1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
Precautions on handling Warning Do not throw empty toner cartridges into fire. Doing so may cause accident and fire. Put the waste cartridge into the wrapping contained in the toner cartridge package and dispose of it as non-burnable garbage. Caution ◆Do not drop and tap the toner cartridge with force. Doing so may cause the toner to leak from the cartridge. ◆Do not directly touch the toner. If the toner gets on your skin or clothing, quickly wash it off with water. ◆Take care not to get toner in your eyes or breathe it in. If the toner gets in your eyes, wash your eyes out with lots of water and consult your physician. Notes ◆If you move the toner cartridge from a cold to a warm location, leave it in room temperature for over three hours before using it. ◆After replacing the toner, try to use it up within a six month period. A toner cartridge installed for an extended period of time will degrade the drawing quality. ◆Keep toner cartridges in a cool, dark place. ◆Use only genuine toner cartridges. 2-20
▼Replacing the toner Toner replacement procedures Notes ◆The toner must be replenished with the device power in ON status after the “Print Ready” is displayed. If the toner is replaced while the power is Off, the device will not be able to detect the amount of toner and an error status will not be cancelled even when toner has been replaced correctly. ◆Replace toner after plotting finishes. Replacing the toner during plotting may cause the operation to stop and data to be lost. Chapter 2 Basic operations 1 Open the scanner cover. 2 Remove the scanner exit guide. Lift and then pull the guide backward to remove while the cover is open. 2-21
- Page 13 and 14: Key/LCD/LED notations [ ] Indicates
- Page 15 and 16: TABLE OF CONTENTS Introduction ....
- Page 17 and 18: Manual paper feeding (cut paper) ..
- Page 19 and 20: Chapter 5 "SETUP" Menu 5-1 Setting
- Page 21 and 22: Chapter 10 "RESET" menu 10-1 Reset
- Page 23: When a print error occurs .........
- Page 26 and 27: Features This device is an electrop
- Page 28 and 29: Operating conditions This section c
- Page 30 and 31: Installation space ■Installation/
- Page 32 and 33: The following roll paper of the wid
- Page 34 and 35: Paper storing precautions are as fo
- Page 36 and 37: Right side/rear side 1 Mai
- Page 38 and 39: NON-PROPORTIONAL Control panel The
- Page 40 and 41: 5 This button turns on/off the powe
- Page 42 and 43: How to read the status displays for
- Page 44 and 45: Warming up display Warmi ng up nnn
- Page 46 and 47: Plotting procedures overview Plotti
- Page 48 and 49: Power on 1 Turn on the Main power s
- Page 50 and 51: Power off When turning the power of
- Page 52 and 53: ■Turning on the power Initial izi
- Page 54 and 55: Online and offline The device is
- Page 56 and 57: If an error message about paper sup
- Page 58 and 59: How to detach the paper rolls 1 Pul
- Page 60 and 61: E How to attach the paper roll ◆
- Page 62 and 63: 6 Close the paper roll drawer. Gent
- Page 66 and 67: 3 Close the scanner cover. Stopper
- Page 68 and 69: 8 Pull the lever to the right end.
- Page 70 and 71: Replacing the waste toner bottle Wh
- Page 72 and 73: 3 Remove the waste toner bottle fro
- Page 74 and 75: Replacing the process cartridge Whe
- Page 76 and 77: 2 Take out the Process cartridge. P
- Page 78 and 79: 6 Insert the Process cartridge. To
- Page 80 and 81: Manual paper feeding (cut paper) Th
- Page 82 and 83: 9× 12 series fixed form cut paper
- Page 84 and 85: When feeding the cut paper into the
- Page 86 and 87: Cancel printing Press the [STOP] ke
- Page 88 and 89: Web function startup method 1 The f
- Page 90 and 91: Using paper of new standard series
- Page 92 and 93: Using paper of Chinese standard ser
- Page 94 and 95: Limiting rolls to be used When limi
- Page 96 and 97: Channels and ports This device is e
- Page 98 and 99: Jobs The device manages the receive
- Page 100 and 101: (1) Setup menu Change the settings
- Page 102 and 103: PDL menu The various print paramete
- Page 104 and 105: Printing status Me nu Mo de MENU #S
- Page 106 and 107: Device menu “DEVICE” From the d
- Page 108 and 109: Function menu “FUNCTION” Press
- Page 110 and 111: Reset menu “RESET” Press the [
- Page 113 and 114: Chapter 4 Basic Menu Operation Chap
▼Replacing the toner<br />
Toner replacement procedures<br />
Notes<br />
◆The toner must be replenished with the device power in ON<br />
status after the “Print Ready” is displayed. If the toner is<br />
replaced while the power is Off, the device will not be able to<br />
detect the amount of toner and an error status will not be<br />
cancelled even when toner has been replaced correctly.<br />
◆Replace toner after plotting finishes. Replacing the toner<br />
during plotting may cause the operation to stop and data to<br />
be lost.<br />
Chapter 2 Basic operations<br />
1 Open the scanner cover.<br />
2 Remove the scanner exit guide.<br />
Lift and then pull the guide<br />
backward to remove while the<br />
cover is open.<br />
2-21