1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
Warning ■Operator notice warning W SPOOL INITIALIZED Description : The saved job has been damaged, and thus the spool area is initialized (When HDD is installed). Measure : After 3 seconds, the message changes to “WAIT A MOMENT” and then the device starts. W Job Delete Description : The received data is in a format not supported by the device, and thus the data was ignored. Measure : Use the data in a format supported by the device. W SPOOL ERROR Description : The spool area on the HDD has been damaged, and thus the memory spool area is used (When HDD is installed). Measure : If the device does not recover from this error when you turn the power off and on, please notify your dealer or our service center of the displayed error message and error condition. 14-20
▼When an error message appears W NVRAM ERROR Description : The nonvolatile memory (NVRAM) of the device has been damaged. Usual printing can be performed, but some functions that use this area may not operate correctly. Measure : If the device does not recover from this error by turning the power off and on, please notify your dealer or our service center of the displayed error message and error condition. Delete Job Y=En t e r N=Cance l Description : This message appears if there is an unprocessed job (jobs standing by for processing) at powering on. Measure : Select whether the job is deleted or not by pressing the [Enter] key or [Cancel] key. The operation goes in to time-out in about 10 seconds unless the key is pressed, and the device starts with the job saved. Chapter 14 Troubleshooting If a job has been left at powering on Job status Display Transaction Standing for processing DELETE JOB Job is deleted by designation. Processing - Processed - Job is automatically moved to "already processed" job. Jobs are automatically deleted in order from the oldest job. 14-21
- Page 194 and 195: ■Scanner ●DELIVERY HOST IP ADDR
- Page 196 and 197: ■USB Specifies the USB interface
- Page 198 and 199: A SERIES ROLL A0 (841 mm / 33.1 inc
- Page 200 and 201: ■Each size paper of each series S
- Page 202 and 203: SCAN START Allows for determining w
- Page 204 and 205: LANGUAGE Switches the message displ
- Page 206 and 207: ◆ If the [Enter] key is pressed w
- Page 208 and 209: Setting items Ethernet parameter is
- Page 210 and 211: PORT SELECT Selects the Ethernet po
- Page 212 and 213: ROUTING TABLE Specifies the routing
- Page 214 and 215: ■METRIC Specifies the metric. 1
- Page 216 and 217: ■FTP DATA TYPE Specifies the init
- Page 218 and 219: ●PORT Port is enabled and can be
- Page 220 and 221: About Terioplot The Terioplot softw
- Page 222 and 223: Settings In order to operate the pl
- Page 225 and 226: Chapter 14 Troubleshooting Chapter
- Page 227 and 228: When an error message appears When
- Page 229 and 230: ▼When an error message appears 3
- Page 231 and 232: ▼When an error message appears
- Page 233 and 234: ▼When an error message appears 3
- Page 235 and 236: ▼When an error message appears
- Page 237 and 238: ▼When an error message appears 5
- Page 239 and 240: ▼When an error message appears
- Page 241 and 242: ▼When an error message appears
- Page 243: ▼When an error message appears Op
- Page 247 and 248: ▼When an error message appears
- Page 249 and 250: ▼When an error message appears (4
- Page 251 and 252: ▼When an error message appears (5
- Page 253 and 254: ▼When an error message appears (1
- Page 255 and 256: ▼When an error message appears (2
- Page 257 and 258: ▼When an error message appears
- Page 259 and 260: ▼When an error message appears
- Page 261 and 262: ▼When an error message appears (6
- Page 263 and 264: ▼When an error message appears (1
- Page 265 and 266: Error log ▼When an error message
- Page 267 and 268: ▼Error log Type of Error Log The
- Page 269 and 270: ▼Error log Error Log Classificati
- Page 271 and 272: ▼Troubleshooting for ethernet Cau
- Page 273 and 274: When a print error occurs This sect
- Page 275 and 276: ▼ Basic Specifications Appendix A
- Page 277 and 278: ▼ Basic specifications (2/2) Item
- Page 279 and 280: ▼ Menu structure A Note ( 5 ) TIF
- Page 281 and 282: ▼ Menu structure C C' Note ( 7 )
- Page 283 and 284: ▼ Menu structure E E' #PEN PARAME
- Page 285 and 286: ▼ Menu structure [PAPER] MENU MEN
- Page 287 and 288: ○ ○ ○ ○ ▼ Menu structure
- Page 289 and 290: ▼ Menu structure [SYSTEM] MENU ME
- Page 291 and 292: ▼ Menu structure H SYSTEM #APPLY
- Page 293 and 294: ▼ Menu structure J #SCAN START >O
Warning<br />
■Operator notice warning<br />
W SPOOL<br />
INITIALIZED<br />
Description : The saved job has been damaged, and thus the spool area<br />
is initialized (When HDD is installed).<br />
Measure : After 3 seconds, the message changes to “WAIT A<br />
MOMENT” and then the device starts.<br />
W Job Delete<br />
Description : The received data is in a format not supported by the<br />
device, and thus the data was ignored.<br />
Measure : Use the data in a format supported by the device.<br />
W SPOOL<br />
ERROR<br />
Description : The spool area on the HDD has been damaged, and thus<br />
the memory spool area is used (When HDD is installed).<br />
Measure : If the device does not recover from this error when you<br />
turn the power off and on, please notify your dealer or<br />
our service center of the displayed error message and<br />
error condition.<br />
14-20