Stopwatch and Timer Calibrations - National Institute of Standards ...

More documents

Recommendations

Info

Stopwatch and Timer Calibrations Figure A1. Sample calibration certifi cate. (page 2) 66
Appendix B Appendix B References [1] B. N. Taylor and A. Thompson, (Eds.), “The International System of Units (SI),” Natl. Inst. Stand. Technol. Special Publication 330, 2008 Edition, March 2008. [2] BIPM/IEC/IFCC/ISO/IUPAC/IUPAP/OIML, Guide to the Expression of Uncertainty in Measurement (GUM), 1995. [3] International Organization for Standardization (ISO), International Vocabulary of Metrology – Basic and General Concepts and Associated Terms (VIM), 2008. [4] International Organization for Standardization (ISO), General Requirements for the Competence of Testing and Calibration Laboratories, 2005. [5] R. J. Anderson and G. L. Harris, “Specifications and Tolerances for Field Standard Stopwatches,” Natl. Inst. Stand. Technol. Handbook 105-5, October 1997. [6] Robbins, Michael, “Electronic Clocks and Watches,” Howard W. Sams Co., Indianapolis, IN, 1975. [7] J. R. Vig, “Introduction to Quartz Frequency Standards,” Army Research and Development Technical Report, SLCET-TR-92-1, October 1992 [8] North American Electric Reliability Council (NERC), “Time Error Correction,” Standard BAL-004-0, April 2005. [9] T. Butcher, L. Crown, L. Sebring, R. Suiter, J. Williams, editors, “Specifications, Tolerances, and other Technical Requirements for Weighing and Measuring Devices,” Natl. Inst. Stand. Technol. Handbook 44, 2007 edition (updated annually). [10] M. A. Lombardi, “Legal and Technical Measurement Requirements for Time and Frequency,” Measure: The Journal of Measurement Science, 1(3): 60-69, September 2006. [11] State of Pennsylvania code, 67 § 105.71(2), 2005. [12] R. M. Graham, “Calibration Techniques for Stopwatches and Timers,” Proc. 2003 National Conference of Standards Laboratories (NCSLI), 6 p., August 2003. 67
Page 1:
NIST Recommended Practice Guide Sto
Page 4 and 5:
Certain equipment, instruments or m
Page 7:
Acknowledgements ACKNOWLEDGEMENTS
Page 10 and 11:
Stopwatch and Timer Calibrations Se
Page 12 and 13:
Stopwatch and Timer Calibrations Li
Page 15 and 16:
Section 1 Introduction to Stopwatch
Page 17 and 18:
Introduction s or 42.13 s, but tha
Page 19 and 20:
Introduction basic principles that
Page 21 and 22:
Introduction and their traceabilit
Page 23 and 24:
Description of Timing Devices Sect
Page 25 and 26:
Description of Timing Devices Figu
Page 27 and 28:
Description of Timing Devices Figu
Page 29: Description of Timing Devices One
Page 32 and 33: Stopwatch and Timer Calibrations
Page 34 and 35: Stopwatch and Timer Calibrations a
Page 36 and 37: Stopwatch and Timer Calibrations 3.
Page 38 and 39: Stopwatch and Timer Calibrations 3.
Page 41 and 42: The Direct Comparison Method Secti
Page 43 and 44: The Direct Comparison Method Pleas
Page 45 and 46: The Direct Comparison Method uncer
Page 47 and 48: The Direct Comparison Method the u
Page 49 and 50: The Direct Comparison Method path,
Page 51 and 52: The Direct Comparison Method When
Page 53: The Direct Comparison Method Table
Page 56 and 57: Stopwatch and Timer Calibrations To
Page 58 and 59: Stopwatch and Timer Calibrations Fi
Page 60 and 61: Stopwatch and Timer Calibrations di
Page 62 and 63: Stopwatch and Timer Calibrations Fi
Page 65 and 66: The Time Base Method Section 7 The
Page 67 and 68: The Time Base Method effectively t
Page 69 and 70: The Time Base Method 7.B.2. Using
Page 71 and 72: Required Uncertainty Section 8 How
Page 73 and 74: Other Topics Related to Measurement
Page 75 and 76: Other Topics Related to Measurement
Page 77: Other Topics Related to Measurement
Page 82: Stopwatch and Timer Calibrations [1
show all

Stopwatch and Timer Calibrations - National Institute of Standards ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?