1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
■FTP DATA TYPE Specifies the initial value of the data transfer type when receiving ftp data. : Default value ASCII/BIN/BIN ■SNMP Specifies the SNMP operation. When the setting is ON, SNMP is enabled. The SNMP community name can be specified using the Web name. : Default value ON/OFF ■SNMP VERSION Specifies the SNMP version. : Default value V1/V2 ■TRAP** (** : 01 - 02) ●MANAGER Specifies the manager IP address to return TRAP. When the following TRAP conditions are OFF, TRAP does not occur in this setting. 000.000.000.000 to 255.255.255.255 Default value: 000.000.000.000 (TRAP is the same when it is OFF if not registered.) 12-10
▼Setting items ●ERROR Specifies whether to transmit the TRAP if an engine-related error occurs (except for technical call error). When an error occurs, TRAP is sent to the TRAP manager which was specified in the TRAP manager described above. If the TRAP manager item is not specified, setting to ON is disabled. : Default value ON/OFF ●JOB Specifies whether to send the TRAP at the completion of job printing. When this operation is not set to OFF, TRAP conditions can be specified by TRAP**:IP address or TRAP**:PORT operation. : Default value OFF/ON (IP address)/ON (PORT) Chapter 12 Ethernet parameter "ETHERNET" ●IP ADDR IP address is enabled and can be specified setting when the is selected from the operation TRAP** job menu. When specified IP address is identical to the IP address of the receiving host, TRAP is transmitted to the TRAP manager. When it is set to 000.000.000.000, TRAP is transmitted to all jobs received. 000.000.000.000 to 255.255.255.255 Default value: 000.000.000.000 12-11
- Page 166 and 167: Setting items Allows for setting of
- Page 168 and 169: : Default value A SERIES /9" SERIES
- Page 170 and 171: Setting items Function menu is used
- Page 172 and 173: 8-4 (Sample of print)
- Page 174 and 175: DSCAN SELF PLOT Executes self-plott
- Page 176 and 177: JOB LOG Executes job log print. Pri
- Page 178 and 179: ENGINE LOG Prints the engine inform
- Page 180 and 181: SYSTEM DATE Specifies the date (yea
- Page 183 and 184: ▼Setting items Chapter 9 "PROTOCO
- Page 185 and 186: ▼Setting items PDL SELECT This de
- Page 187: ▼Setting items USER NAME Specifie
- Page 190 and 191: Reset functions The reset menu is u
- Page 192 and 193: Setting items After this menu is ch
- Page 194 and 195: ■Scanner ●DELIVERY HOST IP ADDR
- Page 196 and 197: ■USB Specifies the USB interface
- Page 198 and 199: A SERIES ROLL A0 (841 mm / 33.1 inc
- Page 200 and 201: ■Each size paper of each series S
- Page 202 and 203: SCAN START Allows for determining w
- Page 204 and 205: LANGUAGE Switches the message displ
- Page 206 and 207: ◆ If the [Enter] key is pressed w
- Page 208 and 209: Setting items Ethernet parameter is
- Page 210 and 211: PORT SELECT Selects the Ethernet po
- Page 212 and 213: ROUTING TABLE Specifies the routing
- Page 214 and 215: ■METRIC Specifies the metric. 1
- Page 218 and 219: ●PORT Port is enabled and can be
- Page 220 and 221: About Terioplot The Terioplot softw
- Page 222 and 223: Settings In order to operate the pl
- Page 225 and 226: Chapter 14 Troubleshooting Chapter
- Page 227 and 228: When an error message appears When
- Page 229 and 230: ▼When an error message appears 3
- Page 231 and 232: ▼When an error message appears
- Page 233 and 234: ▼When an error message appears 3
- Page 235 and 236: ▼When an error message appears
- Page 237 and 238: ▼When an error message appears 5
- Page 239 and 240: ▼When an error message appears
- Page 241 and 242: ▼When an error message appears
- Page 243 and 244: ▼When an error message appears Op
- Page 245 and 246: ▼When an error message appears W
- Page 247 and 248: ▼When an error message appears
- Page 249 and 250: ▼When an error message appears (4
- Page 251 and 252: ▼When an error message appears (5
- Page 253 and 254: ▼When an error message appears (1
- Page 255 and 256: ▼When an error message appears (2
- Page 257 and 258: ▼When an error message appears
- Page 259 and 260: ▼When an error message appears
- Page 261 and 262: ▼When an error message appears (6
- Page 263 and 264: ▼When an error message appears (1
- Page 265 and 266: Error log ▼When an error message
▼Setting items<br />
●ERROR<br />
Specifies whether to transmit the TRAP if an engine-related error occurs<br />
(except for technical call error).<br />
When an error occurs, TRAP is sent to the TRAP manager which was<br />
specified in the TRAP manager described above.<br />
If the TRAP manager item is not specified, setting to ON is disabled.<br />
: Default value<br />
ON/OFF<br />
●JOB<br />
Specifies whether to send the TRAP at the completion of job printing.<br />
When this operation is not set to OFF, TRAP conditions can be specified<br />
by TRAP**:IP address or TRAP**:PORT operation.<br />
: Default value<br />
OFF/ON (IP address)/ON (PORT)<br />
Chapter 12 Ethernet parameter "ETHERNET"<br />
●IP ADDR<br />
IP address is enabled and can be specified setting when the is selected from the operation TRAP** job menu. When<br />
specified IP address is identical to the IP address of the receiving host,<br />
TRAP is transmitted to the TRAP manager. When it is set to<br />
000.000.000.000, TRAP is transmitted to all jobs received.<br />
<br />
000.000.000.000 to 255.255.255.255<br />
Default value: 000.000.000.000<br />
12-11