1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
Right side/rear side 1 Main power switch Turns the device power on and off. (⇒ page 2-3) 2 Power cord Plug this cord into a power cord socket. 3 Parallel interface connector This is an interface connector conforming to the standards of the Parallel interface connector of Centronix. 4 Ethernet interface connector This is an interface connector for a 100 BASE-TX and 10 BASE-T Ethernet interface connector. 5 USB interface connector This is an interface connector for a USB 2.0 interface connector. 6 Cutter door (door 5) Open this door to deal with paper jams at the cutter area. (⇒ page 14-3) 7 Cutter door inside (door 9) Open this door to deal with paper jams at the cutter area. (⇒ page 14-3) 8 Cutter door lower small door (door 10) Open this door to deal with paper jams at the cutter area. 9 Toner cover Open this cover when replacing toner. (⇒ page 2-19) 1-12
▼The names and functions of each part Interior Chapter 1 Before using this device 1 Paper feed knob Feeds the end of the roll to the paper feed inlet. (⇒ page 2-11) 2 Paper flange This flange is attached to the roll paper. (⇒ page 2-11) 1-13
- Page 1: User's Guide (Plotter Unit) Network
- Page 5 and 6: Introduction Thank you for purchasi
- Page 7 and 8: Warning DO NOT touch any of the par
- Page 9 and 10: Warning labels Warning labels are a
- Page 11 and 12: How to read this manual Manual make
- Page 13 and 14: Key/LCD/LED notations [ ] Indicates
- Page 15 and 16: TABLE OF CONTENTS Introduction ....
- Page 17 and 18: Manual paper feeding (cut paper) ..
- Page 19 and 20: Chapter 5 "SETUP" Menu 5-1 Setting
- Page 21 and 22: Chapter 10 "RESET" menu 10-1 Reset
- Page 23: When a print error occurs .........
- Page 26 and 27: Features This device is an electrop
- Page 28 and 29: Operating conditions This section c
- Page 30 and 31: Installation space ■Installation/
- Page 32 and 33: The following roll paper of the wid
- Page 34 and 35: Paper storing precautions are as fo
- Page 38 and 39: NON-PROPORTIONAL Control panel The
- Page 40 and 41: 5 This button turns on/off the powe
- Page 42 and 43: How to read the status displays for
- Page 44 and 45: Warming up display Warmi ng up nnn
- Page 46 and 47: Plotting procedures overview Plotti
- Page 48 and 49: Power on 1 Turn on the Main power s
- Page 50 and 51: Power off When turning the power of
- Page 52 and 53: ■Turning on the power Initial izi
- Page 54 and 55: Online and offline The device is
- Page 56 and 57: If an error message about paper sup
- Page 58 and 59: How to detach the paper rolls 1 Pul
- Page 60 and 61: E How to attach the paper roll ◆
- Page 62 and 63: 6 Close the paper roll drawer. Gent
- Page 64 and 65: Precautions on handling Warning Do
- Page 66 and 67: 3 Close the scanner cover. Stopper
- Page 68 and 69: 8 Pull the lever to the right end.
- Page 70 and 71: Replacing the waste toner bottle Wh
- Page 72 and 73: 3 Remove the waste toner bottle fro
- Page 74 and 75: Replacing the process cartridge Whe
- Page 76 and 77: 2 Take out the Process cartridge. P
- Page 78 and 79: 6 Insert the Process cartridge. To
- Page 80 and 81: Manual paper feeding (cut paper) Th
- Page 82 and 83: 9× 12 series fixed form cut paper
- Page 84 and 85: When feeding the cut paper into the
Right side/rear side<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
1 Main power switch Turns the device power on and off. (⇒ page 2-3)<br />
2 Power cord Plug this cord into a power cord socket.<br />
3 Parallel interface connector<br />
This is an interface connector conforming to the standards of the<br />
Parallel interface connector of Centronix.<br />
4 Ethernet interface connector<br />
This is an interface connector for a 100 BASE-TX and 10 BASE-T<br />
Ethernet interface connector.<br />
5 USB interface connector This is an interface connector for a USB 2.0 interface connector.<br />
6 Cutter door (door 5) Open this door to deal with paper jams at the cutter area.<br />
(⇒ page 14-3)<br />
7 Cutter door inside (door 9)<br />
Open this door to deal with paper jams at the cutter area.<br />
(⇒ page 14-3)<br />
8 Cutter door lower small door (door 10)<br />
Open this door to deal with paper jams at the cutter area.<br />
9 Toner cover Open this cover when replacing toner. (⇒ page 2-19)<br />
1-12