The Crafter

Technical Data
Valid for model year 2013
Commercial
Vehicles
The Crafter
Tästä esitteestä löydät Crafter-malliston tekniset tiedot ja mittapiirrokset. Esite on
englanninkielinen.
Tiedot perustuvat kansainväliseen myyntiohjelmaan. Esite saattaa sisältää malleja ja moottoreita,
jotka eivät kuulu Suomen tuontiohjelmaan. Suomeen tuotavat mallit löydät hinnastosta.
Oikeudet muutoksiin pidätetään.
Toukokuu 2013

Information on fuel consumption and CO 2 emissions can be found within the technical data.
Not all combinations of engine, gearbox and auto body design are possible. Please discuss your individual requirements with your Volkswagen Commercial Vehicles dealer. Only your
Volkswagen Commercial Vehicles dealer is able to check the necessary combination requirements as well as verify the accuracy and completeness of data in the purchasing system.
The payloads listed here have been established allowing for factory options or other tailored solutions that are not included in the standard scope of delivery and services. The actual
payload of a vehicle, which is calculated by the difference between the gross vehicle weight and the curb weight, can only be established by weighing the individual vehicle.
The product name Caddy ® is a registered brand name of Caddie S.A. and is used by Volkswagen Commercial Vehicles with the kind approval of Caddie S.A.
TDI ® , DSG ® , Shiftmatic ® , 4MOTION ® and BlueMotion ® are registered brand names of Volkswagen AG and other companies in the Volkswagen Group in Germany as well as in other
countries. The fact that a brand name in this document is not marked with ® does not mean that it is not a registered brand name and/or that this brand name may be used without
the written approval of the Volkswagen AG. Not all brand names mentioned are necessarily a part of these technical details.
Our vehicles are equipped with summer tyres as standard. As of the 12.04.2010, in the Federal Republic of Germany you are legally oblieged to equipe your vehicle in icy conditions,
packed snow, slash, ice or hoar frost with winter tyres or all seasons tyres. Please contact your Volkswagen Commercial Vehicles dealer for assistance.
Take-back and recycling of end of life vehicles:
Volkswagen meets the challenges of modern society and takes them into consideration in all new products of the Volkswagen brand. This naturally also applies to protection of the
environment and resources. All new Volkswagens can therefore be recycled in an environment-friendly way and can be returned free of charge, subject to fulfilment of national
legislation. For details concerning take-back and recycling of end of life vehicles, please contact your local Volkswagen dealer, refer to the Internet on www.volkswagen.de or call the
hotline +49 800 - Volkswagen (+49 800 865 579 2436), free for callers in Germany.
The data provided in this data sheet is in accordance with the information available at the time of going to print and are based on the features of the German market.
Your Volkswagen dealer can provide you with information on country-specific differences.
Subject to change without notice.
02 – General information – The Crafter

Fuel consumption and CO 2 emissions for Crafter models with emission standard EEV 1) (stricter than EURO V).
With manual gearbox 2) , fuel consumption (litres/100 km) and combined CO 2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l TDI (80 kW) 2.0 l TDI (105 kW) 2.0 l TDI (120 kW)
Rear-axle
ratio 3.923:1 4.182:1 3) 4.364:1 3.923:1 4.182:1 3) 4.364:1 3.692:1 3.923:1 3) 4.182:1
Crafter 30/35 Delivery Van
urban 9.4 – 9.4 10.1 – 10.6 10.8 – 11.3 9.2 – 9.2 9.9 – 10.2 10.6 – 11.1 8.9 – 9.0 9.2 – 9.2 9.9 – 10.2
extra-urban 7.7 – 8.1 7.8 – 7.9 8.1 – 8.3 7.5 – 7.9 7.6 – 7.8 7.9 – 8.1 7.3 – 7.7 7.5 – 7.9 7.6 – 7.8
combined 8.3 – 8.6 8.6 – 8.9 9.1 – 9.4 8.1 – 8.4 8.4 – 8.7 8.9 – 9.2 7.9 – 8.2 8.1 – 8.4 8.4 – 8.7
CO 2 emissions
combined 218 – 226 226 – 234 239 – 247 213 – 221 221 – 229 234 – 242 208 – 216 213 – 221 221 – 229
Crafter 30/35 Delivery Van with start/stop system 4)
urban 9.6 – 10.0 10.3 – 10.7 9.2 – 9.5 10.1 – 10.5 8.7 – 8.7 9.2 – 9.5
extra-urban 7.6 – 7.9 7.9 – 8.1 7.5 – 7.8 7.7 – 8.1 7.3 – 7.7 7.5 – 7.8
combined 8.3 – 8.6 8.8 – 9.1 8.1 – 8.4 8.6 – 8.9 7.8 – 8.1 8.1 – 8.4
CO 2 emissions
combined 218 – 227 231 – 239 213 – 221 226 – 234 205 – 213 213 – 221
Crafter 30/35 Delivery Van with BlueMotion Technology
urban 8.6 – 8.9 8.7 – 8.7 8.2 – 8.5
extra-urban 7.7 – 7.9 7.3 – 7.7 7.3 – 7.5
combined 8.0 – 8.3 7.8 – 8.1 7.6 – 7.9
CO 2 emissions
combined 210 – 218 205 – 213 200 – 208
With Shiftmatic 2) , fuel consumption (litres/100 km) and combined CO 2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine
2.5 l BlueTDI (100 kW)
Rear-axle
ratio 4.182:1 3) 4.364:1
Crafter 30/35 Delivery Van
urban 10.3 10.6
extra-urban 8.5 8.7
combined 9.1 9.4
CO 2 emissions
combined 240 247
1) “Enhanced Environmentally Friendly Vehicle”, the figures established are below the limits set by the EURO V emission standard. 2) Figures are not available for Crafter 50.
3) Standard rear-axle ratio. 4) Start/stop system available as an optional extra.
The fuel consumption and emission values listed here have been established in accordance with the measuring method stipulated (ECE-R 101). CO 2 emissions arising from the production
and provision of fuel and/or other energy sources are not taken into consideration when determining the CO 2 emissions in accordance with directive 1999/94/EC. These figures do not
refer to the particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various types of vehicle. In addition to the fuel efficiency of a
vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO 2 emissions. CO 2 is the main greenhouse gas responsible
for global warming.
– Fuel consumption and CO 2 emissions for Crafter models with emission standard The Crafter EEV (stricter – Fuel than consumption EURO V) and – The CO 2 Crafter emissions for Crafter models with emission standard EEV (stricter than EURO V) –

Fuel consumption, CO 2 emissions and efficiency categories Crafter 4MOTION.
With manual gearbox 1) , fuel consumption (litres/100 km) and combined CO 2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine
2.0 l TDI (120 kW)
Rear-axle ratio
4.111:1 (Crafter 4MOTION with Achleitner four-wheel drive)
Crafter 35 Delivery Van (emission standard EEV 2) [stricter than EURO V])
urban 10.2
extra-urban 7.8
combined 8.7
CO 2 emissions combined 229
Crafter 35 Kombi (emission standard EEV 2) [stricter than EURO V])
urban 10.2
extra-urban 7.8
combined 8.7
CO 2 emissions combined 229
efficiency category with normal roof,
short wheelbase/medium wheelbase/–
efficiency category with high roof,
–/medium wheelbase/long wheelbase
C/C/–
–/C/C
1) Figures are not available for Crafter 50. 2) “Enhanced Environmentally Friendly Vehicle”, the figures established are below the limits set by the EURO V emission standard.
The fuel consumption and emission values listed here have been established in accordance with the measuring method stipulated (ECE-R 101). CO 2 emissions arising from the production
and provision of fuel and/or other energy sources are not taken into consideration when determining the CO 2 emissions in accordance with directive 1999/94/EC. These figures do not
refer to the particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various types of vehicle. In addition to the fuel efficiency of a
vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO 2 emissions. CO 2 is the main greenhouse gas responsible
for global warming. Note in accordance with the currently valid version of directive 1999/94/EC: A guide on the official fuel consumption and the official specific CO 2 emissions and power
consumption for all new passenger car models is available free of charge at every point of sale in the European Union and, for prospective buyers in Germany, at DAT Deutsche Automobil
Treuhand GmbH, Hellmuth-Hirth-Strasse 1, 73760 Ostfildern. Efficiency categories evaluate vehicles based on CO 2 emissions while taking the unladen weight of the vehicle into
consideration. Vehicles that comply with the average are classified as D. Vehicles that are above the current average are classified as A + , A, B or C. Vehicles that are below average are
characterised as E, F or G.
– Fuel consumption, CO 2 emissions and efficiency categories Crafter 4MOTION – The Crafter
The Crafter – Fuel consumption, CO 2 emissions and efficiency categories Crafter 4MOTION –

Fuel consumption and CO 2 emissions for Crafter models with emission standard Euro 5.
With manual gearbox 1) , fuel consumption (litres/100 km) and combined CO 2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l TDI (80 kW) 2.0 l TDI (100 kW) 2.0 l TDI (120 kW)
Rear-axle
ratio 3.923:1 4.182:1 2) 4.364:1 3.923:1 4.182:1 2) 4.364:1 3.692:1 3.923:1 2) 4.182:1
Crafter 30 Delivery Van BlueMotion (with short wheelbase and normal roof)
urban 7.9 – 8.0 7.9 – 8.0
extra-urban 6.5 – 6.6 6.5 – 6.6
combined 7.0 – 7.1 7.0 – 7.1
CO 2 emissions
combined 184 – 187 184 – 187
Crafter 30/35 Delivery Van (only models with a maximum unladen weight of 2,815 kg incl. conversions)
urban 9.1 – 9.4 10.1 – 10.7 10.5 – 10.8 9.1 – 9.4 10.1 – 10.7 10.5 – 10.8 8.7 – 9.0 9.0 – 9.2 9.9 – 10.3
extra-urban 7.9 – 8.1 7.8 – 7.9 8.4 – 8.6 7.9 – 8.1 7.8 – 7.9 8.4 – 8.6 7.5 – 7.7 7.6 – 7.9 7.6 – 7.8
combined 8.3 – 8.6 8.6 – 8.9 9.1 – 9.4 8.3 – 8.6 8.6 – 8.9 9.1 – 9.4 7.9 – 8.2 8.1 – 8.4 8.4 – 8.7
CO 2 emissions
combined 218 – 226 226 – 234 239 – 247 218 – 226 226 – 234 239 – 247 208 – 216 213 – 221 221 – 229
Crafter 30/35 Delivery Van with start/stop system 3) (only models with a maximum unladen weight of 2,815 kg incl. conversions)
urban 9.6 – 10.0 10.0 – 10.3 9.6 – 10.0 10.0 – 10.3 8.4 – 8.7 9.4 – 9.6
extra-urban 7.6 – 7.7 8.2 – 8.4 7.6 – 7.7 8.2 – 8.4 7.5 – 7.7 7.4 – 7.7
combined 8.3 – 8.6 8.8 – 9.1 8.3 – 8.6 8.8 – 9.1 7.8 – 8.1 8.1 – 8.4
CO 2 emissions
combined 218 – 226 231 – 239 218 – 226 231 – 239 205 – 213 213 – 221
Crafter 30/35 Delivery Van with BlueMotion Technology (only models with a maximum unladen weight of 2,815 kg incl. conversions)
urban 8.6 – 8.9 8.6 – 8.9 8.2 – 8.5
extra-urban 7.7 – 7.9 7.7 – 7.9 7.3 – 7.5
combined 8.0 – 8.3 8.0 – 8.3 7.6 – 7.9
CO 2 emissions
combined 210 – 218 210 – 218 199 – 208
1) Figures are not available for Crafter 50. 2) Standard rear-axle ratio. 3) Start/stop system available as an optional extra.
The fuel consumption and emission values listed here have been ascertained in accordance with the measuring method stipulated (the version of the EC directive 715/2007 which is
currently valid). CO 2 emissions arising from the production and provision of fuel and/or other energy sources are not taken into consideration when determining the CO 2 emissions in
accordance with directive 1999/94/EC. These figures do not refer to a particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various
types of vehicle. In addition to the fuel efficiency of a vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO 2
emissions. CO 2 is the main greenhouse gas responsible for global warming.
– Fuel consumption and CO 2 emissions for Crafter models with emission standard Euro 5 – The The Crafter – Fuel consumption and CO 2 emissions for Crafter models with emission standard Euro 5 –

Fuel consumption, CO 2 emissions and efficiency categories for Crafter models with emission standard Euro 5.
With manual gearbox, fuel consumption (litres/100 km) and combined CO 2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l TDI (80 kW) 2.0 l TDI (100 kW) 2.0 l TDI (120 kW)
Rear-axle ratio 3.923:1 4.182:1 1) 4.364:1 3.923:1 4.182:1 1) 4.364:1 3.692:1 3.923:1 1) 4.182:1
Crafter 30/35 Kombi
urban 9.0 9.9 10.2 9.0 9.9 10.2 8.5 8.9 9.4
extra-urban 7.3 7.2 7.9 7.3 7.2 7.9 6.9 7.0 7.2
combined 7.9 8.2 8.7 7.9 8.2 8.7 7.5 7.7 8.0
CO 2 emissions combined 208 216 229 208 216 229 197 203 210
efficiency category for Crafter 30
with normal roof, short wheelbase/
medium wheelbase/– D/D/– E/E/– E/E/– D/D/– E/E/– E/E/– D/D/– D/D/– D/D/–
efficiency category for Crafter 35
with normal roof, short wheelbase/
medium wheelbase/– D/D/– E/D/– E/E/– D/D/– E/D/– E/E/– D/D/– D/D/– D/D/–
efficiency category for Crafter 30
with high roof, –/medium
wheelbase/– –/D/– –/D/– –/E/– –/D/– –/D/– –/E/– –/C/– –/D/– –/D/–
efficiency category for Crafter 35
with high roof, –/medium
wheelbase/long wheelbase –/D/C –/D/D –/E/D –/D/C –/D/D –/E/D –/C/C –/D/C –/D/C
Crafter 30/35 Kombi with start/stop system 2)
urban 9.4 9.7 9.4 9.7 8.3 8.7
extra-urban 7.0 7.7 7.0 7.7 6.9 7.2
combined 7.9 8.4 7.9 8.4 7.4 7.7
CO 2 emissions combined 208 221 208 221 195 203
Crafter 30/35 Kombi with BlueMotion Technology
urban 8.3 8.3 8.0
extra-urban 7.1 7.1 6.7
combined 7.6 7.6 7.2
CO 2 emissions combined 199 199 189
efficiency category for Crafter 30
with normal roof, short wheelbase/
medium wheelbase/– D/D/– D/D/– E/E/– D/D/– D/D/– E/E/– C/C/– D/C/– D/D/–
efficiency category for Crafter 35
with normal roof, short wheelbase/
medium wheelbase/– D/D/– D/D/– E/E/– D/D/– D/D/– E/E/– C/C/– D/C/– D/D/–
efficiency category for Crafter 30
with high roof, –/medium
wheelbase/– –/D/– –/D/– –/E/– –/D/– –/D/– –/E/– –/C/– –/C/– –/D/–
efficiency category for Crafter 35
with high roof, –/medium
wheelbase/long wheelbase –/C/C –/D/C –/E/D –/C/C –/D/C –/E/D –/C/B –/C/C –/D/C
1) Standard rear-axle ratio. 2) Start/stop system available as an optional extra.
The values listed here have been ascertained in accordance with the measuring method stipulated (§ 2 Nrs. 5, 6, 6a of the German energy labeling directive for cars in the currently valid
version). CO 2 emissions arising from the production and provision of fuel and/or other energy sources are not taken into consideration when determining the CO 2 emissions in accordance
with directive 1999/94/EC. These figures do not refer to a particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various types of
vehicle. In addition to the fuel efficiency of a vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO 2 emissions.
CO 2 is the main greenhouse gas responsible for global warming. Note in accordance with the currently valid version of directive 1999/94/EC: A guide on the official fuel consumption and
the official specific CO 2 emissions and power consumption for all new passenger car models is available free of charge at every point of sale in the European Union and, for prospective
buyers in Germany, at DAT Deutsche Automobil Treuhand GmbH, Hellmuth-Hirth-Strasse 1, 73760 Ostfildern. Efficiency categories evaluate vehicles based on CO 2 emissions while taking
the unladen weight of the vehicle into consideration. Vehicles that comply with the average are classified as D. Vehicles that are above the current average are classified as A + , A, B or C.
Vehicles that are below average are characterised as E, F or G.
– Fuel consumption and CO 2 emissions for Crafter models with emission standard Euro 5 – The The Crafter
– Fuel consumption and CO 2 emissions for Crafter models with emission standard Euro 5 –

Engines.
Diesel engines 2.0 l TDI engine (80 kW) 2.0 l TDI engine (100 kW)
(only with Crafter 30/35)
Mixture preparation/injection method common rail direct injection common rail direct injection
No. of cylinders 4 4
Cubic capacity, cm 3 1,968 1,968
Output, kW at rpm 80 at 3,500 100 at 3,500
Max. torque, Nm/rpm 300/1,500 – 2,250 340/1,575 – 2,250
EU exhaust emission directive
EEV 1) according to regulation 2005/55/EC, according to EC regulation 715/2007 Euro 5 2)
version 2008/74/EC or according to EC
regulation 715/2007 Euro 5 respectively 2)
Diesel particulate filter (DPF) standard standard
6-speed manual gearbox standard standard
Rear-wheel drive standard standard
Type of fuel diesel, in accordance with DIN EN 590 diesel, in accordance with DIN EN 590
Diesel engines 2.5 l BlueTDI engine (100 kW) 3) 2.0 l TDI engine (105 kW)
Mixture preparation/injection method common rail direct injection BiTurbo common rail direct injection
No. of cylinders 5 4
Cubic capacity, cm 3 2,461 1,968
Output, kW at rpm 100 at 3,500 105 at 3,500
Max. torque, Nm/rpm 330/2,000 340/1,575 – 2,250
EU exhaust emission directive
EEV 1) according to regulation 2005/55/EC,
version 2008/74/EC
Diesel particulate filter (DPF) standard standard
6-speed manual gearbox/6-speed Shiftmatic –/standard standard/–
Rear-wheel drive standard standard
EEV 1) according to regulation 2005/55/EC,
version 2008/74/EC
Type of fuel diesel, in accordance with DIN EN 590 diesel, in accordance with DIN EN 590
Diesel engine
Mixture preparation/injection method
No. of cylinders 4
Cubic capacity, cm 3 1,968
Output, kW at rpm 120 at 3,600
Max. torque, Nm/rpm 400/1,800
EU exhaust emission directive
Diesel particulate filter (DPF)
6-speed manual gearbox
Rear-wheel drive
2.0 l TDI engine (120 kW)
BiTurbo common rail direct injection
EEV 1) according to regulation 2005/55/EC,
version 2008/74/EC or according to EC
regulation 715/2007 Euro 5 respectively 2)
standard
standard
standard
Type of fuel diesel, in accordance with DIN EN 590
output [kW]
80 kW
140
120
100
80
60
40
20
300 Nm
2.0 l TDI (EEV/Euro 5)
80 kW
300
250
200
150
100
50
torque [Nm]
output [kW]
100 kW
140
120
100
80
60
40
20
340 Nm
2.0 l TDI (Euro 5)
100 kW
400
350
300
250
200
150
100
50
torque [Nm]
output [kW]
100 kW
140
120
100
80
60
40
20
330 Nm
2.5 l BlueTDI (EEV)
100 kW
400
350
300
250
200
150
100
50
torque [Nm]
output [kW]
105 kW
140
120
100
80
60
40
20
340 Nm
2.0 l TDI (EEV)
105 kW
400
350
300
250
200
150
100
50
torque [Nm]
output [kW]
120 kW
140
120
100
80
60
40
20
400 Nm
2.0 l TDI (EEV/Euro 5)
120 kW
400
350
300
250
200
150
100
50
torque [Nm]
1000 2000 3000 4000 5000
1000 2000 3000 4000 5000
1000 2000 3000 4000 5000
1000 2000 3000 4000 5000
1000 2000 3000 4000 5000
engine speed [rpm]
engine speed [rpm]
engine speed [rpm]
engine speed [rpm]
engine speed [rpm]
1) “Enhanced Environmentally Friendly Vehicle”, the figures established are below the limits set by the EURO V emission standard. 2) Road tax ratings in Germany are in accordance
with the code numbers laid down by the Federal Motor Transport Authority. 3) Not available for Crafter Kombi.
– Engines – The Crafter The Crafter – Engines –

Top speeds.
With manual gearbox
Model Engine Output
(kW)
Top speeds (kph) with rear-axle ratio
3.692:1 3.923:1 4.182:1 4.364:1 4.727:1 5.1:1
Delivery Van with normal roof or high roof
Crafter 30/35 2.0 l TDI 80 149 1) 147 2) 145
2.0 l TDI 100 156 1) 154 2) 152
2.0 l TDI 105 158 1) 156 2) 154
2.0 l TDI 120 160 1) 160 2) 157
Crafter 50 3) 2.0 l TDI 80 135 1) 133 2)
2.0 l TDI 105 142 1) 140 2)
2.0 l TDI 120 154 1) 152 2) 150 144
Delivery Van with super-high roof
Crafter 35 2.0 l TDI 80 143 1) 141 2) 139
2.0 l TDI 100 149 1) 147 2) 145
2.0 l TDI 105 151 1) 149 2) 147
2.0 l TDI 120 158 1) 156 2) 153
Crafter 50 3) 2.0 l TDI 80 131 1) 129 2)
2.0 l TDI 105 137 1) 135 2)
2.0 l TDI 120 148 1) 146 2) 144 138
Kombi with normal roof or high roof
Crafter 30/35 2.0 l TDI 80 149 1) 147 2) 145
2.0 l TDI 100 156 1) 154 2) 152
2.0 l TDI 120 160 1) 160 2) 157
With Shiftmatic
Model Engine Output
(kW)
Top speeds (kph) with rear-axle ratio
4.182:1 4.364:1 4.727:1 5.1:1
Delivery Van with normal roof
Crafter 30/35 2.5 l BlueTDI 100 154 2) 150
Crafter 50 3) 2.5 l BlueTDI 100 138 135 2)
Delivery Van with high roof or super-high roof (super-high roof not for Crafter 30)
Crafter 30/35 2.5 l BlueTDI 100 150 2) 146
Crafter 50 3) 2.5 l BlueTDI 100 134 131 2)
1) Standard rear-axle ratio for Crafter Delivery Van BlueMotion (only for Crafter 30 with normal roof and 80 kW or 100 kW) as well as BlueMotion Technology. 2) Standard rear-axle ratio.
3) The maximum speeds shown here refer to non-deactivated vehicles. For deactivated vehicles, the maximum speed is 90 kph.
– Top speeds – The Crafter
The Crafter – Top speeds –

Weights.
Model/
Gross vehicle weight
(kg)
Wheelbase
(mm)
Unladen weight
with driver
(kg) 1)
from – to
Payload
(kg) 1)
from – to
Axle load limit
front/rear
(kg)
Gross train weight
12 % gradient
(kg) 2)
Delivery Van BlueMotion with normal roof
Crafter 30
3,000
3,250 1,904 – 2,075 1,096 – 925 1,650/1,800 5,000
Delivery Van with normal roof
Crafter 30
3,000
3,250 1,904 – 2,319 1,096 – 681 1,650/1,800 5,000
Crafter 35
3,500
Crafter 30
3,000
Crafter 35
3,500
Crafter 50
5,000
1,917 – 2,485 1,583 – 1,015 1,650 3) /2,250 5,300 – 6,300
3,665 1,972 – 2,319 1,028 – 681 1,650/1,800 5,000
1,985 – 2,574 1,515 – 926 1,650 3) /2,250 5,300 – 7,000 4)
2,265 – 2,954 2,735 – 2,046 1,850 5) /3,500 7,000 – 8,000 4)
Delivery Van with high roof
Crafter 30
3,000
3,665 2,008 – 2,319 992 – 681 1,650/1,800 5,000
Crafter 35
3,500
Crafter 50
5,000
Crafter 35
3,500
Crafter 50
5,000
Crafter 35
3,500
Crafter 50
5,000
2,021 – 2,610 1,479 – 890 1,650 3) /2,250 5,300 – 7,000 4)
2,301 – 2,990 2,699 – 2,010 1,850 5) /3,500 7,000 – 8,000 4)
4,325 2,155 – 2,772 1,345 – 728 1,650 3) /2,250 5,300 – 7,000 4)
2,467 – 3,184 2,533 – 1,816 1,850 5) /3,500 7,000 – 8,000 4)
4,325 with overhang 2,207 – 2,819 1,293 – 681 1,650 3) /2,250 5,300 – 6,300 4)
2,514 – 3,259 2,486 – 1,741 1,850 5) /3,500 7,000 – 8,000 4)
Delivery Van with super-high roof
Crafter 35
3,500
3,665 2,057 – 2,646 1,443 – 854 1,650 3) /2,250 5,300 – 7,000 4)
Crafter 50
5,000
Crafter 35
3,500
Crafter 50
5,000
Crafter 35
3,500
Crafter 50
5,000
2,337 – 3,026 2,663 – 1,974 1,850 5) /3,500 7,000 – 8,000 4)
4,325 2,182 – 2,799 1,318 – 701 1,650 3) /2,250 5,300 – 7,000 4)
2,494 – 3,211 2,506 – 1,789 1,850 5) /3,500 7,000 – 8,000 4)
4,325 with overhang 2,235 – 2,819 1,265 – 681 1,650 3) /2,250 5,300 – 6,300 4)
2,542 – 3,287 2,458 – 1,713 1,850 5) /3,500 7,000 – 8,000 4)
1) Equipment can result in an increase/decrease in the unladen weight and consequently affect the payload. Please consult your Volkswagen Commercial Vehicle partner. 2) Depending
on the combination of engine, final drive ratio and tow bar. 3) Depending on the equipment, the front axle load limit may increase to 1,800 kg. This can affect the minimum payload.
4) Only possible in conjunction with tow bar with increased trailer load limit (optional extra). 5) Depending on the equipment, the front axle load limit may increase to 2,000 kg. This
can affect the minimum payload.
For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all
vehicles (standard at Crafter 50).
The payloads listed here have been established allowing for factory options or other tailored solutions that are not included in the standard scope of delivery and services. The actual
payload of a vehicle, which is calculated by the difference between the gross vehicle weight and the curb weight, can only be established by weighing the individual vehicle.
– Weights – The Crafter The Crafter – Weights –

Weights.
Model/
Gross vehicle weight
(kg)
Wheelbase
(mm)
Unladen weight
with driver
(kg) 1)
Payload
(kg) 1)
Axle load limit
front/rear
(kg)
Gross train weight
12 % gradient
(kg) 2)
Kombi with normal roof
Crafter 30
3,190
Crafter 35
3,500
Crafter 30
3,190
Crafter 35
3,500
Kombi with high roof
Crafter 30
3,190
Crafter 35
3,500
Crafter 35
3,500
3,250 1,976 – 2,739 1,214 – 451 1,650 3) /1,800 5,190
1,976 – 2,783 1,524 – 717 1,650 3) /2,250 5,500 – 6,300
3,665 2,005 – 2,739 1,185 – 451 1,650 3) /1,800 5,190
2,028 – 2,801 1,472 – 699 1,650 3) /2,250 5,500 – 7,000 4)
3,665 2,041 – 2,739 1,149 – 451 1,650 3) /1,800 5,190
2,064 – 2,815 1,436 – 685 1,650 3) /2,250 5,500 – 7,000 4)
4,325 2,219 – 2,815 1,281 – 685 1,650 3) /2,250 5,500 – 7,000 4)
Roof load limits
Trailer nose weights
Model
Roof load limit
(kg)
Trailer nose weight
(kg)
With trailer nose limit
(kg)
Delivery Van and Kombi
Normal roof 300 100 2,000
High roof 150 120 2,800/3,000
Super-high roof 5) 140 3,500
1) Equipment can result in an increase/decrease in the unladen weight and consequently affect the payload. Please consult your Volkswagen Commercial Vehicle partner. 2) Depending
on the combination of engine, final drive ratio and tow bar. 3) Depending on the equipment, the front axle load limit may increase to 1,800 kg. This can affect the minimum payload.
4) Only possible in conjunction with tow bar with increased trailer load limit (optional extra). 5) There is no factory provision for a specific roof load on vehicles with a super high roof
For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all
vehicles (standard at Crafter 50).
The payloads listed here have been established allowing for factory options or other tailored solutions that are not included in the standard scope of delivery and services. The actual
payload of a vehicle, which is calculated by the difference between the gross vehicle weight and the curb weight, can only be established by weighing the individual vehicle.
– Weights – The Crafter
The Crafter – Weights –

Dimensions and weights Crafter 4MOTION.
Model/
feature
Crafter 35 4MOTION with Achleitner four-wheel drive
(Delivery Van, Kombi)
Crafter 50 4MOTION with Achleitner four-wheel
drive (Delivery Van)
Wheelbase (mm) 3,250 3,665 4,325 4,325 with
overhang
3,665 4,325 4,325 with
overhang
Ground clearance front axle
(mm) 280 280 280 280 280 280 280
Ground clearance transfer case
(mm) 300 300 300 300 295 295 295
Ground clearance rear axle
(mm)
from approx.
240 –269
from approx.
240 –269
from approx.
240 –269
from approx.
240 –269
from approx.
246 –268
from approx.
246 –268
from approx.
246 –268
Axle load limit (front/rear) (kg) 1,800/2,250 1,800/2,250 1,800/2,250 1,800/2,250 2,000/3,500 2,000/3,500 2,000/3,500
Trailer weight braked (kg)/
unbraked (kg)
2,000 –2,800/
750
2,000 –2,800/
750
2,000 –2,800/
750
2,000 –2,800/
750
2,000 –3,500/
750
2,000 –3,500/
750
2,000 –3,500/
750
Gross train weight at 12 %
gradient (kg) 5,300 – 6,300 5,300 – 7,000* 5,300 – 7,000* 5,300 – 7,000* 7,000 – 8,000* 7,000 – 8,000* 7,000 – 8,000*
Wading depth (mm) 600 600 600 600 600 600 600
Chassis elevation 4 x 4 (mm) 100 100 100 100 100 100 100
Rear-axle ratio,
ex factory/Achleitner 4.182/4.111 4.364 or 4.727 (optional)/
4.375 or 4.857 (optional)
Auxiliary drive an auxiliary drive on the main gear is possible an auxiliary drive on the main gear is possible
*Only possible in conjunction with tow bar with increased trailer load limit (optional extra).
For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all
vehicles (standard at Crafter 50).
– Dimensions and weights Crafter 4MOTION – The Crafter The Crafter – Dimensions and weights Crafter 4MOTION –

Gross train weights and trailer load limits.
With manual gearbox
Model Engine Output
Gross train weight/trailer load limit (kg) with rear-axle ratio
(kW) 3.692:1 3.923:1 4.182:1 4.364:1 4.727:1 5.1:1
Delivery Van with normal roof, high roof or super-high roof (super-high roof not for Crafter 30)
Crafter 30 2.0 l TDI 80 5,000 1) /2,000 1) 5,000 2) /2,000 2) 5,000/2,000
2.0 l TDI 100 5,000 1) /2,000 1) 5,000 2) /2,000 2) 5,000/2,000
2.0 l TDI 105 5,000 1) /2,000 1) 5,000 2) /2,000 2) 5,000/2,000
2.0 l TDI 120 5,000 1) /2,000 1) 5,000 2) /2,000 2) 5,000/2,000
Crafter 35 2.0 l TDI 80 5,500 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 3) /2,800 3)
7,000 3) /3,500 3)
2.0 l TDI 100 5,500 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 3) /2,800 3)
7,000 3) /3,500 3)
2.0 l TDI 105 5,500 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 3) /2,800 3)
2.0 l TDI 120 5,300 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 2), 3) /2,800 2), 3) 6,300 3) /2,800 3)
7,000 3) /3,500 3)
7,000 3) /3,500 3)
Crafter 50 2.0 l TDI 80 7,000 1) /2,000 1) 7,000 2) /2,000 2)
7,000 1) /3,000 1), 3) 7,000 2) 2), 3)
/3,000
7,000 1) /3,500 1), 3) 7,000 2) 2), 3)
/3,500
2.0 l TDI 105 7,000 1) /2,000 1) 7,000 2) /2,000 2)
7,000 1) /3,000 1), 3) 7,000 2) 2), 3)
/3,000
7,000 1) /3,500 1), 3) 7,000 2) 2), 3)
/3,500
2.0 l TDI 120 7,000 1) /2,000 1) 7,000 2) /2,000 2) 7,000/2,000 7,000/2,000
7,000 1) /3,000 1), 3) 7,500 2), 3) /3,000 2), 3) 8,000 3) /3,000 3) 8,000 3) /3,000 3)
Kombi with normal roof or high roof
Crafter 30 2.0 l TDI 80 5,190 1) /2,000 1) 5,190 2) /2,000 2) 5,190/2,000
2.0 l TDI 100 5,190 1) /2,000 1) 5,190 2) /2,000 2) 5,190/2,000
2.0 l TDI 120 5,190 1) /2,000 1) 5,190 2) /2,000 2) 5,190/2,000
Crafter 35 2.0 l TDI 80 5,500 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 3) /2,800 3)
7,000 3) /3,500 3)
2.0 l TDI 100 5,500 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 3) /2,800 3)
2.0 l TDI 120 5,500 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 2), 3) /2,800 2), 3) 7,000 3) /2,800 3)
7,000 1) /3,500 1), 3) 7,500 2), 3) /3,500 2), 3) 8,000 3) /3,500 3) 8,000 3) /3,500 3)
7,000 3) /3,500 3)
7,000 3) /3,500 3)
1) Standard rear-axle ratio for Crafter Delivery Van BlueMotion (only for Crafter 30 with normal roof and 80 kW or 100 kW) as well as BlueMotion Technology. 2) Standard rear-axle ratio.
3) In conjunction with tow bar with increased trailer load limit (optional extra).
– Gross train weights and trailer load limits – The Crafter
The Crafter – Gross train weights and trailer load limits –

Gross train weights and trailer load limits.
With Shiftmatic
Model Engine Output
(kW)
Gross train weight/trailer load limit (kg) with rear-axle ratio
4.182:1 4.364:1 4.727:1 5.1:1
Delivery Van with normal roof, high roof or super-high roof (super-high roof not for Crafter 30)
Crafter 30 2.5 l BlueTDI 100 5,000 1) /2,000 1) 5,000/2,000
Crafter 35 2.5 l BlueTDI 100 5,500 1) /2,000 1) 5,500/2,000
6,300 2) /2,800 2)
7,000 2) /3,500 2)
Crafter 50 2.5 l BlueTDI 100 7,000/2,000 7,000 1) /2,000 1)
7,000/3,000 2) 7,000 1) 1), 2)
/3,000
7,000/3,500 2) 7,000 1) 1), 2)
/3,500
1) Standard rear-axle ratio. 2) In conjunction with tow bar with increased trailer load limit (optional extra).
– Gross train weights and trailer load limits – The Crafter The Crafter – Gross train weights and trailer load limits –

Dimensional drawings.
Crafter 30 Delivery Van BlueMotion with short wheelbase and normal roof/
Crafter 30/35 Delivery Van with short wheelbase and normal roof
Crafter 30/35 Delivery Van with medium wheelbase and normal roof
2600
1650
3265
1650
1993 1000 3250
5240
990
1993
1000 3665
5905
1240
2426
2426
2415
1780
1350
2415
1780
1350
670
670
load compartment, volume 7.5 m 3 load compartment, volume 9.0 m 3
lateral sliding door, width/height 1,040/1,520 mm lateral sliding door, width/height 1,300/1,520 mm
rear wing doors, width/height 1,565/1,540 mm rear wing doors, width/height 1,565/1,540 mm
turning circle 12.3 m turning circle 13.6 m
Crafter 30/35 Delivery Van with medium wheelbase and high roof
Crafter 35 Delivery Van with medium wheelbase and super-high roof
3265
1940
3265
2140
1993 1000 3665
5905
1240
1993
1000 3665
5905
1240
2426
2426
2705
1780
1350
2940
1780
1350
670
670
load compartment, volume 10.5 m 3 load compartment, volume 11.5 m 3
lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm
rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm
turning circle 13.6 m turning circle 13.6 m
Crafter 35 Delivery Van with long wheelbase and high roof
Crafter 35 Delivery Van with long wheelbase and super-high roof
4300
1940
4300
2140
1993
1000 4325
6940
1615
1993
1000 4325
6940
1615
2426
2426
2705
1780
1350
2940
1780
1350
670
670
load compartment, volume 14.0 m 3 load compartment, volume 15.5 m 3
lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm
rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm
turning circle 15.6 m turning circle 15.6 m
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
– Dimensional drawings – The Crafter
The Crafter – Dimensional drawings –

Dimensional drawings.
Crafter 35 Delivery Van with long wheelbase, overhang
and high roof
Crafter 35 Delivery Van with long wheelbase, overhang
and super-high roof
4700
1993
1000 4325
7340
2015
2426
2705
1780
1350
1940
4700
1993
1000 4325
7340
2015
2426
2940
1780
1350
2140
670
670
load compartment, volume 15.5 m 3 load compartment, volume 17.0 m 3
lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm
rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm
turning circle 15.6 m turning circle 15.6 m
Crafter 50 Delivery Van with medium wheelbase and normal roof
Crafter 50 Delivery Van with medium wheelbase and high roof
3265
1650
3265
1940
1993
1000 3665
5905
1240
1993 1000 3665
5905
1240
2426
2426
2470
1780
978
2755
1780
978
725
725
load compartment, volume 9.0 m 3 load compartment, volume 10.5 m 3
lateral sliding door, width/height 1,300/1,520 mm lateral sliding door, width/height 1,300/1,820 mm
rear wing doors, width/height 1,565/1,540 mm rear wing doors, width/height 1,565/1,840 mm
turning circle 13.6 m turning circle 13.6 m
Crafter 50 Delivery Van with medium wheelbase and super-high roof
Crafter 50 Delivery Van with long wheelbase and high roof
3265
2140
4300
1940
1993
1000 3665
5905
1240
1993
1000 4325
6940
1615
2426
2426
2990
1780
978
2755
1780
978
725
720
load compartment, volume 11.5 m 3 load compartment, volume 14.0 m 3
lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm
rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm
turning circle 13.6 m turning circle 15.6 m
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
– Dimensional drawings – The Crafter The Crafter – Dimensional drawings –

Dimensional drawings.
Crafter 50 Delivery Van with long wheelbase and super-high roof
Crafter 50 Delivery Van with long wheelbase, overhang and high roof
4300
2140
4700
1940
1993
1000 4325
6940
1615
1993
1000 4325
7340
2015
2426
2426
2990
1780
978
2755
1780
978
720
725
load compartment, volume 15.5 m 3 load compartment, volume 15.5 m 3
lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm
rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm
turning circle 15.6 m turning circle 15.6 m
Crafter 50 Delivery Van with long wheelbase, overhang
and super-high roof
4700
1993
1000 4325
7340
2015
2426
2990
1780
978
2140
725
load compartment, volume 17.0 m 3
lateral sliding door, width/height
1,300/1,820 mm
rear wing doors, width/height
1,565/1,840 mm
turning circle
15.6 m
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
– Dimensional drawings – The Crafter
The Crafter – Dimensional drawings –

Dimensional drawings.
Crafter 30/35 Kombi with short wheelbase and normal roof
Crafter 30/35 Kombi with medium wheelbase and normal roof
2600
1993
1000 3250
5240
990
2426
2415
1650
3265
1993 1000 3665
5905
1240
2426
1780
1350
2415
1650
1780
1350
670
670
load compartment, volume 7.5 m 3 load compartment, volume 9.0 m 3
lateral sliding door, width/height 1,040/1,520 mm lateral sliding door, width/height 1,300/1,520 mm
rear wing doors, width/height 1,565/1,540 mm rear wing doors, width/height 1,565/1,540 mm
turning circle 12.3 m turning circle 13.6 m
Crafter 30/35 Kombi with medium wheelbase and high roof
Crafter 35 Kombi with long wheelbase and high roof
3265
1993 1000 3665
5905
1240
2426
2705
1780
1350
1940
4300
1993
1000 4325
6940
1615
2426
2705
1780
1350
1940
670
670
load compartment, volume 10.5 m 3 load compartment, volume 14.0 m 3
lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm
rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm
turning circle 13.6 m turning circle 15.6 m
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
– Dimensional drawings – The Crafter The Crafter – Dimensional drawings –

Tyre label.
Summer tyres Size Rolling resistance Wet grip Noise emission
195/75 R 16 C E – B C – B
205/75 R 16 C F – E C – B
225/75 R 16 C C C
235/65 R 16 C E – B C – B –
235/60 R 17 C E C
All seasons tyres Size Rolling resistance Wet grip Noise emission
205/75 R 16 C E B
285/65 R 16 E C
Winter tyres Size Rolling resistance Wet grip Noise emission
225/75 R 16 C E C
Fuel efficiency – the right tyre type can help you save on fuel.
Wet grip – a shorter braking distance increases safety.
External rolling noise – a quieter tyre increases your driving comfort and has a positive effect on the environment due to lower noise levels.
Placing an order for a specific tyre brand is not possible due to logistical and production process reasons.
– Tyre label – The Crafter
The Crafter – Tyre label –

Fuel consumption and CO 2 emissions for Crafter models with emission standard EEV 1) (stricter than EURO V).
With manual gearbox 2) , fuel consumption (litres/100 km) and combined CO 2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l TDI (80 kW) 2.0 l TDI (105 kW) 2.0 l TDI (120 kW)
Rear-axle
ratio 4.182:1 4.364:1 3) 4.727:1 4.182:1 4.364:1 3) 4.727:1 3.692:1 3.923:1 3) 4.182:1
Crafter 30/35 Dropside Van
urban 10.4 – 10.6 10.3 – 11.3 11.5 9.5 – 10.2 10.1 – 11.1 11.5 8.6 – 9.0 9.0 – 9.2 9.5 – 10.2
extra-urban 6.9 – 7.9 7.8 – 8.3 8.7 7.2 – 7.8 7.6 – 8.1 8.7 6.9 – 7.7 7.0 – 7.9 7.2 – 7.8
combined 8.2 – 8.9 8.7 – 9.4 9.7 8.0 – 8.7 8.5 – 9.2 9.7 7.5 – 8.2 7.7 – 8.4 8.0 – 8.7
CO 2 emissions
combined 216 – 234 229 – 247 255 210 – 229 224 – 242 255 197 – 216 203 – 221 210 – 229
Crafter 30/35 Dropside Van with start/stop system 4)
urban 9.8 – 10.7 11.0 9.6 – 10.5 11.0 8.6 – 8.7 8.9 – 9.5
extra-urban 7.7 – 8.1 8.5 7.5 – 8.1 8.5 6.8 – 7.7 7.0 – 7.8
combined 8.4 – 9.1 9.4 8.2 – 8.9 9.4 7.4 – 8.1 7.7 – 8.4
CO 2 emissions
combined 221 – 239 247 216 – 234 247 195 – 213 203 – 221
Crafter 30/35 Dropside Van with BlueMotion Technology
urban 9.4 – 10.0 8.9 – 9.5 7.8 – 8.5
extra-urban 7.0 – 7.9 7.0 – 7.8 6.9 – 7.5
combined 7.9 – 8.6 7.7 – 8.4 7.2 – 7.9
CO 2 emissions
combined 208 – 227 203 – 221 189 – 208
Rear-axle ratio
4.111:1 (Crafter 4MOTION with
Achleitner four-wheel drive)
Crafter 35 Dropside Van
urban 10.2
extra-urban 7.8
combined 8.7
CO 2 emissions
combined 229
With Shiftmatic 2) , fuel consumption (litres/100 km) and combined CO 2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine
2.5 l BlueTDI (100 kW)
Rear-axle
ratio 4.364:1 3) 4.727:1
Crafter 30/35 Dropside Van (except double cab with short wheelbase)
urban 10.6 10.9
extra-urban 8.7 8.9
combined 9.4 9.6
CO 2 emissions
combined 247 253
1) “Enhanced Environmentally Friendly Vehicle”, the figures established are below the limits set by the EURO V emission standard. 2) Figures are not available for Crafter 50.
3) Standard rear-axle ratio. 4) Start/stop system available as an optional extra.
The fuel consumption and emission values listed here have been established in accordance with the measuring method stipulated (ECE-R 101). CO 2 emissions arising from the production
and provision of fuel and/or other energy sources are not taken into consideration when determining the CO 2 emissions in accordance with directive 1999/94/EC. These figures do not
refer to the particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various types of vehicle. In addition to the fuel efficiency of a
vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO 2 emissions. CO 2 is the main greenhouse gas responsible
for global warming.
– Fuel consumption and CO 2 emissions for Crafter models with emission standard The Crafter EEV (stricter – Fuel than consumption EURO V) and – The CO 2 Crafter emissions for Crafter models with emission standard EEV (stricter than EURO V) –

Fuel consumption and CO 2 emissions for Crafter models with emission standard Euro 5.
With manual gearbox 1) , fuel consumption (litres/100 km) and combined CO 2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l TDI (80 kW) 2.0 l TDI (100 kW) 2.0 l TDI (120 kW)
Rear-axle
ratio 4.182:1 4.364:1 2) 4.727:1 4.182:1 4.364:1 2) 4.727:1 3.692:1 3.923:1 2) 4.182:1
Crafter 30/35 Dropside Van (only models with a maximum unladen weight of 2,815 kg incl. special bodies)
urban 9.8 – 10.7 10.2 – 10.8 11.5 9.8 – 10.7 10.2 – 10.8 11.5 8.4 – 9.0 8.8 – 9.2 9.6 – 10.3
extra-urban 7.3 – 7.9 7.9 – 8.6 8.7 7.3 – 7.9 7.9 – 8.6 8.7 7.0 – 7.7 7.1 – 7.9 7.1 – 7.8
combined 8.2 – 8.9 8.7 – 9.4 9.7 8.2 – 8.9 8.7 – 9.4 9.7 7.5 – 8.2 7.7 – 8.4 8.0 – 8.7
CO 2 emissions
combined 216 – 234 229 – 247 255 216 – 234 229 – 247 255 197 – 216 203 – 221 210 – 229
Crafter 30/35 Dropside Van with start/stop system 3) (only models with a maximum unladen weight of 2,815 kg incl. special bodies)
urban 9.7 – 10.3 11.0 9.7 – 10.3 11.0 8.2 – 8.7 9.2 – 9.6
extra-urban 7.7 – 8.4 8.5 7.7 – 8.4 8.5 7.0 – 7.7 6.8 – 7.7
combined 8.4 – 9.1 9.4 8.4 – 9.1 9.4 7.4 – 8.1 7.7 – 8.4
CO 2 emissions
combined 221 – 239 247 221 – 239 247 195 – 213 203 – 221
Crafter 30/35 Dropside Van with BlueMotion Technology (only models with a maximum unladen weight of 2,815 kg incl. special bodies)
urban 9.5 – 10.0 9.5 – 10.0 7.8 – 8.5
extra-urban 7.1 – 7.7 7.1 – 7.7 6.8 – 7.5
combined 7.9 – 8.6 7.9 – 8.6 7.2 – 7.9
CO 2 emissions
combined 208 – 226 208 – 226 189 – 208
1) Figures are not available for Crafter 50. 2) Standard rear-axle ratio. 3) Start/stop system available as an optional extra.
The fuel consumption and emission values listed here have been ascertained in accordance with the measuring method stipulated (the version of the EC directive 715/2007 which is
currently valid). CO 2 emissions arising from the production and provision of fuel and/or other energy sources are not taken into consideration when determining the CO 2 emissions in
accordance with directive 1999/94/EC. These figures do not refer to a particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various
types of vehicle. In addition to the fuel efficiency of a vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO 2
emissions. CO 2 is the main greenhouse gas responsible for global warming.
– Fuel consumption and CO 2 emissions for Crafter models with emission standard Euro 5 – The The Crafter
– Fuel consumption and CO 2 emissions for Crafter models with emission standard Euro 5 –

Engines.
Diesel engines 2.0 l TDI engine (80 kW) 2.0 l TDI engine (100 kW)
(only with Crafter 30/35)
Mixture preparation/injection method common rail direct injection common rail direct injection
No. of cylinders 4 4
Cubic capacity, cm 3 1,968 1,968
Output, kW at rpm 80 at 3,500 100 at 3,500
Max. torque, Nm/rpm 300/1,500 – 2,250 340/1,575 – 2,250
EU exhaust emission directive
EEV 1) according to regulation 2005/55/EC,
version 2008/74/EC or according to EC
regulation 715/2007 Euro 5 respectively
Diesel particulate filter (DPF) standard standard
6-speed manual gearbox standard standard
Rear-wheel drive standard standard
according to EC regulation 715/2007 Euro 5
Type of fuel diesel, in accordance with DIN EN 590 diesel, in accordance with DIN EN 590
Diesel engines 2.5 l BlueTDI engine (100 kW) 2) 2.0 l TDI engine (105 kW)
Mixture preparation/injection method common rail direct injection BiTurbo common rail direct injection
No. of cylinders 5 4
Cubic capacity, cm 3 2,461 1,968
Output, kW at rpm 100 at 3,500 105 at 3,500
Max. torque, Nm/rpm 330/2,000 340/1,575 – 2,250
EU exhaust emission directive
EEV 1) according to regulation 2005/55/EC,
version 2008/74/EC
Diesel particulate filter (DPF) standard standard
6-speed manual gearbox/6-speed Shiftmatic –/standard standard/–
Rear-wheel drive standard standard
EEV 1) according to regulation 2005/55/EC,
version 2008/74/EC
Type of fuel diesel, in accordance with DIN EN 590 diesel, in accordance with DIN EN 590
Diesel engine
Mixture preparation/injection method
No. of cylinders 4
Cubic capacity, cm 3 1,968
Output, kW at rpm 120 at 3,600
Max. torque, Nm/rpm 400/1,800
EU exhaust emission directive
Diesel particulate filter (DPF)
6-speed manual gearbox
Rear-wheel drive
2.0 l TDI engine (120 kW)
BiTurbo common rail direct injection
EEV 1) according to regulation 2005/55/EC,
version 2008/74/EC or according to EC
regulation 715/2007 Euro 5 respectively
standard
standard
standard
Type of fuel diesel, in accordance with DIN EN 590
output [kW]
80 kW
140
120
100
80
60
40
20
300 Nm
2.0 l TDI (EEV/Euro 5)
80 kW
300
250
200
150
100
50
torque [Nm]
output [kW]
100 kW
140
120
100
80
60
40
20
340 Nm
2.0 l TDI (Euro 5)
100 kW
400
350
300
250
200
150
100
50
torque [Nm]
output [kW]
100 kW
140
120
100
80
60
40
20
330 Nm
2.5 l BlueTDI (EEV)
100 kW
400
350
300
250
200
150
100
50
torque [Nm]
output [kW]
105 kW
140
120
100
80
60
40
20
340 Nm
2.0 l TDI (EEV)
105 kW
400
350
300
250
200
150
100
50
torque [Nm]
output [kW]
120 kW
140
120
100
80
60
40
20
400 Nm
2.0 l TDI (EEV/Euro 5)
120 kW
400
350
300
250
200
150
100
50
torque [Nm]
1000 2000 3000 4000 5000
1000 2000 3000 4000 5000
1000 2000 3000 4000 5000
1000 2000 3000 4000 5000
1000 2000 3000 4000 5000
engine speed [rpm]
engine speed [rpm]
engine speed [rpm]
engine speed [rpm]
engine speed [rpm]
1) “Enhanced Environmentally Friendly Vehicle”, the figures established are below the limits set by the EURO V emission standard. 2) Not available for Crafter Chassis/Dropside Van
with double cab and short wheelbase.
– Engines – The Crafter The Crafter – Engines –

Top speeds.
With manual gearbox
Model Engine Output
(kW)
Top speeds (kph) with rear-axle ratio
3.692:1 3.923:1 4.182:1 4.364:1 4.727:1 5.1:1
Dropside Van with single cab or double cab
Crafter 30/35 2.0 l TDI 80 137 1) 135 2) 133
2.0 l TDI 100 142 1) 140 2) 138
2.0 l TDI 105 144 1) 142 2) 140
2.0 l TDI 120 152 1) 150 2) 147
Crafter 50 3) 2.0 l TDI 80 127 1) 125 2)
2.0 l TDI 105 133 1) 131 2)
2.0 l TDI 120 142 1) 140 2) 138 132
With Shiftmatic
Model Engine Output
(kW)
Top speeds (kph) with rear-axle ratio
4.364:1 4.727:1 5.1:1
Dropside Van with single cab or double cab (except double cab with short wheelbase)
Crafter 30/35 2.5 l BlueTDI 100 145 2) 141
Crafter 50 3) 2.5 l BlueTDI 100 133 130 2)
1) Standard rear-axle ratio with BlueMotion Technology. 2) Standard rear-axle ratio. 3) The maximum speeds shown here refer to non-deactivated vehicles. For deactivated vehicles,
the maximum speed is 90 kph.
– Top speeds – The Crafter
The Crafter – Top speeds –

Weights.
Model/
Gross vehicle weight
(kg)
Wheelbase
(mm)
Unladen weight
with driver
(kg) 1)
from – to
Payload
(kg) 1)
from – to
Axle load limit
front/rear
(kg)
Gross train weight
12 % gradient
(kg) 2)
Chassis with single cab
Crafter 30
3,000
Crafter 35
3,500
Crafter 30
3,000
Crafter 35
3,500
Crafter 50
5,000
Crafter 35
3,500
Crafter 50
5,000
Chassis with double cab
Crafter 30
3,000
Crafter 35
3,500
Crafter 30
3,000
Crafter 35
3,500
Crafter 50
5,000
Crafter 35
3,500
Crafter 50
5,000
3,250 1,651 – 2,066 1,349 – 934 1,650/1,800 5,000
1,664 – 2,079 1,836 – 1,421 1,650 3) /2,250 5,300 – 6,300
3,665 1,668 – 2,084 1,332 – 916 1,650/1,800 5,000
1,681 – 2,097 1,819 – 1,403 1,650 3) /2,250 5,300 – 7,000 4)
1,906 – 2,422 3,094 – 2,578 1,850 5) /3,500 7,000 – 8,000 4)
4,325 1,711 – 2,129 1,789 – 1,371 1,650 3) /2,250 5,300 – 7,000 4)
1,944 – 2,462 3,056 – 2,538 1,850 5) /3,500 7,000 – 8,000 4)
3,250 1,849 – 2,192 1,151 – 808 1,650/1,800 5,000
1,862 – 2,277 1,638 – 1,223 1,650 3) /2,250 5,300 – 6,300
3,665 1,871 – 2,160 1,129 – 840 1,650/1,800 5,000
1,884 – 2,300 1,616 – 1,200 1,650 3) /2,250 5,300 – 7,000 4)
2,127 – 2,633 2,873 – 2,367 1,850 5) /3,500 7,000 – 8,000 4)
4,325 1,912 – 2,330 1,588 – 1,170 1,800/2,250 5,300 – 7,000 4)
2,141 – 2,576 2,859 – 2,424 1,850 5) /3,500 7,000 – 8,000 4)
1) Equipment can result in an increase/decrease in the unladen weight and consequently affect the payload. Please consult your Volkswagen Commercial Vehicle partner. 2) Depending
on the combination of engine, final drive ratio and tow bar. 3) Depending on the equipment, the front axle load limit may increase to 1,800 kg. This can affect the minimum payload.
4) Only possible in conjunction with tow bar with increased trailer load limit (optional extra). 5) Depending on the equipment, the front axle load limit may increase to 2,000 kg. This
can affect the minimum payload.
For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all
vehicles (standard at Crafter 50).
The payload ranges illustrated here have been established bearing in mind equipment that can be selected or omitted, and other features which do not belong to the standard scope of
delivery or standard specifications. A vehicle‘s actual payload, which results from calculating the difference between the gross vehicle weight and the unladen weight, can only determined
by weighing the individual vehicle.
– Weights – The Crafter The Crafter – Weights –

Weights.
Model/
Gross vehicle weight
(kg)
Wheelbase
(mm)
Unladen weight
with driver
(kg) 1)
from – to
Payload
(kg) 1)
from – to
Axle load limit
front/rear
(kg)
Gross train weight
12 % gradient
(kg) 2)
Dropside Van with single cab
Crafter 30
3,000
3,250 1,849 – 2,264 1,151 – 736 1,650/1,800 5,000
Crafter 35
3,500
Crafter 30
3,000
Crafter 35
3,500
Crafter 50
5,000
Crafter 35
3,500
Crafter 50
5,000
1,862 – 2,227 1,638 – 1,223 1,650 3) /2,250 5,500 – 6,300
3,665 1,898 – 2,314 1,102 – 686 1,650/1,800 5,000
1,911 – 2,327 1,589 – 1,173 1,650 3) /2,250 5,500 – 7,000 4)
2,207 – 2,723 2,793 – 2,277 1,850 5) /3,500 7,000 – 8,000 4)
4,325 1,990 – 2,408 1,510 – 1,092 1,650 3) /2,250 5,500 – 7,000 4)
2,291 – 2,809 2,709 – 2,191 1,850 5) /3,500 7,000 – 8,000 4)
Dropside Van with double cab
Crafter 30
3,000
3,250 2,007 – 2,350 993 – 650 1,650/1,800 5,000
Crafter 35
3,500
Crafter 30
3,000
Crafter 35
3,500
Crafter 50
5,000
Crafter 35
3,500
Crafter 50
5,000
2,020 – 2,435 1,480 – 1,065 1,650 3) /2,250 5,500 – 6,300
3,665 2,061 – 2,350 939 – 650 1,650/1,800 5,000
2,074 – 2,490 1,426 – 1,010 1,650 3) /2,250 5,500 – 7,000 4)
2,358 – 2,864 2,642 – 2,136 1,850 5) /3,500 7,000 – 8,000 4)
4,325 2,145 – 2,563 1,355 – 937 1,800/2,250 5,500 – 7,000 4)
2,434 – 2,869 2,566 – 2,131 1,850 5) /3,500 7,000 – 8,000 4)
Roof load limits
Trailer nose weights
Model
Roof load limit
(kg)
Trailer nose weight
(kg)
With trailer load limit
(kg)
Chassis and Dropside Van
Single/double cab 100 100 2,000
120 2,800/3,000
140 3,500
1) Equipment can result in an increase/decrease in the unladen weight and consequently affect the payload. Please consult your Volkswagen Commercial Vehicle partner. 2) Depending
on the combination of engine, final drive ratio and tow bar. 3) Depending on the equipment, the front axle load limit may increase to 1,800 kg. This can affect the minimum payload.
4) Only possible in conjunction with tow bar with increased trailer load limit (optional extra). 5) Depending on the equipment, the front axle load limit may increase to 2,000 kg. This
can affect the minimum payload.
For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all
vehicles (standard at Crafter 50).
The payload ranges illustrated here have been established bearing in mind equipment that can be selected or omitted, and other features which do not belong to the standard scope of
delivery or standard specifications. A vehicle‘s actual payload, which results from calculating the difference between the gross vehicle weight and the unladen weight, can only determined
by weighing the individual vehicle.
– Weights – The Crafter
The Crafter – Weights –

Dimensions and weights Crafter 4MOTION.
Model/
feature
Crafter 35 4MOTION with Achleitner four-wheel drive
(Chassis, Dropside Van)
Crafter 50 4MOTION with Achleitner
four-wheel drive (Chassis, Dropside Van)
Wheelbase (mm) 3,250 3,665 4,325 3,665 4,325
Ground clearance front axle
(mm) 280 280 280 280 280
Ground clearance transfer case
(mm) 300 300 300 295 295
Ground clearance rear axle
(mm)
from approx.
240 –269
from approx.
240 –269
from approx.
240 –269
from approx.
246 –268
from approx.
246 –268
Axle load limit (front/rear) (kg) 1,800/2,250 1,800/2,250 1,800/2,250 2,000/3,500 2,000/3,500
Trailer weight braked (kg)/
unbraked (kg)
2,000 –2,800/
750
2,000 –2,800/
750
2,000 –2,800/
750
2,000 –3,500/
750
2,000 –3,500/
750
Gross train weight at 12 %
gradient (kg) 5,300 – 6,300 5,300 –7,000* 5,300 – 7,000* 7,000 – 8,000* 7,000 – 8,000*
Wading depth (mm) 600 600 600 600 600
Chassis elevation 4 x 4 (mm) 100 100 100 100 100
Rear-axle ratio,
ex factory/Achleitner 4.182/4.111 4.364 or 4.727 (optional)/
4.375 or 4.857 (optional)
Auxiliary drive an auxiliary drive on the main gear is possible an auxiliary drive on the main gear is possible
*Only possible in conjunction with tow bar with increased trailer load limit (optional extra).
For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all
vehicles (standard at Crafter 50).
– Dimensions and weights Crafter 4MOTION – The Crafter The Crafter – Dimensions and weights Crafter 4MOTION –

Gross train weights and trailer load limits.
With manual gearbox
Model Engine Output
Gross train weight/trailer load limit (kg) with rear-axle ratio
(kW) 3.692:1 3.923:1 4.182:1 4.364:1 4.727:1 5.1:1
Chassis /Dropside Van with single cab or double cab
Crafter 30 2.0 l TDI 80 5,000 1) /2,000 1) 5,000 2) /2,000 2) 5,000/2,000
2.0 l TDI 100 5,000 1) /2,000 1) 5,000 2) /2,000 2) 5,000/2,000
2.0 l TDI 105 5,000 1) /2,000 1) 5,000 2) /2,000 2) 5,000/2,000
2.0 l TDI 120 5,000 1) /2,000 1) 5,000 2) /2,000 2) 5,000/2,000
Crafter 35 2.0 l TDI 80 5,500 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 2), 3) /2,800 2), 3) 6,300 3) /2,800 3)
7,000 2), 3) /3,500 2), 3) 7,000 3) /3,500 3)
2.0 l TDI 100 5,500 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 2), 3) /2,800 2), 3) 6,300 3) /2,800 3)
7,000 2), 3) /3,500 2), 3) 7,000 3) /3,500 3)
2.0 l TDI 105 5,500 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 2), 3) /2,800 2), 3) 6,300 3) /2,800 3)
2.0 l TDI 120 5,300 1) /2,000 1) 5,500 2) /2,000 2) 5,500/2,000
6,300 2), 3) /2,800 2), 3) 6,300 3) /2,800 3)
7,000 3) /3,500 3)
7,000 2), 3) /3,500 2), 3) 7,000 3) /3,500 3)
Crafter 50 2.0 l TDI 80 7,000 1) /2,000 1) 7,000 2) /2,000 2)
7,000 1) /3,000 1), 3) 7,000 2) 2), 3)
/3,000
7,000 1) /3,500 1), 3) 7,000 2) 2), 3)
/3,500
2.0 l TDI 105 7,000 1) /2,000 1) 7,000 2) /2,000 2)
7,000 1) /3,000 1), 3) 7,000 2) 2), 3)
/3,000
7,000 1) /3,500 1), 3) 7,000 2) 2), 3)
/3,500
2.0 l TDI 120 7,000 1) /2,000 1) 7,000 2) /2,000 2) 7,000/2,000 7,000/2,000
7,000 1) /3,000 1), 3) 7,500 2), 3) /3,000 2), 3) 8,000 3) /3,000 3) 8,000 3) /3,000 3)
7,000 1) /3,500 1), 3) 7,500 2), 3) /3,500 2), 3) 8,000 3) /3,500 3) 8,000 3) /3,500 3)
With Shiftmatic
Model Engine Output
(kW)
Gross train weight/trailer load limit (kg) with rear-axle ratio
4.182:1 4) 4.364:1 4.727:1 5.1:1
Chassis /Dropside Van with single cab or double cab (except double cab with short wheelbase)
Crafter 30 2.5 l
BlueTDI 100 5,000/2,000 5,000 2) /2,000 2) 5,000/2,000
Crafter 35
Crafter 50
2.5 l
BlueTDI 100 5,500/2,000 5,500 2) /2,000 2) 5,500/2,000
6,300 2), 3) /2,800 2), 3) 6,300 3) /2,800 3)
7,000 2), 3) /3,500 2), 3) 7,000 3) /3,500 3)
2.5 l
BlueTDI 100 7,000/2,000 7,000 2) /2,000 2)
7,000/3,000 3) 7,000 2) 2), 3)
/3,000
7,000/3,500 3) 7,000 2) 2), 3)
/3,500
1) Standard rear-axle ratio with BlueMotion Technology. 2) Standard rear-axle ratio. 3) In conjunction with tow bar with increased trailer load limit (optional extra). 4) Only
with Chassis.
– Gross train weights and trailer load limits – The Crafter
The Crafter – Gross train weights and trailer load limits –

Dimensional drawings.
Crafter 30 Chassis with single cab and short wheelbase
Crafter 30 Chassis with single cab and medium wheelbase
1990
1000 3250
5300
1050
1990
1000 3665
5865
1200
2426
2426
2360
2355
recommended exterior length for special body 3,050 mm recommended exterior length for special body 3,670 mm
turning circle 12.3 m turning circle 13.5 m
Crafter 35 Chassis with single cab and short wheelbase
Crafter 35 Chassis with single cab and medium wheelbase
1990
1000 3250
5300
1050
1990
1000 3665
5865
1200
2426
2426
2355
2345
recommended exterior length for special body 3,050 mm recommended exterior length for special body 3,670 mm
turning circle 12.3 m turning circle 13.5 m
Crafter 35 Chassis with single cab and long wheelbase
Crafter 50 Chassis with single cab and medium wheelbase
1990
1000 4325
6675
1350
1990
1000 3665
6082
1417
2426
2426
2345
2380
recommended exterior length for special body 4,425 mm recommended exterior length for special body 3,845 mm
turning circle 15.6 m turning circle 13.5 m
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
– Dimensional drawings – The Crafter The Crafter – Dimensional drawings –

Dimensional drawings.
Crafter 50 Chassis with single cab and long wheelbase
Crafter 30 Chassis with double cab and short wheelbase
1990
1000 4325
6842
1517
1990 1000 3250
5300
1050
2426
2426
2370
2375
recommended exterior length for special body 4,610 mm recommended exterior length for special body 2,160 mm
turning circle 15.6 m turning circle 12.3 m
Crafter 30 Chassis with double cab and medium wheelbase
Crafter 35 Chassis with double cab and short wheelbase
1990
1000 3665
5865
1200
1990 1000 3250
5300
1050
2426
2426
2365
2370
recommended exterior length for special body 2,770 mm recommended exterior length for special body 2,160 mm
turning circle 13.5 m turning circle 12.3 m
Crafter 35 Chassis with double cab and medium wheelbase
Crafter 35 Chassis with double cab and long wheelbase
1990
1000 3665
5865
1200
1990
1000 4325
6675
1350
2426
2426
2360
2350
recommended exterior length for special body 2,770 mm recommended exterior length for special body 3,440 mm
turning circle 13.5 m turning circle 15.6 m
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
– Dimensional drawings – The Crafter
The Crafter – Dimensional drawings –

Dimensional drawings.
Crafter 50 Chassis with double cab and medium wheelbase
Crafter 50 Chassis with double cab and long wheelbase
1990
1000 3665
6082
1417
1990
1000 4325
6842
1517
2426
2426
2400
2385
recommended exterior length for special body 2,770 mm recommended exterior length for special body 3,610 mm
turning circle 13.5 m turning circle 15.6 m
Crafter 30 Dropside Van with single cab and short wheelbase
Crafter 30 Dropside Van with single cab and medium wheelbase
400
400
2090 1000 3250
5474
2426
2350
1224
2030 965
2090 1000 3665
6024
2426
2345
1359
965
2030
2850
3400
load area 5.8 m 2 load area 6.9 m 2
turning circle 12.3 m turning circle 13.5 m
Crafter 35 Dropside Van with single cab and short wheelbase
Crafter 35 Dropside Van with single cab and medium wheelbase
400
400
2345
960
2090 1000 3250
5474
1224
2426
2030
2345
960
2090 1000 3665
6024
1359
2426
2030
2850
3400
load area 5.8 m 2 load area 6.9 m 2
turning circle 12.3 m turning circle 13.5 m
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
– Dimensional drawings – The Crafter The Crafter – Dimensional drawings –

Dimensional drawings.
Crafter 35 Dropside Van with single cab and long wheelbase
Crafter 50 Dropside Van with single cab and medium wheelbase
400
400
2330
965
2090 1000 4325
6924
1599
2426
2030
2370
1025
2190
1000 3665
6224
1559
2675
2130
4300
3600
load area 8.7 m 2 load area 7.7 m 2
turning circle 15.6 m turning circle 13.5 m
Crafter 50 Dropside Van with single cab and long wheelbase
Crafter 30 Dropside Van with double cab and short wheelbase
400
400
2190
2675
2360
1000 4325
6924
1599
1030
2130
2090 1000 3250
5554
2426
2365
1304
2030 965
4300
2120
load area 9.2 m 2 load area 4.3 m 2
turning circle 15.6 m turning circle 12.3 m
Crafter 30 Dropside Van with double cab and medium wheelbase
Crafter 35 Dropside Van with double cab and short wheelbase
400
400
965
2090 1000 3665
6134
1469
2426
2355
2030
2360
960
2090 1000 3250
5554
1304
2426
2030
2700
2120
load area 5.5 m 2 load area 4.3 m 2
turning circle 13.5 m turning circle 12.3 m
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
– Dimensional drawings – The Crafter
The Crafter – Dimensional drawings –

Dimensional drawings.
Crafter 35 Dropside Van with double cab and medium wheelbase
Crafter 35 Dropside Van with double cab and long wheelbase
400
400
2090 1000 3665
6134
2426
2350
1469
960
2030
2090 1000 4325
6834
2426
2340
1509
2030 960
2700
3400
load area 5.5 m 2 load area 6.9 m 2
turning circle 13.5 m turning circle 15.6 m
Crafter 50 Dropside Van with double cab and medium wheelbase
Crafter 50 Dropside Van with double cab and long wheelbase
400
400
2190
2675
2390
1000 3665
6134
1469
1020
2130
2190 1000 4325
1709
7034
2675
2375
2130 1030
2700
3600
load area 5.8 m 2 load area 7.7 m 2
turning circle 13.5 m turning circle 15.6 m
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
– Dimensional drawings – The Crafter The Crafter – Dimensional drawings –

Tyre label.
Summer tyres Size Rolling resistance Wet grip Noise emission
195/75 R 16 C E – B C – B
205/75 R 16 C F – E C – B
225/75 R 16 C C C
235/65 R 16 C E – B C – B –
235/60 R 17 C E C
All seasons tyres Size Rolling resistance Wet grip Noise emission
205/75 R 16 C E B
285/65 R 16 E C
Winter tyres Size Rolling resistance Wet grip Noise emission
225/75 R 16 C E C
Fuel efficiency – the right tyre type can help you save on fuel.
Wet grip – a shorter braking distance increases safety.
External rolling noise – a quieter tyre increases your driving comfort and has a positive effect on the environment due to lower noise levels.
Placing an order for a specific tyre brand is not possible due to logistical and production process reasons.
– Tyre label – The Crafter
The Crafter – Tyre label –

The Crafter
265.1190.13.18 • Printed in Germany
Subject to change without notice
Issue: November 2012
www.volkswagen-commercial-vehicles.com
Your Volkswagen Dealer