1 - Seiko I Infotech Inc.

More documents

Recommendations

Info

Notation method Markings Warning ◆ This mark indicates warnings that must be followed carefully to avoid serious bodily injury or death. Caution ◆ This mark indicates cautions that must be observed to avoid damage to the equipment and bodily injury. Note ◆ Contain important information. This is a “Tip” mark. Contain additional hints for better use. ⇒ This is a “See” mark. A reference section and page is indicated after this mark. DSCAN format Please remember: The DSCAN format described in this document as well as DSCAN that appears on the operation display are for only customers in Japan. viii
Key/LCD/LED notations [ ] Indicates a control panel key. Indicates the control panel screen. 1 Press [MENU] key to proceed to the menu screen where settings are managed. MENU MODE MENU #SETUP 2 Press [ ] and select “SETUP.” MENU MODE SETUP #PORT1_HPGL 3 Press [ ] or [ ] and select “PORT2_HPGL.” MENU MODE SETUP #PORT2_HPGL Indicates flashing light (On the actual screen, a short vertical line at the upper left of the selected character is flashing. In this manual, the selected character itself is shadowed for its visibility.) LED on, flashing, and off states are indicated as follows: On Flashing Off ix
Page 1: User's Guide (Plotter Unit) Network
Page 5 and 6: Introduction Thank you for purchasi
Page 7 and 8: Warning DO NOT touch any of the par
Page 9 and 10: Warning labels Warning labels are a
Page 11: How to read this manual Manual make
Page 15 and 16: TABLE OF CONTENTS Introduction ....
Page 17 and 18: Manual paper feeding (cut paper) ..
Page 19 and 20: Chapter 5 "SETUP" Menu 5-1 Setting
Page 21 and 22: Chapter 10 "RESET" menu 10-1 Reset
Page 23: When a print error occurs .........
Page 26 and 27: Features This device is an electrop
Page 28 and 29: Operating conditions This section c
Page 30 and 31: Installation space ■Installation/
Page 32 and 33: The following roll paper of the wid
Page 34 and 35: Paper storing precautions are as fo
Page 36 and 37: Right side/rear side 1 Mai
Page 38 and 39: NON-PROPORTIONAL Control panel The
Page 40 and 41: 5 This button turns on/off the powe
Page 42 and 43: How to read the status displays for
Page 44 and 45: Warming up display Warmi ng up nnn
Page 46 and 47: Plotting procedures overview Plotti
Page 48 and 49: Power on 1 Turn on the Main power s
Page 50 and 51: Power off When turning the power of
Page 52 and 53: ■Turning on the power Initial izi
Page 54 and 55: Online and offline The device is
Page 56 and 57: If an error message about paper sup
Page 58 and 59: How to detach the paper rolls 1 Pul
Page 60 and 61: E How to attach the paper roll ◆
Page 62 and 63:
6 Close the paper roll drawer. Gent
Page 64 and 65:
Precautions on handling Warning Do
Page 66 and 67:
3 Close the scanner cover. Stopper
Page 68 and 69:
8 Pull the lever to the right end.
Page 70 and 71:
Replacing the waste toner bottle Wh
Page 72 and 73:
3 Remove the waste toner bottle fro
Page 74 and 75:
Replacing the process cartridge Whe
Page 76 and 77:
2 Take out the Process cartridge. P
Page 78 and 79:
6 Insert the Process cartridge. To
Page 80 and 81:
Manual paper feeding (cut paper) Th
Page 82 and 83:
9× 12 series fixed form cut paper
Page 84 and 85:
When feeding the cut paper into the
Page 86 and 87:
Cancel printing Press the [STOP] ke
Page 88 and 89:
Web function startup method 1 The f
Page 90 and 91:
Using paper of new standard series
Page 92 and 93:
Using paper of Chinese standard ser
Page 94 and 95:
Limiting rolls to be used When limi
Page 96 and 97:
Channels and ports This device is e
Page 98 and 99:
Jobs The device manages the receive
Page 100 and 101:
(1) Setup menu Change the settings
Page 102 and 103:
PDL menu The various print paramete
Page 104 and 105:
Printing status Me nu Mo de MENU #S
Page 106 and 107:
Device menu “DEVICE” From the d
Page 108 and 109:
Function menu “FUNCTION” Press
Page 110 and 111:
Reset menu “RESET” Press the [
Page 113 and 114:
Chapter 4 Basic Menu Operation Chap
Page 115 and 116:
Offline menu operation Press the [M
Page 117 and 118:
▼Offline menu operation Setting o
Page 119 and 120:
▼Offline menu operation ■Numeri
Page 121 and 122:
▼Offline menu operation ■Execut
Page 123:
▼Offline menu operation Exiting t
Page 126 and 127:
Setting parameter items The followi
Page 128 and 129:
(A) Second hierarchy item ✽ Third
Page 130 and 131:
5-6 (D-1) item ourth hierarchy F r
Page 132 and 133:
(E) Third hierarchy item Parameter
Page 134 and 135:
(G) Third hierarchy item Parameter
Page 136 and 137:
AUTO SUPPLY Allows for setting the
Page 138 and 139:
: Default value FIX SIZE Produces f
Page 140 and 141:
■SIZE MARGIN (mm) / SIZE MARGIN (
Page 142 and 143:
■MARGIN (mm) / MARGIN (in) Allows
Page 144 and 145:
■REVERSE (TIFF, CALS only) Allows
Page 146 and 147:
■SCALE X (%) SCALE Y (%) When set
Page 148 and 149:
FORMAT PARAM. (HP-GL DSCAN only) Th
Page 150 and 151:
■PLAN SIZE (HP-GL only) Sets whic
Page 152 and 153:
Manual feed + two-step roll model P
Page 154 and 155:
Specified value (mm (inch)) No. of
Page 156 and 157:
The joints can be specified with th
Page 158 and 159:
RASTER PARAM This is a parameter gr
Page 160 and 161:
Setting items Operating conditions
Page 162 and 163:
EDGE CUT TIMER When you plot data r
Page 164 and 165:
DOCSET TIME (sec) Allows for settin
Page 166 and 167:
Setting items Allows for setting of
Page 168 and 169:
: Default value A SERIES /9" SERIES
Page 170 and 171:
Setting items Function menu is used
Page 172 and 173:
8-4 (Sample of print)
Page 174 and 175:
DSCAN SELF PLOT Executes self-plott
Page 176 and 177:
JOB LOG Executes job log print. Pri
Page 178 and 179:
ENGINE LOG Prints the engine inform
Page 180 and 181:
SYSTEM DATE Specifies the date (yea
Page 183 and 184:
▼Setting items Chapter 9 "PROTOCO
Page 185 and 186:
▼Setting items PDL SELECT This de
Page 187:
▼Setting items USER NAME Specifie
Page 190 and 191:
Reset functions The reset menu is u
Page 192 and 193:
Setting items After this menu is ch
Page 194 and 195:
■Scanner ●DELIVERY HOST IP ADDR
Page 196 and 197:
■USB Specifies the USB interface
Page 198 and 199:
A SERIES ROLL A0 (841 mm / 33.1 inc
Page 200 and 201:
■Each size paper of each series S
Page 202 and 203:
SCAN START Allows for determining w
Page 204 and 205:
LANGUAGE Switches the message displ
Page 206 and 207:
◆ If the [Enter] key is pressed w
Page 208 and 209:
Setting items Ethernet parameter is
Page 210 and 211:
PORT SELECT Selects the Ethernet po
Page 212 and 213:
ROUTING TABLE Specifies the routing
Page 214 and 215:
■METRIC Specifies the metric. 1
Page 216 and 217:
■FTP DATA TYPE Specifies the init
Page 218 and 219:
●PORT Port is enabled and can be
Page 220 and 221:
About Terioplot The Terioplot softw
Page 222 and 223:
Settings In order to operate the pl
Page 225 and 226:
Chapter 14 Troubleshooting Chapter
Page 227 and 228:
When an error message appears When
Page 229 and 230:
▼When an error message appears 3
Page 231 and 232:
▼When an error message appears
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
▼When an error message appears Op
Page 245 and 246:
▼When an error message appears W
Page 247 and 248:
Page 249 and 250:
▼When an error message appears (4
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Error log ▼When an error message
Page 267 and 268:
▼Error log Type of Error Log The
Page 269 and 270:
▼Error log Error Log Classificati
Page 271 and 272:
▼Troubleshooting for ethernet Cau
Page 273 and 274:
When a print error occurs This sect
Page 275 and 276:
▼ Basic Specifications Appendix A
Page 277 and 278:
▼ Basic specifications (2/2) Item
Page 279 and 280:
▼ Menu structure A Note ( 5 ) TIF
Page 281 and 282:
▼ Menu structure C C' Note ( 7 )
Page 283 and 284:
▼ Menu structure E E' #PEN PARAME
Page 285 and 286:
▼ Menu structure [PAPER] MENU MEN
Page 287 and 288:
○ ○ ○ ○ ▼ Menu structure
Page 289 and 290:
▼ Menu structure [SYSTEM] MENU ME
Page 291 and 292:
▼ Menu structure H SYSTEM #APPLY
Page 293 and 294:
▼ Menu structure J #SCAN START >O
Page 295 and 296:
▼ Menu structure L #CONNECTION TY
Page 297 and 298:
▼ Command list HP-GL,HP-GL/2 Devi
Page 299 and 300:
▼ Command list Advanced instructi
Page 301 and 302:
▼ Command list Foreground Render
Page 303 and 304:
▼ Command list (2/6) Classificati
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
▼ Command list CALS Format Record
Page 311:
▼ Command list lpd Support Comman
show all

1 - Seiko I Infotech Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?