1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
Setting items Ethernet parameter is an item in the system menu. After this menu is changed, the parameter is automatically saved and the system is reset. When there is a job standing for processing, you can only refer to this menu. If you only refer to the menu and do not change it, the system returns to the offline condition. Menu Third hierarchy item Fourth hierarchy item Fifth hierarchy item Parameter #PORT SELECT 1-10 >XLF-------- Choice input method N ote 1) (X, L, F, - ) #DHCP > DISABLE DISABLE ENABLE #IP ADDRESS >000.000.000.000 (Note 2, 6) I nput value #SUBNET MASK >000.000.000.000 (Note 6) I nput value #ROUTING TABLE #GATEWAY ADDR 01 >000.000.000.000 #NETWORK ADDR 01 >000.000.000.000 (Note 6) I nput value (Note 3, 6) I nput value #GATEWAY ADDR 02 >000.000.000.000 (Note 6) I nput value #NETWORK ADDR 02 >000.000.000.000 (Note 3, 6) I nput value #ROUTING TABLE 2 : : COMM.PARAM # ETHERNET #GATEWAY ADDR 10 >000.000.000.000 (Note 6) I nput value #NETWORK ADDR 10 >000.000.000.000 (Note 3, 6) I nput value #METRIC >064 Input value 1 to 255 #SETUP DETAILS #ETHERNET ADDR >0800832Annnn Reference only nnn: serial No. #CONNECTION SPD. >AUTO AUTO 100 10 #CONNECTION TYPE >AUTO AUTO FULL HALF #HTTP PORT >00080 Input value 0 to 65535 #PORT TIME OUT >30min OFF 5min 10min 15min 30min 12-2
▼Setting items Menu Third hierarchy item Fourth hierarchy item Fifth hierarchy item Parameter COMM.PARAM # ETHERNET #SETUP DETAILS #FTP DATA TYPE >ASCII/BIN #SNMP >OFF #SNMP VERSION >V1 #TRAP01 #TRAP02 #MANEGER >000.000.000.000 #ERROR >ON #JOB >OFF #IP ADDR >000.000.000.000 #PORT >ALL #MANAGER >000.000.000.000 #ERROR >ON #JOB >OFF #IP ADDR >000.000.000.000 #PORT >ALL Note 1) Up to 10 ports including XPT, LPD, FTP can be specified. The initial value is 1 port for each protocol.(XLF – – – – – – –) Setting example: # PORT SELECT 1-10 >FFFXXXLLL_ ......In case of 3 ports for each protocol. Note 2) Same as the IP address specified in the installing operation. Note 3) Network address is indicated only when the "Gateway address" is specified. Note 4) To be displayed only when the "TRAPnn job" is set to ON (IP address). Note 5) To be displayed only when the "TRAPnn job" is set to ON (PORT). Note 6) Not to be displayed when "DHCP" is set to enable. ASCII/BIN BIN OFF ON V1 V2 Choice input method ON OFF OFF ON (IP ADDRESS) ON (PORT) C (Note 4) hoice input method (Note 5) A LL PORT01 ⋅ PORT10 Choice input method ON OFF OFF ON (IP ADDRESS) ON (PORT) C (Note 4) hoice input method (Note 5) A LL PORT01 ⋅ PORT10 Chapter 12 Ethernet parameter "ETHERNET" 12-3
- Page 158 and 159: RASTER PARAM This is a parameter gr
- Page 160 and 161: Setting items Operating conditions
- Page 162 and 163: EDGE CUT TIMER When you plot data r
- Page 164 and 165: DOCSET TIME (sec) Allows for settin
- Page 166 and 167: Setting items Allows for setting of
- Page 168 and 169: : Default value A SERIES /9" SERIES
- Page 170 and 171: Setting items Function menu is used
- Page 172 and 173: 8-4 (Sample of print)
- Page 174 and 175: DSCAN SELF PLOT Executes self-plott
- Page 176 and 177: JOB LOG Executes job log print. Pri
- Page 178 and 179: ENGINE LOG Prints the engine inform
- Page 180 and 181: SYSTEM DATE Specifies the date (yea
- Page 183 and 184: ▼Setting items Chapter 9 "PROTOCO
- Page 185 and 186: ▼Setting items PDL SELECT This de
- Page 187: ▼Setting items USER NAME Specifie
- Page 190 and 191: Reset functions The reset menu is u
- Page 192 and 193: Setting items After this menu is ch
- Page 194 and 195: ■Scanner ●DELIVERY HOST IP ADDR
- Page 196 and 197: ■USB Specifies the USB interface
- Page 198 and 199: A SERIES ROLL A0 (841 mm / 33.1 inc
- Page 200 and 201: ■Each size paper of each series S
- Page 202 and 203: SCAN START Allows for determining w
- Page 204 and 205: LANGUAGE Switches the message displ
- Page 206 and 207: ◆ If the [Enter] key is pressed w
- Page 210 and 211: PORT SELECT Selects the Ethernet po
- Page 212 and 213: ROUTING TABLE Specifies the routing
- Page 214 and 215: ■METRIC Specifies the metric. 1
- Page 216 and 217: ■FTP DATA TYPE Specifies the init
- Page 218 and 219: ●PORT Port is enabled and can be
- Page 220 and 221: About Terioplot The Terioplot softw
- Page 222 and 223: Settings In order to operate the pl
- Page 225 and 226: Chapter 14 Troubleshooting Chapter
- Page 227 and 228: When an error message appears When
- Page 229 and 230: ▼When an error message appears 3
- Page 231 and 232: ▼When an error message appears
- Page 233 and 234: ▼When an error message appears 3
- Page 235 and 236: ▼When an error message appears
- Page 237 and 238: ▼When an error message appears 5
- Page 239 and 240: ▼When an error message appears
- Page 241 and 242: ▼When an error message appears
- Page 243 and 244: ▼When an error message appears Op
- Page 245 and 246: ▼When an error message appears W
- Page 247 and 248: ▼When an error message appears
- Page 249 and 250: ▼When an error message appears (4
- Page 251 and 252: ▼When an error message appears (5
- Page 253 and 254: ▼When an error message appears (1
- Page 255 and 256: ▼When an error message appears (2
- Page 257 and 258: ▼When an error message appears
Setting items<br />
Ethernet parameter is an item in the system menu. After this menu is<br />
changed, the parameter is automatically saved and the system is reset.<br />
When there is a job standing for processing, you can only refer to this<br />
menu.<br />
If you only refer to the menu and do not change it, the system returns to<br />
the offline condition.<br />
Menu<br />
Third hierarchy item<br />
Fourth hierarchy item<br />
Fifth hierarchy item<br />
Parameter<br />
#PORT SELECT 1-10<br />
>XLF--------<br />
Choice input method<br />
N ote 1)<br />
(X, L, F, - )<br />
#DHCP<br />
> DISABLE<br />
DISABLE<br />
ENABLE<br />
#IP ADDRESS<br />
>000.000.000.000<br />
(Note 2, 6)<br />
I nput value<br />
#SUBNET MASK<br />
>000.000.000.000<br />
(Note 6)<br />
I nput value<br />
#ROUTING TABLE<br />
#GATEWAY ADDR 01<br />
>000.000.000.000<br />
#NETWORK ADDR 01<br />
>000.000.000.000<br />
(Note 6)<br />
I nput value<br />
(Note 3, 6)<br />
I nput value<br />
#GATEWAY ADDR 02<br />
>000.000.000.000<br />
(Note 6)<br />
I nput value<br />
#NETWORK ADDR 02<br />
>000.000.000.000<br />
(Note 3, 6)<br />
I nput value<br />
#ROUTING TABLE 2<br />
:<br />
:<br />
COMM.PARAM<br />
# ETHERNET<br />
#GATEWAY ADDR 10<br />
>000.000.000.000<br />
(Note 6)<br />
I nput value<br />
#NETWORK ADDR 10<br />
>000.000.000.000<br />
(Note 3, 6)<br />
I nput value<br />
#METRIC<br />
>064<br />
Input value<br />
1 to 255<br />
#SETUP DETAILS<br />
#ETHERNET ADDR<br />
>0800832Annnn<br />
Reference only<br />
nnn: serial No.<br />
#CONNECTION SPD.<br />
>AUTO<br />
AUTO<br />
100<br />
10<br />
#CONNECTION TYPE<br />
>AUTO<br />
AUTO<br />
FULL<br />
HALF<br />
#HTTP PORT<br />
>00080<br />
Input value<br />
0 to 65535<br />
#PORT TIME OUT<br />
>30min<br />
OFF<br />
5min<br />
10min<br />
15min<br />
30min<br />
12-2