1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
■SCALE X (%) SCALE Y (%) When setting "SCALE MODE = MANUAL SCALE," values of the scale applied to X and Y directions of the drawing are set up. This setting is performed on the third hierarchy. 0.01 to 1000.00 Default value = 100 This setting is enabled when setting "SCALE MODE = MANUAL SCALE." When it is set to 100%, the plot is produced in 1-to-1 magnification. ■PEN WIDTH SCALE (HP-GL, DSCAN only) Sets the scaling down method, when the drawing is scaled down (in the same X and Y proportion). This setting is performed on the third hierarchy. : Default value ON Line width or interval between points are also scaled down. Maximum line width is 16 mm (0.63 inches). OFF Line width or interval between points are not scaled down. ■FIX SCALE A FIX SCALE 9" FIX SCALE 8.5" Allows for setting the method of automatic scale from one fixed form to another when setting "SCALE MODE = MANUAL SCALE." This setting is disabled when plotting in the actual length or expanded fixed form. This setting is performed on the third hierarchy. 5-22
▼Setting parameter items FIX SCALE A Automatically scaled to A4 fix size. Automatically scaled to A3 fix size. Automatically scaled to A2 fix size. Automatically scaled to A1 fix size. Automatically scaled to A0 fix size. FIX SCALE 9" A Automatically scaled to 9×12 inch series A fix size. B Automatically scaled to 9×12 inch series B fix size. C Automatically scaled to 9×12 inch series C fix size. D Automatically scaled to 9×12 inch series D fix size. E Automatically scaled to 9×12 inch series E fix size. FIX SCALE 8.5" A Automatically scaled to 8.5 × 11 inch series A fix size. B Automatically scaled to 8.5 × 11 inch series B fix size. C Automatically scaled to 8.5 × 11 inch series C fix size. D Automatically scaled to 8.5 × 11 inch series D fix size. E Automatically scaled to 8.5 × 11 inch series E fix size. Chapter 5 "SETUP" Menu 5-23
- Page 96 and 97: Channels and ports This device is e
- Page 98 and 99: Jobs The device manages the receive
- Page 100 and 101: (1) Setup menu Change the settings
- Page 102 and 103: PDL menu The various print paramete
- Page 104 and 105: Printing status Me nu Mo de MENU #S
- Page 106 and 107: Device menu “DEVICE” From the d
- Page 108 and 109: Function menu “FUNCTION” Press
- Page 110 and 111: Reset menu “RESET” Press the [
- Page 113 and 114: Chapter 4 Basic Menu Operation Chap
- Page 115 and 116: Offline menu operation Press the [M
- Page 117 and 118: ▼Offline menu operation Setting o
- Page 119 and 120: ▼Offline menu operation ■Numeri
- Page 121 and 122: ▼Offline menu operation ■Execut
- Page 123: ▼Offline menu operation Exiting t
- Page 126 and 127: Setting parameter items The followi
- Page 128 and 129: (A) Second hierarchy item ✽ Third
- Page 130 and 131: 5-6 (D-1) item ourth hierarchy F r
- Page 132 and 133: (E) Third hierarchy item Parameter
- Page 134 and 135: (G) Third hierarchy item Parameter
- Page 136 and 137: AUTO SUPPLY Allows for setting the
- Page 138 and 139: : Default value FIX SIZE Produces f
- Page 140 and 141: ■SIZE MARGIN (mm) / SIZE MARGIN (
- Page 142 and 143: ■MARGIN (mm) / MARGIN (in) Allows
- Page 144 and 145: ■REVERSE (TIFF, CALS only) Allows
- Page 148 and 149: FORMAT PARAM. (HP-GL DSCAN only) Th
- Page 150 and 151: ■PLAN SIZE (HP-GL only) Sets whic
- Page 152 and 153: Manual feed + two-step roll model P
- Page 154 and 155: Specified value (mm (inch)) No. of
- Page 156 and 157: The joints can be specified with th
- Page 158 and 159: RASTER PARAM This is a parameter gr
- Page 160 and 161: Setting items Operating conditions
- Page 162 and 163: EDGE CUT TIMER When you plot data r
- Page 164 and 165: DOCSET TIME (sec) Allows for settin
- Page 166 and 167: Setting items Allows for setting of
- Page 168 and 169: : Default value A SERIES /9" SERIES
- Page 170 and 171: Setting items Function menu is used
- Page 172 and 173: 8-4 (Sample of print)
- Page 174 and 175: DSCAN SELF PLOT Executes self-plott
- Page 176 and 177: JOB LOG Executes job log print. Pri
- Page 178 and 179: ENGINE LOG Prints the engine inform
- Page 180 and 181: SYSTEM DATE Specifies the date (yea
- Page 183 and 184: ▼Setting items Chapter 9 "PROTOCO
- Page 185 and 186: ▼Setting items PDL SELECT This de
- Page 187: ▼Setting items USER NAME Specifie
- Page 190 and 191: Reset functions The reset menu is u
- Page 192 and 193: Setting items After this menu is ch
- Page 194 and 195: ■Scanner ●DELIVERY HOST IP ADDR
■SCALE X (%)<br />
SCALE Y (%)<br />
When setting "SCALE MODE = MANUAL SCALE," values of the scale<br />
applied to X and Y directions of the drawing are set up.<br />
This setting is performed on the third hierarchy.<br />
<br />
0.01 to 1000.00 Default value = 100<br />
This setting is enabled when setting "SCALE MODE = MANUAL<br />
SCALE." When it is set to 100%, the plot is produced in 1-to-1<br />
magnification.<br />
■PEN WIDTH SCALE (HP-GL, DSCAN only)<br />
Sets the scaling down method, when the drawing is scaled down (in the<br />
same X and Y proportion). This setting is performed on the third<br />
hierarchy.<br />
: Default value<br />
ON<br />
Line width or interval between points are also scaled down.<br />
Maximum line width is 16 mm (0.63 inches).<br />
OFF<br />
Line width or interval between points are not scaled down.<br />
■FIX SCALE A<br />
FIX SCALE 9"<br />
FIX SCALE 8.5"<br />
Allows for setting the method of automatic scale from one fixed form to<br />
another when setting "SCALE MODE = MANUAL SCALE." This<br />
setting is disabled when plotting in the actual length or expanded fixed<br />
form. This setting is performed on the third hierarchy.<br />
5-22