1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
Power on 1 Turn on the Main power switch located at the lower-left as seen from the rear of the device. Main power switch Press the power switch toward the ⎪ symbol (upwards). 2 Press the power key located on the control panel of this device (when the main power switch is on). Initial izing When you first turn on the power after purchasing this device, a guidance display prompts you to set the panel's display language. If this setting has already been completed, this message is omitted. LANGUAGE ✽ENGL I SH 2-4
▼Turning the power on and off When a job is saved, the following message appears and the device stands by for selection. When a job is not saved, this message is omitted. Delete Job Y=En t e r If a key input is not made, this message will time-out after about 10 seconds and the device starts up with the job in saved condition. Under normal conditions, the display reads “Wait a moment” and is changed to the following message. Sys t em Vers i on 01A N=Cance l Chapter 2 Basic operations The message is changed to “WARMING UP". Warmi ng up nnn Warm up will take about 4 minutes (about 8 minutes with LP-1010L-MF). nnn: a count down for the warm up is displayed. Pr i nt Ready The message indicates that the device is now online (“Print Ready”). In the “Print Ready” status, press the PRINT key or send data. 2-5
- Page 1: User's Guide (Plotter Unit) Network
- Page 5 and 6: Introduction Thank you for purchasi
- Page 7 and 8: Warning DO NOT touch any of the par
- Page 9 and 10: Warning labels Warning labels are a
- Page 11 and 12: How to read this manual Manual make
- Page 13 and 14: Key/LCD/LED notations [ ] Indicates
- Page 15 and 16: TABLE OF CONTENTS Introduction ....
- Page 17 and 18: Manual paper feeding (cut paper) ..
- Page 19 and 20: Chapter 5 "SETUP" Menu 5-1 Setting
- Page 21 and 22: Chapter 10 "RESET" menu 10-1 Reset
- Page 23: When a print error occurs .........
- Page 26 and 27: Features This device is an electrop
- Page 28 and 29: Operating conditions This section c
- Page 30 and 31: Installation space ■Installation/
- Page 32 and 33: The following roll paper of the wid
- Page 34 and 35: Paper storing precautions are as fo
- Page 36 and 37: Right side/rear side 1 Mai
- Page 38 and 39: NON-PROPORTIONAL Control panel The
- Page 40 and 41: 5 This button turns on/off the powe
- Page 42 and 43: How to read the status displays for
- Page 44 and 45: Warming up display Warmi ng up nnn
- Page 46 and 47: Plotting procedures overview Plotti
- Page 50 and 51: Power off When turning the power of
- Page 52 and 53: ■Turning on the power Initial izi
- Page 54 and 55: Online and offline The device is
- Page 56 and 57: If an error message about paper sup
- Page 58 and 59: How to detach the paper rolls 1 Pul
- Page 60 and 61: E How to attach the paper roll ◆
- Page 62 and 63: 6 Close the paper roll drawer. Gent
- Page 64 and 65: Precautions on handling Warning Do
- Page 66 and 67: 3 Close the scanner cover. Stopper
- Page 68 and 69: 8 Pull the lever to the right end.
- Page 70 and 71: Replacing the waste toner bottle Wh
- Page 72 and 73: 3 Remove the waste toner bottle fro
- Page 74 and 75: Replacing the process cartridge Whe
- Page 76 and 77: 2 Take out the Process cartridge. P
- Page 78 and 79: 6 Insert the Process cartridge. To
- Page 80 and 81: Manual paper feeding (cut paper) Th
- Page 82 and 83: 9× 12 series fixed form cut paper
- Page 84 and 85: When feeding the cut paper into the
- Page 86 and 87: Cancel printing Press the [STOP] ke
- Page 88 and 89: Web function startup method 1 The f
- Page 90 and 91: Using paper of new standard series
- Page 92 and 93: Using paper of Chinese standard ser
- Page 94 and 95: Limiting rolls to be used When limi
- Page 96 and 97: Channels and ports This device is e
▼Turning the power on and off<br />
When a job is saved, the following message appears and the device stands<br />
by for selection.<br />
When a job is not saved, this message is omitted.<br />
Delete Job<br />
Y=En t e r<br />
If a key input is not made,<br />
this message will time-out<br />
after about 10 seconds<br />
and the device starts up<br />
with the job in saved<br />
condition.<br />
Under normal conditions, the display reads “Wait a moment” and is<br />
changed to the following message.<br />
Sys t em Vers i on<br />
01A<br />
N=Cance l<br />
Chapter 2 Basic operations<br />
The message is changed to “WARMING UP".<br />
Warmi ng up nnn<br />
Warm up will take about 4<br />
minutes (about 8 minutes<br />
with LP-1010L-MF).<br />
nnn: a count down for the<br />
warm up is displayed.<br />
Pr i nt<br />
Ready<br />
The message indicates that the device is now online (“Print Ready”).<br />
In the “Print Ready” status, press the PRINT key or send data.<br />
2-5