DMX-LED-DIMMER - DMX4ALL GmbH
DMX-LED-DIMMER - DMX4ALL GmbH DMX-LED-DIMMER - DMX4ALL GmbH
DMX-LED-Dimmer 16RGB 4 DMX-Addressing The starting address is adjustable about switch 1 to 9. Switch 1 has the valency 2 0 (=1), switch 2 the valency 2 1 (=2) and so on … finally switch 9 has the valency 2 8 (=256). The sum of the switches which are moved to ON position, represents the starting address. Switch 10 is reserved for the StandAlone-function and has to show OFF in the DMX operation mode. 1 2 4 8 16 32 64 128 256 OFF LED-Display-Codes The integrated LED is a multifunctional display. This LED lights nonstop in normal operation. If the LED does’nt lights, there is no DMX512-input-signal at the entry. Also the LED signalled the operation status. In this case the LED lights up in short pitches and then turns into off modus. The Number of flashing signals is equal to the Number of the error status: Error- Error Description Status 2 Address error Check if a valid DMX- starting address is adjusted at the DIP-switch. 4 Internal error An invalid DMX input signal is determined, invert the signal line by changing switch 2 and 3 or use a twisted pair wire.
DMX-Master-Dimmer DMX-LED-Dimmer 16RGB 5 The DMX-LED-Dimmer 16xRGB has different Master-dimmer which can be activated with Jumper: No master dimmer 1 2 3 1 2 3 1 2 3 1 2 3 Master dimmer for all channels Master dimmer per RGB group System master dimmer for all channels Master-dimmer for all channels This DMX-channel which is set up with the start address will be used the Master dimmer for all 48 Outputs. The DMX address assignment is shown as follows: Startadresse Starting address Master OUT 1 (R1) OUT 2 (G1) OUT 3 (B1) OUT 4 (R2) OUT 5 (G2) OUT 6 (B2) OUT 7 (R3) OUT 45 (B15) OUT 46 (R16) OUT 47 (G16) OUT 48 (B16) Master dimmer per RGB group For every RGBgroup one Master dimmer will be used. The DMX-address assignment is as follows: Startadresse Starting address Master 1 OUT 1 (R1) OUT 2 (G1) OUT 3 (B1) Master 2 OUT 4 (R2) OUT 5 (G2) OUT 6 (B2) Master 16 OUT 46 (R16) OUT 47 (G16) OUT 48 (B16) System master dimmer for all channels The value of the Master-dimmer corresponds with the DMX-channel 1 which will be used as Master-dimmer for all 48 Outputs. The DMX start address specifies the DMX channel on which the DMX-values begin for the outputs. The DMX address assignment is shown as follows: DMX-Kanal DMX-channel 1 1 Starting Startadresse address Master OUT 1 (R1) OUT 2 (G1) OUT 3 (B1) OUT 4 (R2) OUT 5 (G2) OUT 6 (B2) OUT 7 (R3) OUT 45 (B15) OUT 46 (R16) OUT 47 (G16) OUT 48 (B16)
- Page 1 and 2: DMX-LED-DIMMER 16x RGB User Manual
- Page 3: DMX-LED-Dimmer 16RGB 3 Connection D
- Page 7 and 8: DMX-LED-Dimmer 16RGB 7 User-defined
- Page 9 and 10: DMX-LED-Dimmer 16RGB 9 Dimensions 4
- Page 11 and 12: DMX-LED-Dimmer 16RGB 11 CE-conformi
<strong>DMX</strong>-<strong>LED</strong>-Dimmer 16RGB 4<br />
<strong>DMX</strong>-Addressing<br />
The starting address is adjustable about switch 1 to 9.<br />
Switch 1 has the valency 2 0 (=1), switch 2 the valency 2 1 (=2) and so on … finally<br />
switch 9 has the valency 2 8 (=256). The sum of the switches which are moved to ON<br />
position, represents the starting address.<br />
Switch 10 is reserved for the StandAlone-function and has to show OFF in the <strong>DMX</strong><br />
operation mode.<br />
1<br />
2<br />
4<br />
8<br />
16<br />
32<br />
64<br />
128<br />
256<br />
OFF<br />
<strong>LED</strong>-Display-Codes<br />
The integrated <strong>LED</strong> is a multifunctional display.<br />
This <strong>LED</strong> lights nonstop in normal operation. If the <strong>LED</strong> does’nt lights, there is no<br />
<strong>DMX</strong>512-input-signal at the entry.<br />
Also the <strong>LED</strong> signalled the operation status. In this case the <strong>LED</strong> lights up in short<br />
pitches and then turns into off modus. The Number of flashing signals is equal to the<br />
Number of the error status:<br />
Error- Error<br />
Description<br />
Status<br />
2 Address error Check if a valid <strong>DMX</strong>- starting address is adjusted at<br />
the DIP-switch.<br />
4 Internal error An invalid <strong>DMX</strong> input signal is determined, invert the<br />
signal line by changing switch 2 and 3 or use a<br />
twisted pair wire.
Change language