Download - Industrial and Bearing Supplies

DuraRAY ® Phase II
LED Warning Beacons
l Amber LED
l Yellow Base
l Red LED
l Yellow Base
l Green LED
l Yellow Base
l Amber LED
l Amber Base
l Red LED
l Amber Base
l Green LED
l Amber Base
2 LED Disks HM9400YEL2A HM9400YEL2R HM9400YEL2G HM9400AMB2A HM9400AMB2R HM9400AMB2G
3 LED Disks HM9400YEL3A HM9400YEL3R HM9400YEL3G HM9400AMB3A HM9400AMB3R HM9400AMB3G
4 LED Disks HM9400YEL4A HM9400YEL4R HM9400YEL4G HM9400AMB4A HM9400AMB4R HM9400AMB4G
LED BEACONS
MOBILE BEACONS EQUIPMENT
LIGHTING
40
®
DuraRAY
LED Warning Beacons
Phase II
Hella DuraRAY ® II ultra durable LED warning
beacons improve on the award winning design
of its predecessor. DuraRAY ® II beacons are
designed for mining and construction applications
where the cost of equipment down time is large
and safety is paramount.
130.6
130.6
153.5
132.5
159
3 x Ø6
equispaced
on PCD Ø150
3 x M4
equispaced
on PCD Ø107
3 x M4
equispaced
on PCD Ø130
25mm Pipe Thread
169
130.6
111.5
2 LED Disks
3 LED Disks
4 LED Disks
The cast alloy construction and
modular lens design enables
DuraRAY ® II beacons to survive
much larger crush or impact
loads than conventional optical
beacons. DuraRAY ® II beacons
offer excellent beam control to
ensure very good penetration of
fog and dust without blinding the
operator through back scatter,
whilst delivering high observability
from a distance with minimal closeup
glare.
Solid state LED beacons are
gaining popularity due to their
zero maintenance and long
service life over conventional
rotating beacons, particularly
in harsh mining conditions. The
new range of DuraRAY ® II LED
warning beacons build on an
award winning design with the
addition of a new electronic control
system, combined with higher
output LEDs, and further user
customisation within the range.
Higher EMC standard ISO13766-
2006 certification improves safety
and reliability with other electrical
devices. Coloured secondary
reflectors were added to ensure
easy identification of LED function
colour when the beacon is in ‘off’
mode.
Using an advanced control system
gives users the option to select
from a flashing
or rotating LED
beam pattern by
simply changing
the polarity of
the two wires.
The Multivolt
system allows
for installation on
electrical machines that
may have varying outputs due
to the load on the engine.
The light output from the high
emitting LEDs is not affected by
this varying supply, with a range
of 9-33 Volts DC.
The increased light output from
the LEDs combined with multiple
layers of LEDs delivers a high
degree of redundancy in the
optical system to ensure safety
is not compromised under partial
failure or obscuring conditions.
Utilising ceramic coated aluminium
reflectors and durable XYLEX ®
lenses provides excellent longterm
resistance against cleaning
chemicals, UV and impact damage
for increased durability and long
service life.
DuraRAY ® II beacons are fully
sealed ‘fit and forget’ products
that can be submerged and
high-pressure washed from any
direction.
Product features
Multivolt 9-33V DC
New electronics offer
both ‘rotating’ and
flashing functionality
Modular system of
circular LED discs for
intense, 360˚ visible
light output
Brilliant clear, high
impact resistant
XYLEX ® lens system
Heavy-duty cast alloy
base and cap for
increased mechanical
strength and vibration
resistance
Multi-stage paint
coating for optimal
corrosion and UV
protection
ISO 13766-2006
Flame retardant to
UL94HB
Fully sealed and
pre-wired to prevent
ingress of dirt and
moisture
200G shock resistant
Low EMC signature
Low current draw
Self-diagnostic
electronics for
protection against
transient voltage spikes
and reverse polarity
LED Function colour
variants available
(Amber, Green, Red)
Spare Parts
9.HM9386.02
Installation Kit
MULTI
VOLT
LED
DT &
BARE
WIRE
IP6K7
200G
9 to 33
V DC
33W
MAX