Agilent FieldFox RF Analyzer N9912A - Tessco

More documents

Recommendations

Info

General Information (continued) Description Specification Typical Supplemental Information Inputs & Outputs RF Out Port Connector Impedance Damage Level RF In Port Connector Impedance Damage Level LO Emissions 0 dB attenuation, preamplifier off Headphone Jack Connector USB LAN Type–N, female 50 Ω (nominal) > +23 dBm, > ±50 VDC Type–N, female 50 Ω (nominal) > +27 dBm, > ±50 VDC 3.5 mm (1/8 inch) miniature audio jack USB–A (2 ports) Hi–speed USB 2.0 –65 dBm (nominal) Mini USB (1 port) Hi–speed USB 2.0 Provided for future use. External Reference /Trigger Input Connector External Reference Input Frequency Input Amplitude Range Impedance Lock Range Trigger Input Impedance Level Range Rising Edge Falling Edge 100Base-T ONLY RJ–45 connector BNC female 10 MHz 10Base-T is NOT supported –5 dBm to +10 dBm (nominal) 50 Ω (nominal) ±10 ppm of external reference frequency (nominal) 10 KΩ (nominal) 1.7 V (nominal) 1 V (nominal) 1 Samples of this product have been type tested in accordance with the Agilent Environmental Test Manual (ETM) for outdoor equipment (OE) and verified to be robust against the environmental stresses of storage, transportation and end use ; those stresses include but are not limited to temperature, humidity, shock, vibration, altitude and power line conditions. 2 Charge and discharge temperatures are internal temperatures of the battery as measured by a sensor embedded in the battery. The Battery screen displays temperature information. To access the screen, select System , Service Diagnostics, and Battery. 24
Supported Cal Kits The following list of calibration kits are loaded in the FieldFox. You can add additional calibration kits to the FieldFox using FieldFox Data Link Software. The basic QuickCal does not require cal standards. However, for higher accuracy, perform QuickCal with a load. Description N9910X-800 N9910X-801 N9910X-802 N9910X-803 85031B 85032E 85032F 85033E 85036B 85036E Supplemental Information T-calibration kit, DC-6 GHz, Type-N(m) T-calibration kit, DC-6 GHz, Type-N(f) T-calibration kit, DC-6 GHz, 7/16 DIN(m) T-calibration kit, DC-6 GHz, 7/16 DIN(f) Economy calibration kit, DC to 6 GHz, 7 mm Economy calibration kit, DC to 6 GHz, Type-N, 50-ohm Standard calibration kit, DC to 9 GHz, Type-N, 50-ohm Standard calibration kit, DC to 9 GHz, 3.5 mm Standard calibration kit, DC to 3 GHz, Type-N 75-ohm Economy calibration kit, DC to 3 GHz, Type-N 75-ohm 85038A Standard calibration kit, DC to 7.5 GHz, 7-16 85039B 85052D 85054B 85054D 85514A 85515A Economy calibration kit, DC to 3 GHz, Type-F, 75-ohm Economy calibration kit, DC to 26.5 GHz, 3.5 mm Standard calibration kit, DC to 18 GHz, Type-N, 50-ohm Economy calibration kit, DC to 18 GHz, Type-N, 50-ohm 4-in-1 calibration kit, DC to 9 GHz, Type-N, 50-ohm (m) 4-in-1 calibration kit, DC to 9 GHz, Type-N, 50-ohm (f) 25
Page 1 and 2: Agilent FieldFox RF Analyzer N9912A
Page 3 and 4: Table of Contents Definitions Speci
Page 5 and 6: Maximum Measurable Cable Loss Using
Page 7 and 8: Cable and Antenna Analyzer (continu
Page 9 and 10: Display data Trace math Scale Title
Page 11 and 12: Network Analyzer (continued) Figure
Page 13 and 14: Spectrum Analyzer (Option 230 and 2
Page 15 and 16: Spectrum Analyzer (continued) Descr
Page 21 and 22: Receiver IF Bandwidth AM FM Narrow
Page 23: General Information (continued) Des

Agilent FieldFox RF Analyzer N9912A - Tessco

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?