up to four pump capacity - Optional for High Pressure Cylinders<br />
For more information on the Gerhardt Lubricator, see the <strong>Ariel</strong> web site under Vendor Literature<br />
FIGURE 1-6 FORCE FEED LUBRICATOR DATA PLATE - TYPICAL GERHARDT<br />
PAGE 1 - 10 7/09