1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
■Each size paper of each series Specifies whether to use each size paper of the series. A SERIES /9" SERIES /8.5" SERIES /30×42 SERIES / MAP SERIES / DIN SERIES / CHINA SERIES : Default value OFF/ON Notes ◆ The default value varies the INITIAL SETTING. ◆ This item is displayed only for choices which are ON in the ENABLE SERIES of the system menu. ◆ All of the parameters of the same series cannot be set to OFF. ◆ When a roll of each series is loaded into this device, that parameter automatically turns ON. 11-10
▼Setting items CHINA SIZE Specifies the roll size of the Chinese series handled by this device. SYSTEM #CHINA SIZE Menu Second hierarchy item Parameter #CHINA A0 >914 mm (36 inches) #CHINA A1 >620 mm (24.4 inches) #CHINA A2 >450 mm (17.7 inches) #CHINA A3 >310 mm (12.2 inches) 914 mm (36 inches) 910 mm (35.8 inches) 900 mm (35.4 inches) 880 mm (34.6 inches) 620 mm (24.4 inches) 610 mm (24 inches) 450 mm (17.7 inches) 440 mm (17.3 inches) 310 mm (12.2 inches) Chapter 11 "SYSTEM" menu ■Each size paper of Chinese series Specifies the paper size from A0 to A3 of the Chinese series. Note ◆ This item is displayed only when the CHINESE SERIES of the ENABLE SERIES in the system menu is ON. 11-11
- Page 150 and 151: ■PLAN SIZE (HP-GL only) Sets whic
- Page 152 and 153: Manual feed + two-step roll model P
- Page 154 and 155: Specified value (mm (inch)) No. of
- Page 156 and 157: The joints can be specified with th
- Page 158 and 159: RASTER PARAM This is a parameter gr
- Page 160 and 161: Setting items Operating conditions
- Page 162 and 163: EDGE CUT TIMER When you plot data r
- Page 164 and 165: DOCSET TIME (sec) Allows for settin
- Page 166 and 167: Setting items Allows for setting of
- Page 168 and 169: : Default value A SERIES /9" SERIES
- Page 170 and 171: Setting items Function menu is used
- Page 172 and 173: 8-4 (Sample of print)
- Page 174 and 175: DSCAN SELF PLOT Executes self-plott
- Page 176 and 177: JOB LOG Executes job log print. Pri
- Page 178 and 179: ENGINE LOG Prints the engine inform
- Page 180 and 181: SYSTEM DATE Specifies the date (yea
- Page 183 and 184: ▼Setting items Chapter 9 "PROTOCO
- Page 185 and 186: ▼Setting items PDL SELECT This de
- Page 187: ▼Setting items USER NAME Specifie
- Page 190 and 191: Reset functions The reset menu is u
- Page 192 and 193: Setting items After this menu is ch
- Page 194 and 195: ■Scanner ●DELIVERY HOST IP ADDR
- Page 196 and 197: ■USB Specifies the USB interface
- Page 198 and 199: A SERIES ROLL A0 (841 mm / 33.1 inc
- Page 202 and 203: SCAN START Allows for determining w
- Page 204 and 205: LANGUAGE Switches the message displ
- Page 206 and 207: ◆ If the [Enter] key is pressed w
- Page 208 and 209: Setting items Ethernet parameter is
- Page 210 and 211: PORT SELECT Selects the Ethernet po
- Page 212 and 213: ROUTING TABLE Specifies the routing
- Page 214 and 215: ■METRIC Specifies the metric. 1
- Page 216 and 217: ■FTP DATA TYPE Specifies the init
- Page 218 and 219: ●PORT Port is enabled and can be
- Page 220 and 221: About Terioplot The Terioplot softw
- Page 222 and 223: Settings In order to operate the pl
- Page 225 and 226: Chapter 14 Troubleshooting Chapter
- Page 227 and 228: When an error message appears When
- Page 229 and 230: ▼When an error message appears 3
- Page 231 and 232: ▼When an error message appears
- Page 233 and 234: ▼When an error message appears 3
- Page 235 and 236: ▼When an error message appears
- Page 237 and 238: ▼When an error message appears 5
- Page 239 and 240: ▼When an error message appears
- Page 241 and 242: ▼When an error message appears
- Page 243 and 244: ▼When an error message appears Op
- Page 245 and 246: ▼When an error message appears W
- Page 247 and 248: ▼When an error message appears
- Page 249 and 250: ▼When an error message appears (4
■Each size paper of each series<br />
Specifies whether to use each size paper of the series.<br />
A SERIES /9" SERIES /8.5" SERIES /30×42 SERIES /<br />
MAP SERIES / DIN SERIES / CHINA SERIES<br />
: Default value<br />
OFF/ON<br />
Notes<br />
◆ The default value varies the INITIAL SETTING.<br />
◆ This item is displayed only for choices which are ON in the<br />
ENABLE SERIES of the system menu.<br />
◆ All of the parameters of the same series cannot be set to<br />
OFF.<br />
◆ When a roll of each series is loaded into this device, that<br />
parameter automatically turns ON.<br />
11-10