Igepa group GmbH & Co. KG, Sachsenfeld 4 D-20097 Hamburg

DIN Safety Data Sheet
1. Product PMMA XT
1.1 Chemical Characterization Acrylic Polymer based on Methylmethacrylate
1.2 Form Sheets
1.3 Colour Colourless (transparent)
1.4 Odour Odourless
2. Physical data and safety data
2.1 Change in Physical State Softening temperature about 102°C
2.2 Density (20°C) 1.19 g/cm³
2.3 Vapour Pressure Not applicable
2.4 Vicosity Not applicable
2.5 Solubility in Water Insoluble
2.6 pH value not applicable
2.7 Flash point 390°C (ASTM-D 1929-68)
2.8 Ignition Temperature 465°C (ASTM-D 1929-68)
2.9 Explosion Limits Not applicable
2.10 Thermal Decomposition About 280°C
2.11 Hazardous Decomposition With proper handling – none.
On thermal decomposition vapours, consisting
predominantly of Methylmethacrylate, are formed,
which are inflammable and irritating to the eyes and
respiratory system.
Igepa group GmbH & Co. KG, Sachsenfeld 4 D-20097 Hamburg, phone +49-40-72 77 88-0, fax +49-40-72 77 88-50, info@igepagroup.com, www.igepagroup.com

DIN Safety Data Sheet
2.12 Hazardous reaction With proper handling – none
2.13 Further information None
-------------------------------------------------------------------------------------------------------
3. Transport
GGV See/IMDG’ Code not applicable
UN No “ “
ICAD/IATA-DGr “ “
GGVE/GGVS “ “
RID/ADR “ “
ADNR “ “
-------------------------------------------------------------------------------------------------------
4. Regulations
PMMA XT colourless does not require labeling
as specified in EEC Directive 79/831/EEC and
amendments.
5. Protective Measures, Storage and Handling
5.1 Technical Protective Measures With normal handling no special measures are
necessary.
Protective measures should be taken when machining
including using a suction device for dust and chips.
5.2 Personal Protective Equipment
Respiratory protection
Eye protection
Hand protection
Other
None on normal handling
On machining it may be necessary to use a dust mask.
Safety glasses during machining
Not required
None
5.3 Industrial Hygiene Observe usual standards of industrial hygiene
5.4 Protection against Fire
& Explosion
No special measures necessary.
5.5 Disposal Product may be disposed of together with household
refuse or industrial refuse taking care to follow local
authorities regulations.
Igepa group GmbH & Co. KG, Sachsenfeld 4 D-20097 Hamburg, phone +49-40-72 77 88-0, fax +49-40-72 77 88-50, info@igepagroup.com, www.igepagroup.com

DIN Safety Data Sheet
-------------------------------------------------------------------------------------------------------
6. Measures to be taken in case of Accidents and Fires.
6.1 Spillage/Leakage Vacuum and dispose of as written above
6.2 Suitable Extinguishing Equipment Water-spray, foams, carbon dioxide, dry chemical
Not to be Used Direct Water Jet
6.3
First Aid
Upon irritation of the eyes – wash eyes with plenty of
tap water for about 15 minutes.
If
irritation persists consult a doctor.
6.4 Further Information None
7. Toxicity
-------------------------------------------------------------------------------------------------------
PMMA XT is not to be regarded as a hazardous
material.
With proper handling and provided the standards of
industrial hygiene and safety in the work place are
followed, no health hazards should be expected.
8. Ecological Effects
PMMA XT is a solid material, insoluble in water and
non-toxic, therefore no adverse effects on the
environment should be expected.
This information reflects our current knowledge. It serves to describe the product and cannot
be interpreted as a guarantee of certain properties.
Igepa group GmbH & Co. KG, Sachsenfeld 4 D-20097 Hamburg, phone +49-40-72 77 88-0, fax +49-40-72 77 88-50, info@igepagroup.com, www.igepagroup.com