1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
Plotting procedures overview Plotting is usually conducted in accordance with the following procedures. For information on computer operations, refer to your computer manual. 1 Turn on the power for the computer and this device. For information on turning on the device power, refer to “Turning the power on and off.” (⇒ page 2-3) 2 Confirm the status of the device on the control panel. Confirm that the LEDs are not indicating abnormalities and that the LCD indicates Data standby status. ◆ When using the copy, delivery, or file function, see “User's Guide, Copy Part” separately. Press [PRINT] key when the MENU LED is on. When the TONER LED is flashing or off, replace the toner. (⇒ page 2-19) When the WASTE TONER LED is flashing or off, replace the waste bottle. (⇒ page 2-26) When the PROCESS LED is flashing or on, replace the process cartridge. (⇒ page 2-30) When the ERROR LED is on, refer to chapter 14 for information on troubleshooting. 3 Open your application software on your computer and create a drawing. If the device settings do not conform to the application software you are using, reset the settings for this device (⇒ Chapters 5 to 12). 4 Send the data from the computer to this device. 2-2
NON-PROPORTIONAL Turning the power on and off This device has two power switches: the main power switch located at the lower-left as seen from the rear of the device; and the power key on the control panel. The device power is turned on by first turning on the main power switch, and then pressing the device’s control panel power key. Notes ◆While data is being processed, do not turn off the main power switch. Doing so may damage the system. ◆When the power is on and the Main power switch is turned off, or when the power goes out due to blackout etc., restoring the power (turning the Main power switch back on or resetting from a blackout) is the first step, but will not turn the plotter on. You must also turn ON the power key on the control panel. Chapter 2 Basic operations Main power switch Control panel [POWER] key WARNING LIGHT MENU COPY PRINT MEMORY RESET POWER POWER SAVING DELIVERY FILE REPRINT STOP SCAN STOP WASTE TONER TONER PROCESS MANUAL FEED ORIGINAL SIZE AUTO FIXED-SIZE PORTRAIT ORIGINAL TYPE TEXT/LINE TEXT/PHOTO BACKGROUND REMOVAL DENSITY DARK SCALE x1 FIXED SCALE PAPER FEED ORIGINAL FIXED-SIZE LANDSCAPE PHOTO NORMAL ZOOM IMAGE QUALITY START SYNCHRO BLUE PRINT LIGHT SCALE SORT DATA ERROR FUNCTION 2-3
- Page 1: User's Guide (Plotter Unit) Network
- Page 5 and 6: Introduction Thank you for purchasi
- Page 7 and 8: Warning DO NOT touch any of the par
- Page 9 and 10: Warning labels Warning labels are a
- Page 11 and 12: How to read this manual Manual make
- Page 13 and 14: Key/LCD/LED notations [ ] Indicates
- Page 15 and 16: TABLE OF CONTENTS Introduction ....
- Page 17 and 18: Manual paper feeding (cut paper) ..
- Page 19 and 20: Chapter 5 "SETUP" Menu 5-1 Setting
- Page 21 and 22: Chapter 10 "RESET" menu 10-1 Reset
- Page 23: When a print error occurs .........
- Page 26 and 27: Features This device is an electrop
- Page 28 and 29: Operating conditions This section c
- Page 30 and 31: Installation space ■Installation/
- Page 32 and 33: The following roll paper of the wid
- Page 34 and 35: Paper storing precautions are as fo
- Page 36 and 37: Right side/rear side 1 Mai
- Page 38 and 39: NON-PROPORTIONAL Control panel The
- Page 40 and 41: 5 This button turns on/off the powe
- Page 42 and 43: How to read the status displays for
- Page 44 and 45: Warming up display Warmi ng up nnn
- Page 48 and 49: Power on 1 Turn on the Main power s
- Page 50 and 51: Power off When turning the power of
- Page 52 and 53: ■Turning on the power Initial izi
- Page 54 and 55: Online and offline The device is
- Page 56 and 57: If an error message about paper sup
- Page 58 and 59: How to detach the paper rolls 1 Pul
- Page 60 and 61: E How to attach the paper roll ◆
- Page 62 and 63: 6 Close the paper roll drawer. Gent
- Page 64 and 65: Precautions on handling Warning Do
- Page 66 and 67: 3 Close the scanner cover. Stopper
- Page 68 and 69: 8 Pull the lever to the right end.
- Page 70 and 71: Replacing the waste toner bottle Wh
- Page 72 and 73: 3 Remove the waste toner bottle fro
- Page 74 and 75: Replacing the process cartridge Whe
- Page 76 and 77: 2 Take out the Process cartridge. P
- Page 78 and 79: 6 Insert the Process cartridge. To
- Page 80 and 81: Manual paper feeding (cut paper) Th
- Page 82 and 83: 9× 12 series fixed form cut paper
- Page 84 and 85: When feeding the cut paper into the
- Page 86 and 87: Cancel printing Press the [STOP] ke
- Page 88 and 89: Web function startup method 1 The f
- Page 90 and 91: Using paper of new standard series
- Page 92 and 93: Using paper of Chinese standard ser
- Page 94 and 95: Limiting rolls to be used When limi
Plotting procedures overview<br />
Plotting is usually conducted in accordance with the following<br />
procedures.<br />
For information on computer operations, refer to your computer manual.<br />
1 Turn on the power for the computer and this device.<br />
For information on turning on the device power, refer to “Turning the<br />
power on and off.” (⇒ page 2-3)<br />
2 Confirm the status of the device on the control panel.<br />
Confirm that the LEDs are not indicating abnormalities and that the LCD<br />
indicates Data standby status.<br />
◆<br />
When using the copy, delivery, or file function, see “User's<br />
Guide, Copy Part” separately.<br />
Press [PRINT] key when the MENU LED is on.<br />
When the TONER LED is flashing or off, replace the toner. (⇒ page 2-19)<br />
When the WASTE TONER LED is flashing or off, replace the waste<br />
bottle. (⇒ page 2-26)<br />
When the PROCESS LED is flashing or on, replace the process cartridge.<br />
(⇒ page 2-30)<br />
When the ERROR LED is on, refer to chapter 14 for information on<br />
troubleshooting.<br />
3 Open your application software on your computer and<br />
create a drawing.<br />
If the device settings do not conform to the application software you are<br />
using, reset the settings for this device (⇒ Chapters 5 to 12).<br />
4 Send the data from the computer to this device.<br />
2-2