Operating Manual Hopper loader
Operating Manual Hopper loader Operating Manual Hopper loader
METRO 0.5 to 1.5 Transport and setup 4 Connections 4.2.2 Fastening material/vacuum hose MATERIAL DAMAGE! CAUTION! Incorrectly attached material tubes cause transport problems and damage to the hopper loader. Lay out material/vacuum hose to the hopper loader with a sufficiently wide curve. Ground the hose. Fig. 4.4 – Flow direction [1] Flow direction with PU tubes Note the flow direction (PU tubes only, optional), (see figure 4.4). Incorrect installation direction may influence the transport output. Fig. 4.5 – Grounding material/vacuum hose [1] Wire spiral Remove the wire spiral [1] from the tube and bend it inwards to make it contact the hopper loader. Slide the material/vacuum hose on to the connection on the hopper loader and fasten the hose with a suitable hose band clip (see Figure 4.5). Edition: November 2005 19
4 Transport and setup Connections METRO 0.5 to 1.5 4.2.3 Electrical connection Connecting the control cable CAUTION! MATERIAL DAMAGE! Radiant heat and hot surfaces may damage the controller cable. Lay out the controller cable so it will not be damaged by the heat of downstream units (hot surfaces or radiant heat)! Fig. 4.6 – Connecting control cable METRO *C/J* [1] Control cable connection Fig. 4.7 – Connecting control cable METRO *P* [1] Control cable connection The electrical power is supplied from the controller via the controller cable (see figure 4.64.7). 20 Edition: November 2005
- Page 1 and 2: Hopper loader METRO 0.5 to 1.5 Oper
- Page 3 and 4: METRO 0.5 to 1.5 Technical specific
- Page 5 and 6: METRO 0.5 to 1.5 Technical specific
- Page 7: 4 Transport and setup Connections M
- Page 11 and 12: 5 Structure and function Function M
- Page 13 and 14: METRO 0.5 to 1.5 Maintenance and re
- Page 15 and 16: METRO 0.5 to 1.5 Maintenance and re
- Page 17 and 18: METRO 0.5 to 1.5 Maintenance and re
- Page 19 and 20: 11 Option Implosion filter option M
- Page 21 and 22: METRO 0.5 to 1.5 Appendix 12 METRO
- Page 23 and 24: METRO 0.5 to 1.5 Appendix 12 METRO
- Page 25 and 26: METRO 0.5 to 1.5 Appendix 12 Multif
- Page 27 and 28: 12 Appendix Multifunction panel MET
- Page 29 and 30: A B C D E 2 A1 +ZSW PE + 24V M VACV
- Page 31: A B C D E 2 3 4 5 6 7 8 A1 +ZSW PE
METRO 0.5 to 1.5<br />
Transport and setup 4<br />
Connections<br />
4.2.2 Fastening material/vacuum hose<br />
MATERIAL DAMAGE!<br />
CAUTION!<br />
Incorrectly attached material tubes cause transport problems and damage to the hopper<br />
<strong>loader</strong>.<br />
Lay out material/vacuum hose to the hopper <strong>loader</strong> with a sufficiently wide curve.<br />
Ground the hose.<br />
Fig. 4.4 – Flow direction<br />
[1] Flow direction with PU tubes<br />
Note the flow direction (PU tubes only, optional), (see figure 4.4). Incorrect installation direction<br />
may influence the transport output.<br />
Fig. 4.5 – Grounding material/vacuum hose<br />
[1] Wire spiral<br />
Remove the wire spiral [1] from the tube and bend it inwards to make it contact the hopper <strong>loader</strong>.<br />
Slide the material/vacuum hose on to the connection on the hopper <strong>loader</strong> and fasten the hose<br />
with a suitable hose band clip (see Figure 4.5).<br />
Edition: November 2005 19