Vogele Basic Training Hydraulics & Electrics

More documents

Recommendations

Info

E.2.0 Units of measurement in electrics E.2.9.2 Calculating electrical power The following formulas can be used to calculate electrical power P. P = U I * P = R I² * P = U² R The power P increases proportionally to the square of the current I. The power P increases proportionally to the square of the voltage U.
E.3.0 Relationships between units of electricity E.3.1 Ohm’s Law If a voltage (U) is applied to a resistor (R) in a closed electrical circuit, a specific current (I) will flow through that resistor (R). The relationship of the values to one another can be determined by means of simple formulas. The following formulas can be calculated to this end : If a voltage (U) is applied to a resistor (R), a current (I) will flow through the resistor (R). I = U R If a current (I) flows through a resistor (R), a voltage (U) has been applied to it. R = U I If a current (I) should flow through a resistor (R), the voltage (U) must be calculated. U = R * I
Page 1 and 2:
Basic Training Hydraulics & Electri
Page 3 and 4:
Table of Contents - Hydraulics H.1.
Page 5 and 6:
Basic Principles Hydraulics
Page 7 and 8:
H.3.0 Units of measurement in hydra
Page 9 and 10:
H.5.0 Circuit symbols and circuits
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
H.6.0 Circuit diagrams H.6.1 Types
Page 25 and 26:
H.6.0 Circuit diagrams H.6.2 Layout
Page 27 and 28: H.6.0 Circuit diagrams H.6.2 Layout
Page 29 and 30: H.6.0 Circuit diagrams H.6.4 Symbol
Page 31 and 32: H.6.0 Circuit diagrams H.6.4 Symbol
Page 33 and 34: H.7.0 Open circuit The hydraulic pu
Page 35 and 36: H.7.0 Open circuit H.7.2 Directiona
Page 37 and 38: H.7.0 Open circuit H.7.4 Flow contr
Page 39 and 40: H.7.0 Open circuit H.7.6 Free-wheel
Page 41 and 42: H.8.0 Closed circuit The hydraulic
Page 43 and 44: H.8.0 Closed circuit H.8.2 Changing
Page 45 and 46: H.8.0 Closed circuit H.8.4 Leakage
Page 47 and 48: H.8.0 Closed circuit H.8.6 Accessor
Page 49 and 50: H.9.0 Hydraulic pumps Flow directio
Page 51 and 52: H.9.0 Hydraulic pumps H.9.3 Variabl
Page 53 and 54: H.9.0 Hydraulic pumps H.9.3 Variabl
Page 55 and 56: H.10.0 Hydraulic motors Hydraulic m
Page 57 and 58: H.10.3 Variable displacement motor
Page 59 and 60: H.12.0 Oils used at VÖGELE Motor o
Page 61 and 62: H.13.0 Annex H.13.2 Advantages The
Page 63 and 64: H.13.0 Annex H.13.5 Applications On
Page 65 and 66: H.13.0 Annex H.13.5.2 Combustion re
Page 67 and 68: Basic Principles Electrics
Page 69 and 70: E.2.0 Units of measurement in elect
Page 77: E.2.0 Units of measurement in elect
Page 81 and 82: E.4.0 Connecting resistors E.4.1.1
Page 83 and 84: E.4.0 Connecting resistors E.4.2.1
Page 85 and 86: E.5.0 Legend of abbreviations: A =
Page 87 and 88: E.6.0 Circuit symbols E.6.2 Symbols
Page 89 and 90: E.6.0 Circuit symbols E.6.4.Symbols
Page 91 and 92: E.7.0 Relays E.7.2 Relays used at V
Page 93 and 94: E.8.0 Diodes E.8.2 Conducting direc
Page 95 and 96: E.9.0 Fuses What is a fuse The weak
Page 97 and 98: E.10.0 Reading a circuit diagram E.
Page 99 and 100: E.11.0 Mains systems E.11.2 Mains 2
Page 101 and 102: E.12.0 Measuring instruments E.12.1
Page 103: E.12.0 Measuring instruments E.12.2
show all

Vogele Basic Training Hydraulics & Electrics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?