Technical Data Sheet - ADLER - Lacke

Pullex High-Tech
50460 ff
Product description
Special properties
Fields of application
Solvent-based wood preservative, with no aromatic content, for
Do-it-yourself and professional use, in the exterior. A combination
of high-solid alkyd resins guarantees a high body and, at the
same time a low viscosity. Very good penetration into the
wooden support.
Active ultra-violet filters guarantee long lasting weather protection.
The coating is protected against blue stain and fungal decay.
Wooden elements without stable dimensions in the exterior like
wooden houses, canopies, panels, balconies etc.
Deep pored hardwood, like oak need an earlier renovation.
On exotic wood (like Iroko) drying time may take longer.
Application
Application on new wood
Presevation coating
Redecoration coating
Diluent
Working and object
temperatures
Drying time
(ambiance temperature 20° C)
By brush; no spraying!
2 x Pullex High-Tech coloured 50460 ff, undiluted
Intermediate drying time approx. 12 hours
On surfaces which are still intact, clean off dust and soiling and
brush on Pullex High-Tech 50460 ff 1 x in one of the lighter colours.
Brush off with a brass-wire brush from heavily weathered, highly
absorbent wood remains of old paint, dust and dirt. 1 x by brush
Pullex-Imprägnier-Grund (Impregnation) 50208 for equalization
and high protection against blue stain, mould and insects.
Drying time about 12 hours.
2 x by brush Pullex High-Tech farbig 50460 ff coloured and undiluted
Intermediate Drying time about 12 hours
Apply on horizontal elements by brush 2 thin layers to avoid to
high film thickness.
The product is supplied ready for application
Not below + 5° C
Re-coatable after approx. 12 hours
12-10 (replaces 01-10) ZKL 5008
ADLER-Werk Lackfabrik, A-6130 Schwaz
Fon: 0043/5242/6922-190, Fax: 0043/5242/6922-309, Mail: info@adler-lacke.com
Our instructions are based on the current knowledge and are intended to advise the buyer/user to the best of our knowledge. They must be, however, individually
adapted to the application areas and conditions. The buyer/user takes responsibility for the suitability and use of the delivered product. It is therefore recommended to
produce a sample specimen for testing the suitability of the product. Otherwise our General Terms of Sale apply. All previous specifications become invalid with this
edition. Packaging sizes, colors and available gloss values are subject to change.

Continuation
Pullex High-Tech 50460 ff
Tools
Clean with ADLER Adlerol 80301 immediately after use
Yield value (per coat) 12 - 15 m 2 /l
Sizes of trading unit
Storage stability
Standard shades: 750 ml, 2,5 l, 5 l
W30: 750ml, 2,5 l, 10 l
At least 5 years in original closed cans
We recommend that you transfer the contents of open containers
into smaller containers to prevent jellification / skin formation.
Standard shades
Weide
Eiche
Lärche
Kiefer
Nuss
Palisander
Kastanie
willow
oak
larch
pine
nut
rosewood
chestnut
50461
50462
50463
50464
50465
50466
50469
Pullex High-Tech W30 50460 must only be used to lighten and
mix shades according to the ADLER colour-chart “edition21 Living
Wood”.
When lightening standard shades for a new coat with Pullex
High-Tech colourless 50460 you have to think about the shorter
repainting intervals (reduced UV protection). Therefore, the
shades willow or oak should be used for lightening darker
shades.
The final shade results from the colour of the glazing, the quantity
of application and the shade of the wood ground. It is advisable
to prepare a sample on original wood.
Safety information
Please refer to the Safety data sheet!
Risk of self-ignition for rags soaked with oxidative drying
products! Spread out rags soaked with Pullex High-Tech for
drying. Storage in closed metal containers or in water.