1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
W UN- INI T . NVRAM Description : This message appears if the nonvolatile memory (NVRAM) of the device is not initialized. Measure : The display of this warning message continues until the [Enter] key is pressed. After the [Enter] key is pressed, the NVRAM is initialized automatically and the display changes to the language setting specifically for the installing operation. 14-22
▼When an error message appears ■Communication warnings Description : A communication error message appears if any communication error occurs between the computer and the device. For a practical description, see the following table. Measure : If the device does not recover from this error by turning the power off and on, follow the guidelines described in the Measure column of the table. If the error is not removed, please notify your dealer or our service center of the displayed error message and error condition. Note ◆ A communication warning appears on the LCD, but it disappears when the next operation is performed. Consequently, you may not recognize that the error occurred. In such a case, retransmit the data to check if the communication warning is displayed on the LCD. (1) Ethernet interface xxxx: Error code W INTERFACE-LN xxxx Chapter 14 Troubleshooting Error code Description Measure 0101 Duplication of XPT port number 0212 Lack of internal memory 0220 to 022F 0250 to 025F 0260 to 026F 1000 to 4FFF 5000 to 7FFF Protocol data sent from the host is defective Host disconnects the communication forcibly while a connection is established Communication to the host failed while communication time out data is transferred Communication connection system error Communication system internal error Specify the parameter at the device side correctly. If the device does not recover from this error by turning the power off and on, take the following measures: - Check if the communication condition and protocol match the specifications of the computer. - Check if the connection cable is defective or is connected securely. - If the error is not removed, please notify your dealer or our service center of the displayed error message and error condition. 14-23
- Page 196 and 197: ■USB Specifies the USB interface
- Page 198 and 199: A SERIES ROLL A0 (841 mm / 33.1 inc
- Page 200 and 201: ■Each size paper of each series S
- Page 202 and 203: SCAN START Allows for determining w
- Page 204 and 205: LANGUAGE Switches the message displ
- Page 206 and 207: ◆ If the [Enter] key is pressed w
- Page 208 and 209: Setting items Ethernet parameter is
- Page 210 and 211: PORT SELECT Selects the Ethernet po
- Page 212 and 213: ROUTING TABLE Specifies the routing
- Page 214 and 215: ■METRIC Specifies the metric. 1
- Page 216 and 217: ■FTP DATA TYPE Specifies the init
- Page 218 and 219: ●PORT Port is enabled and can be
- Page 220 and 221: About Terioplot The Terioplot softw
- Page 222 and 223: Settings In order to operate the pl
- Page 225 and 226: Chapter 14 Troubleshooting Chapter
- Page 227 and 228: When an error message appears When
- Page 229 and 230: ▼When an error message appears 3
- Page 231 and 232: ▼When an error message appears
- Page 233 and 234: ▼When an error message appears 3
- Page 235 and 236: ▼When an error message appears
- Page 237 and 238: ▼When an error message appears 5
- Page 239 and 240: ▼When an error message appears
- Page 241 and 242: ▼When an error message appears
- Page 243 and 244: ▼When an error message appears Op
- Page 245: ▼When an error message appears W
- Page 249 and 250: ▼When an error message appears (4
- Page 251 and 252: ▼When an error message appears (5
- Page 253 and 254: ▼When an error message appears (1
- Page 255 and 256: ▼When an error message appears (2
- Page 257 and 258: ▼When an error message appears
- Page 259 and 260: ▼When an error message appears
- Page 261 and 262: ▼When an error message appears (6
- Page 263 and 264: ▼When an error message appears (1
- Page 265 and 266: Error log ▼When an error message
- Page 267 and 268: ▼Error log Type of Error Log The
- Page 269 and 270: ▼Error log Error Log Classificati
- Page 271 and 272: ▼Troubleshooting for ethernet Cau
- Page 273 and 274: When a print error occurs This sect
- Page 275 and 276: ▼ Basic Specifications Appendix A
- Page 277 and 278: ▼ Basic specifications (2/2) Item
- Page 279 and 280: ▼ Menu structure A Note ( 5 ) TIF
- Page 281 and 282: ▼ Menu structure C C' Note ( 7 )
- Page 283 and 284: ▼ Menu structure E E' #PEN PARAME
- Page 285 and 286: ▼ Menu structure [PAPER] MENU MEN
- Page 287 and 288: ○ ○ ○ ○ ▼ Menu structure
- Page 289 and 290: ▼ Menu structure [SYSTEM] MENU ME
- Page 291 and 292: ▼ Menu structure H SYSTEM #APPLY
- Page 293 and 294: ▼ Menu structure J #SCAN START >O
- Page 295 and 296: ▼ Menu structure L #CONNECTION TY
W UN- INI T .<br />
NVRAM<br />
Description : This message appears if the nonvolatile memory<br />
(NVRAM) of the device is not initialized.<br />
Measure : The display of this warning message continues until the<br />
[Enter] key is pressed.<br />
After the [Enter] key is pressed, the NVRAM is<br />
initialized automatically and the display changes to the<br />
language setting specifically for the installing operation.<br />
14-22