1 - Seiko I Infotech Inc.
1 - Seiko I Infotech Inc. 1 - Seiko I Infotech Inc.
Supplied components The components, including options, which are included in this device can be attached to the main unit at the time of device installation. Confirm that the following components are supplied. If any components are missing or broken, contact your retailer or your nearest service center. Basic components ◆ Plotter unit (1 unit): Built-in system firmware, comes with power cord. ◆ Process cartridge (1 set) Accessories ◆ Roll paper (A0, A1, A3 × 1 unit each, for checking at the time of installation) ◆ Paper flange: 2 to 6 units depending on the paper feeding system. ◆ Toner cartridge (3 units, for checking at time of installation) ◆ Waste bottle (pre-installed, 1 unit) ◆ User's Guide (this Manual and the Copy Instruction Manual (separate) : 1 copy each) Options ◆ Expansion kit (HDD&I/F) (1 unit): Provided for LP-1010L as a standard supply. (for only customers in Japan) ◆ Tray (1 unit) ◆ High-performance stacker (1 unit) (under development) ◆ Scanner exit guide x
TABLE OF CONTENTS Introduction .......................................................................................... i Safety Precautions .............................................................................. ii Warning labels .................................................................................... v How to read this manual ................................................................... vii Manual make-up ................................................................... vii Notation method ...................................................................viii DSCAN format ......................................................................viii Supplied components ......................................................................... x Chapter 1 Getting started 1-1 Features...........................................................................................1-2 Operating conditions ........................................................................1-4 Environmental conditions ....................................................1-4 Installation space .................................................................1-6 Supported ............................................................................1-7 Spool memory configuration ..............................................1-10 The names and functions of each part .......................................... 1-11 Front .................................................................................. 1-11 Right side/rear side ...........................................................1-12 Interior ...............................................................................1-13 Control panel .....................................................................1-14 How to read the status displays for this device..............................1-19 CONTENTS-1
- Page 1: User's Guide (Plotter Unit) Network
- Page 5 and 6: Introduction Thank you for purchasi
- Page 7 and 8: Warning DO NOT touch any of the par
- Page 9 and 10: Warning labels Warning labels are a
- Page 11 and 12: How to read this manual Manual make
- Page 13: Key/LCD/LED notations [ ] Indicates
- Page 17 and 18: Manual paper feeding (cut paper) ..
- Page 19 and 20: Chapter 5 "SETUP" Menu 5-1 Setting
- Page 21 and 22: Chapter 10 "RESET" menu 10-1 Reset
- Page 23: When a print error occurs .........
- Page 26 and 27: Features This device is an electrop
- Page 28 and 29: Operating conditions This section c
- Page 30 and 31: Installation space ■Installation/
- Page 32 and 33: The following roll paper of the wid
- Page 34 and 35: Paper storing precautions are as fo
- Page 36 and 37: Right side/rear side 1 Mai
- Page 38 and 39: NON-PROPORTIONAL Control panel The
- Page 40 and 41: 5 This button turns on/off the powe
- Page 42 and 43: How to read the status displays for
- Page 44 and 45: Warming up display Warmi ng up nnn
- Page 46 and 47: Plotting procedures overview Plotti
- Page 48 and 49: Power on 1 Turn on the Main power s
- Page 50 and 51: Power off When turning the power of
- Page 52 and 53: ■Turning on the power Initial izi
- Page 54 and 55: Online and offline The device is
- Page 56 and 57: If an error message about paper sup
- Page 58 and 59: How to detach the paper rolls 1 Pul
- Page 60 and 61: E How to attach the paper roll ◆
- Page 62 and 63: 6 Close the paper roll drawer. Gent
Supplied components<br />
The components, including options, which are included in this device can<br />
be attached to the main unit at the time of device installation. Confirm<br />
that the following components are supplied.<br />
If any components are missing or broken, contact your retailer or your<br />
nearest service center.<br />
Basic components<br />
◆ Plotter unit (1 unit): Built-in system firmware, comes with power<br />
cord.<br />
◆ Process cartridge (1 set)<br />
Accessories<br />
◆ Roll paper (A0, A1, A3 × 1 unit each, for checking at the time of<br />
installation)<br />
◆ Paper flange: 2 to 6 units depending on the paper feeding system.<br />
◆ Toner cartridge (3 units, for checking at time of installation)<br />
◆ Waste bottle (pre-installed, 1 unit)<br />
◆ User's Guide (this Manual and the Copy Instruction Manual (separate) :<br />
1 copy each)<br />
Options<br />
◆ Expansion kit (HDD&I/F) (1 unit): Provided for LP-1010L as a<br />
standard supply.<br />
(for only customers in Japan)<br />
◆ Tray (1 unit)<br />
◆ High-performance stacker (1 unit) (under development)<br />
◆ Scanner exit guide<br />
x