1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
How to read the status displays for this device This section explains the control panel LEDs and LCD which inform you of the status of the device. The following are the main displays. Data standby display Standard configuration Pr int Ready Print This is a print ready status. Data processing display Number of prints executed Number of prints scheduled Process ing 02/99 Wa i t :012 F01 HPGL JobNo . 008✽ PDL name HPGL DSCAN TIFF CALS Communication channel name F : FTP protocol L : LPD protocol X : XPT protocol PR : Parallel USB : USB Print Indicates that data is being processed. (flashing) xxx: The job number standing by for processing xxx: The job number being processed Port number (this number is not displayed when using parallel or USB interface.) Data is being processed. The various information for the data currently being processed is displayed. Note ◆Parallel and USB are only displayed when each interface is installed. 1-18
▼How to read the status displays for this device Printing in progress display Print information display Print Wa i t :012 F01 HPGL JobNo .008✽ Data is being printed. The various information for the data currently being printed is displayed. T o t a l Co u n t mmm mm T o t a l Ru n (m) mmm mm Print Print Chapter 1 Before using this device This display appears when [ ] is pressed in data standby or print ready status. The total number of prints and the length of media printed appear. ◆ ◆ Customers who have signed a maintenance agreement regularly telephone our service center for assistance. When contacting our service center, please make a note of this information for your reference. This display appears for approximately three seconds, after which the display will automatically return to the original data standby display condition. Setting ready display Menu Mod e MENU #SETUP Menu The functions for this device can be set. ⇒ chapter 3 Error display Close Door1 Error An error has occurred. Errors are classified according to those which can be dealt with by the operator, or errors which can only be dealt with by your dealer or our service center, etc. ⇒ Chapter 14 1-19
- Page 1: User's Guide (Plotter Unit) Network
- Page 5 and 6: Introduction Thank you for purchasi
- Page 7 and 8: Warning DO NOT touch any of the par
- Page 9 and 10: Warning labels Warning labels are a
- Page 11 and 12: How to read this manual Manual make
- Page 13 and 14: Key/LCD/LED notations [ ] Indicates
- Page 15 and 16: TABLE OF CONTENTS Introduction ....
- Page 17 and 18: Manual paper feeding (cut paper) ..
- Page 19 and 20: Chapter 5 "SETUP" Menu 5-1 Setting
- Page 21 and 22: Chapter 10 "RESET" menu 10-1 Reset
- Page 23: When a print error occurs .........
- Page 26 and 27: Features This device is an electrop
- Page 28 and 29: Operating conditions This section c
- Page 30 and 31: Installation space ■Installation/
- Page 32 and 33: The following roll paper of the wid
- Page 34 and 35: Paper storing precautions are as fo
- Page 36 and 37: Right side/rear side 1 Mai
- Page 38 and 39: NON-PROPORTIONAL Control panel The
- Page 40 and 41: 5 This button turns on/off the powe
- Page 44 and 45: Warming up display Warmi ng up nnn
- Page 46 and 47: Plotting procedures overview Plotti
- Page 48 and 49: Power on 1 Turn on the Main power s
- Page 50 and 51: Power off When turning the power of
- Page 52 and 53: ■Turning on the power Initial izi
- Page 54 and 55: Online and offline The device is
- Page 56 and 57: If an error message about paper sup
- Page 58 and 59: How to detach the paper rolls 1 Pul
- Page 60 and 61: E How to attach the paper roll ◆
- Page 62 and 63: 6 Close the paper roll drawer. Gent
- Page 64 and 65: Precautions on handling Warning Do
- Page 66 and 67: 3 Close the scanner cover. Stopper
- Page 68 and 69: 8 Pull the lever to the right end.
- Page 70 and 71: Replacing the waste toner bottle Wh
- Page 72 and 73: 3 Remove the waste toner bottle fro
- Page 74 and 75: Replacing the process cartridge Whe
- Page 76 and 77: 2 Take out the Process cartridge. P
- Page 78 and 79: 6 Insert the Process cartridge. To
- Page 80 and 81: Manual paper feeding (cut paper) Th
- Page 82 and 83: 9× 12 series fixed form cut paper
- Page 84 and 85: When feeding the cut paper into the
- Page 86 and 87: Cancel printing Press the [STOP] ke
- Page 88 and 89: Web function startup method 1 The f
- Page 90 and 91: Using paper of new standard series
▼How to read the status displays for this device<br />
Printing in progress display<br />
Print information display<br />
Print<br />
Wa i t :012<br />
F01 HPGL JobNo .008✽<br />
Data is being printed.<br />
The various information for the data currently being printed is displayed.<br />
T o t a l Co u n t mmm mm<br />
T o t a l Ru n (m) mmm mm<br />
Print<br />
Print<br />
Chapter 1 Before using this device<br />
This display appears when [ ] is pressed in data standby or print ready status.<br />
The total number of prints and the length of media printed appear.<br />
◆<br />
◆<br />
Customers who have signed a maintenance agreement<br />
regularly telephone our service center for assistance. When<br />
contacting our service center, please make a note of this<br />
information for your reference.<br />
This display appears for approximately three seconds, after<br />
which the display will automatically return to the original data<br />
standby display condition.<br />
Setting ready display<br />
Menu Mod e<br />
MENU<br />
#SETUP<br />
Menu<br />
The functions for this device can be set. ⇒ chapter 3<br />
Error display<br />
Close Door1<br />
Error<br />
An error has occurred.<br />
Errors are classified according to those which can be dealt with by the operator, or<br />
errors which can only be dealt with by your dealer or our service center, etc. ⇒<br />
Chapter 14<br />
1-19