2008-2009 Bulletin â PDF - SEAS Bulletin - Columbia University
2008-2009 Bulletin â PDF - SEAS Bulletin - Columbia University
2008-2009 Bulletin â PDF - SEAS Bulletin - Columbia University
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
MECHANICAL ENGINEERING: THIRD AND FOURTH YEARS<br />
STANDARD TRACK<br />
177<br />
SEMESTER V SEMESTER VI SEMESTER VII SEMESTER VIII<br />
MECE E3018 (3) MECE E3028 (3) MECE E3038 (3) MECE E3410 (4)<br />
Lab I Lab II Lab III Engineering design<br />
MECE E3100 (3) MECE E3408 (3) MECE E3409 (3)<br />
Fluids I Graphics & design CAD<br />
REQUIRED<br />
COURSES<br />
MECE E 3301 (3) MECE E3311 (3) MECE E3601 (3)<br />
Thermodynamics Heat transfer Classical control sys.<br />
ENME E3105 (4) 1 MECE E4608 (3)<br />
Mechanics<br />
Manufacturing proc.<br />
ENME E3113 (3) ELEN E1201 (3.5)<br />
Mechanics of solids Intro. elec. eng.<br />
TECHNICAL<br />
ELECTIVES<br />
NONTECH<br />
ELECTIVES<br />
6 points 6 points<br />
3 points 6 points<br />
TOTAL POINTS 2<br />
15 15.5 15 16<br />
1 Strongly recommended to be taken in Semester III or IV.<br />
2 Students must complete 128 points to graduate.<br />
Fundamentals of Engineering (FE)<br />
Exam<br />
The FE exam is a state licensing exam<br />
and the first step toward becoming a<br />
Professional Engineer (P.E.). P.E. licensure<br />
is important for engineers to obtain—it<br />
shows a demonstrated commitment to<br />
professionalism and an established<br />
record of abilities that will help a job candidate<br />
stand out in the field. Ideally, the<br />
FE exam should be taken in the senior<br />
year while the technical material learned<br />
while pursuing the undergraduate degree<br />
is still fresh in the student’s mind. In addition<br />
to the FE exam, achieving P.E. licensure<br />
requires some years of experience<br />
and a second examination, which tests<br />
knowledge gained in engineering practice.<br />
For more information, please see<br />
www.columbia.edu/cu/mechanical/<br />
misc-pages/FE_Exam.html.<br />
The Mechanical Engineering Department<br />
strongly encourages all seniors<br />
to take this exam and offers a review<br />
course covering material relevant to<br />
the exam, including a practice exam to<br />
simulate the testing experience. The FE<br />
exam is given in the fall and spring of<br />
each year. The review course is offered<br />
in the spring semester, concluding<br />
before the spring exam.<br />
GRADUATE PROGRAMS<br />
Master of Science Degree Program<br />
The program leading to the Master of<br />
Science degree in mechanical engineering<br />
requires completion of a minimum<br />
of 30 points of approved course work<br />
consisting of no fewer than ten courses.<br />
A thesis based on either experimental,<br />
computational, or analytical research is<br />
optional and may be counted in lieu of<br />
up to 6 points of course work. In general,<br />
attainment of the degree requires one<br />
academic year of full-time study, although<br />
it may also be undertaken on a part-time<br />
basis over a correspondingly longer period.<br />
A minimum grade point average of 2.5<br />
is required for graduation.<br />
The student’s program of study is<br />
developed in consultation with a faculty<br />
adviser to reflect the student’s special<br />
interests. Typical choices include such<br />
subjects as mechanics of solids and<br />
fluids, thermodynamics, heat transfer,<br />
manufacturing engineering, robotics,<br />
kinematics, dynamics and vibrations,<br />
controls, and power generation.<br />
Nevertheless, the following guidelines<br />
must be adhered to:<br />
1.The sequence of courses selected<br />
must not be haphazard, but rather<br />
show a clearly discernible specialty.<br />
2.All courses must be at the graduate<br />
level, i.e., numbered 4000 or higher,<br />
with some 6000-level courses included.<br />
3.Every program must contain at least<br />
one course in mathematics (APMA or<br />
MATH designators) or their equivalent,<br />
covering material beyond what the<br />
student has taken previously. It should<br />
appear early in the sequence in order<br />
to serve as a basis for the technical<br />
course work.<br />
<strong>SEAS</strong> <strong>2008</strong>–<strong>2009</strong>