accessories – price list

CONTENTS
ROCKWOOL
Wired Back Mattress……………………………………………………………………………….. Page 3
Technical Specifications…………………………………………………………………………... Page 4
Wired Back Mattress Price List………………………………………………………………… Page 5
Pipe Sections……………………………………………………………………………………………. Page 6
Technical Specifications…………………………………………………………………………… Page 7
Pipe Section Price List……………………………………………………………………………… Page 8
POLYURETHANE RIGID FOAM
Data Sheets and Technical Specifications………………………………………………… Page 18
Foam Sheet Price List………………………………………………………………………………. Page 24
Foam Pipe Section Price List……………………………………………………………………. Page 25
CEMENT
TPH300 cement……………………………………………………………………………………….. Page 27
ENVIRO CLEAN HAND CLEANER
Data and Price…........................................................................................... Page 28
ACCESSORIES AND TOOLS
Pictures………………………………………………………………………………………………….. Page 29
Prices……………………………………………………………………………………………………… Page 37

WIRED MATTRESS
WIRED MATTRESSES
Rockwool 159 is a lightly bonded heavy stone wool
mat ,stitched on galvanised wired mesh with
galvanised wire.
The wired mat is especially suitable for industrial
installations such as high-pressure steam pipes,
reactors, furnaces, etc. where high demands are
made on the temperature resistance of the
insulation.
Rockwool Wired Back Mattresses come in various
densities, lengths and thicknesses
Rockwool 159 (Wired mat)
Installation guidelines
Assembly
Cut the wired mat to length, so that the mat fits the pipe with slight pre-stressing. The closing joints must
be staggered at an angle of at least 30 degrees to each other. The closing joints of the mats (lengthwise
and circular joints) must be wired together using e.g. steel wire min. 0,5 mm or secured with mat hooks.
Stainless steel pipes and pipes with a temperature of > 350°C should preferably be insulated with
Rockwool 159 SW, in which both the mesh and the stitching wire is in stainless steel. If the mats are
assembled in multiple layers, both the lengthwise and circular joints must be staggered (‘masonry bond’).
Support construction
Given the limited pressure resistance of wired mats, in most cases a support is required for the board
cladding. As a guideline, assume that a support is required every 3 to 4 metres.
Finishing
The insulation should be finished with a metal (e.g. aluminium) cladding. Where necessary, expansion
joints are provided to cater for expansion of the pipes. Both the lengthwise and circular joints are
fastened with sheet-metal screws: hard aluminium or stainless steel 1/2”, 8/metre. Close the expansion
joints with a steel tensioning wire. Connections to mountings, head and end caps, etc. should be made
watertight using a suitable sealant.
Click to go back to contents

WIRED MATTRESSES – THERMAL CONDUCTIVITY
Performance Temperature Value Unit of measure Standard Standard
t°m (°C) 50 0.04 λ (W/mK) EN 12667 ASTM C177
t°m (°C) 100 0.046 λ (W/mK) EN 12667 ASTM C177
t°m (°C) 150 0.052 λ (W/mK) EN 12667 ASTM C177
t°m (°C) 200 0.06 λ (W/mK) EN 12667 ASTM C177
t°m (°C) 250 0.069 λ (W/mK) EN 12667 ASTM C177
t°m (°C) 300 0.081 λ (W/mK) EN 12667 ASTM C177
t°m (°F) 100 0.273 λ (BTU.in/ft².h.°F) EN 12667 ASTM C177
t°m (°F) 200 0.301 λ (BTU.in/ft².h.°F) EN 12667 ASTM C177
t°m (°F) 300 0.349 λ (BTU.in/ft2.h.°F) EN 12667 ASTM C177
t°m (°F) 400 0.413 λ (BTU.in/ft².h.°F) EN 12667 ASTM C177
t°m (°F) 500 0.497 λ (BTU.in/ft².h.°F) EN 12667 ASTM C177
t°m (°C) 600 0.6 λ (BTU.in/ft².h.°F) EN 12667 ASTM C177
PROPERTY PERFORMANCE STANDARD
Maximum Service
Temperature
WIRED MATTRESSES – TECHNICAL PROPERTIES AND STANDARDS
660°C (1220 F°) EN 14706
750°C (1382 F°) ASTM C411
Reaction to fire A1 EN 13501-1
Surface burning characteristics: Flame spread=passed, Smoke development=passed ASTM E84 (UL 723)
Water leachable
chloride content
< 10mg/kg, AS-quality for use over stainless steel EN 13468
Conforms to the stainless steel corrosion specification as per ASTM test methods C692
and C871
ASTM C795
< 10mg/kg (ph-value neutral to slightly alkaline) ASTM C871
Water absorption Water absorption < 1 kg/m² EN 1609
Water vapour absorption (vapour sorption) ± 0.02%vol
ASTM C1104/C1104M
Nominal density
Water vapour
resistance factor
Compliance
100 kg/m³ (6.2 lb/ft)
μ = 1.0 EN 12086
Rockwool (RW) wire mesh blankets for thermal insulation of large diameter pipes, flat
walls and equipment
CINI 2.2.02
Standard specification for mineral fibre blanket insulation, type I and II (NaN F°) ASTM C592-06
Click to go back to contents

WIRED MATTRESSES PRICE LIST
DENSITY LENGTH WIDTH THICKNESS METRES
m2
R/m2 R/ROLL TRANSPORT TOTAL
80 5000 1000 50mm 5000 R101.49 R507.45 R23.62 R531.07
100 6000 1000 40mm 6000 R102.09 R612.52 R24.62 R637.14
100 5000 1000 50mm 5000 R127.62 R638.08 R30.78 R668.86
100 3000 1000 75mm 3000 R185.30 R555.91 R30.78 R586.69
100 2500 1000 100mm 2500 R241.98 R604.95 R38.61 R643.56
Click to go back to contents

PIPE SECTIONS
Rockwool Pipe Sections are a pre-fabricated stone
wool pipe section. The sections are supplied split
and hinged for easy snap-on assembly, and are
suitable for the thermal and acoustic insulation
of industrial pipe work
Pipe Sections are supplied in 1.2 m Lengths
Advantages
• Excellent thermal and acoustic insulation
• Easy to handle and install
• Wide range of diameters and insulation thicknesses
• Optimal performance due to the extensive range of diameters
• Suitable for use over stainless steel
• For temperatures up to 350°C, a support construction is not generally necessary
• Long lasting
• Excellent fit provides optimal performance
• Fast return on investment
Installation guidelines
Assembly
Fit the Rockwool 850 closely around the pipe, with the lengthwise (horizontal) joint turned towards the
underside. The lengthwise joints must be staggered at an angle of at least 30 degrees to each other. The
shell is secured with galvanised binding wire (thickness 0.5 mm, at least 3/m). For insulation thickness
above 100 mm (or temperatures > 250°C) the insulation should be applied in at least two layers. In the
case of multi-layer insulation it is recommended that the lengthwise and crosswise joints are staggered
(‘masonry bond’).
Support construction
On pipes where mechanical loading (e.g. strong vibrations) of the insulation is expected and/or the
temperature is higher than 350°C, a support structure (spacers) should be constructed. The number of
spacers depends on the temperature and the mechanical load. As a guide, the following intermediate
distances can be used:
Horizontal pipe work: 3 to 4 m
Vertical pipe work: 5 to 6 m
Finishing
All pipe sections should be finished with a metal (e.g. aluminium) cladding. Where necessary, expansion
joints are required to cater for expansion of the pipes. Both the lengthwise and circular joints are
fastened with sheet-metal screws: hard aluminium or stainless steel 1/2”, 8 per metre. Close expansion
joints with a steel tensioning wire. Connections to mountings, head and end caps, etc. should be made
watertight using an appropriate sealant.
Click to go back to contents

PIPE SECTION – THERMAL CONDUCTIVITY
Performance Temperature Value Unit of measure Standard Standard
t°m (°C) 50 0.038 λ (W/mK) EN ISO 8497 ASTM C335
t°m (°C) 100 0.044 λ (W/mK) EN ISO 8497 ASTM C335
t°m (°C) 150 0.051 λ (W/mK) EN ISO 8497 ASTM C335
t°m (°C) 200 0.061 λ (W/mK) EN ISO 8497 ASTM C335
t°m (°C) 250 0.073 λ (W/mK) EN ISO 8497 ASTM C335
t°m (°C) 300 0.087 λ (W/mK) EN ISO 8497 ASTM C335
t°m (°F) 100 0.257 λ (BTU.in/ft².h.°F) EN ISO 8497 ASTM C335
t°m (°F) 200 0.296 λ (BTU.in/ft².h.°F) EN ISO 8497 ASTM C335
t°m (°F) 300 0.354 λ (BTU.in/ft².h.°F) EN ISO 8497 ASTM C335
t°m (°F) 400 0.429 λ (BTU.in/ft².h.°F) EN ISO 8497 ASTM C335
t°m (°F) 500 0.524 λ (BTU.in/ft².h.°F) EN ISO 8497 ASTM C335
t°m (°F) 600 0.637 λ (BTU.in/ft².h.°F) EN ISO 8497 ASTM C335
PIPE SECTION – TECHNICAL PROPERTIES AND STANDARDS
Property Performance Standard
Maximum Service
Temperature
620°C (1148 F°) EN 14707
750°C (1382 F°) ASTM C411
Reaction to fire A1 EN 13501-1
Non-combustible IMO A.799 (19)
Low Surface Flame Spread IMO A.653 (16)
Surface burning characteristics: Flame spread=passed, Smoke development=passed ASTM E84 (UL 723)
Water leachable
chloride content
< 10 mg/kg, AS-quality for use on stainless steel EN 13468
Conforms to the stainless steel corrosion specification as per ASTM test methods
ASTM C795
< 10mg/kg (pH-value neutral to slightly alkaline) C692 and C871 ASTM C871
Water absorption Water absorption < 1 kg/m² EN 13472
Water vapour absorption (vapour sorption) ± 0.02%vol
ASTM C1104/C1104M
Nominal density
Water vapour
resistance factor
100kg/m³ to 125kg/m³ (6.2 lb/ft - 7.8 lb/ft)
μ = 1,0 EN 13469
Compliance Rockwool sections. For the thermal insulation of pipes. CINI 2.2.03
Standard specification for mineral fibre pre-formed pipe insulation, type I, II and IV ASTM C547-06
Click to go back to contents

PIPE SECTION – PRICE LIST
ROCKWOOL PER METRE PER 1.2 M SECTION
NB OD MM Wall TH LIST PRICE LIST PRICE
15 21.6 20 R 16.09 R 19.31
15 21.6 25 R 22.53 R 27.04
15 21.6 30 R 29.94 R 35.93
15 21.6 40 R 47.65 R 57.18
15 21.6 50 R 69.24 R 83.08
20 26.9 20 R 18.14 R 21.77
20 26.9 25 R 25.09 R 30.11
20 26.9 30 R 33.01 R 39.62
20 26.9 40 R 51.75 R 62.10
20 26.9 50 R 74.36 R 89.23
25 34.3 20 R 21.00 R 25.20
25 34.3 25 R 28.67 R 34.41
25 34.3 30 R 37.31 R 44.77
25 34.3 40 R 57.48 R 68.97
25 34.3 50 R 81.52 R 97.82
32 43.2 20 R 24.45 R 29.33
32 43.2 25 R 32.97 R 39.57
32 43.2 30 R 42.47 R 50.96
32 43.2 40 R 64.36 R 77.24
32 43.2 50 R 90.12 R 108.15
40 48.2 20 R 26.38 R 31.66
40 48.2 25 R 35.39 R 42.47
40 48.2 30 R 45.37 R 54.45
40 48.2 40 R 68.23 R 81.88
40 48.2 50 R 94.96 R 113.95
Click to go back to contents

PIPE SECTION – PRICE LIST
ROCKWOOL PER METRE PER 1.2 M SECTION
NB OD MM Wall TH LIST PRICE LIST PRICE
50 60.3 20 R 31.06 R 37.27
50 60.3 25 R 41.24 R 49.49
50 60.3 30 R 52.39 R 62.87
50 60.3 40 R 77.59 R 93.11
50 60.3 50 R 106.66 R 127.99
65 76.2 20 R 37.21 R 44.65
65 76.2 25 R 48.93 R 58.72
65 76.2 30 R 61.62 R 73.94
65 76.2 40 R 89.89 R 107.87
65 76.2 50 R 122.03 R 146.44
80 88.9 20 R 42.12 R 50.55
80 88.9 25 R 55.07 R 66.08
80 88.9 30 R 68.98 R 82.78
80 88.9 40 R 99.72 R 119.66
80 88.9 50 R 134.31 R 161.18
90 101.6 20 R 47.03 R 56.44
90 101.6 25 R 61.21 R 73.45
90 101.6 30 R 76.35 R 91.62
90 101.6 40 R 109.54 R 131.45
90 101.6 50 R 146.60 R 175.91
100 114.3 20 R 52.10 R 62.52
100 114.3 25 R 67.54 R 81.05
100 114.3 30 R 83.95 R 100.74
100 114.3 40 R 119.67 R 143.61
100 114.3 50 R 159.26 R 191.12
Click to go back to contents

PIPE SECTION – PRICE LIST
ROCKWOOL` PER METRE PER 1.2 M SECTION
NB OD MM Wall TH LIST PRICE LIST PRICE
15 21.6 60 R 90.90 R 109.08
15 21.6 70 R 119.05 R 142.86
15 21.6 80 R 150.91 R 181.09
20 26.9 60 R 96.81 R 116.17
20 26.9 70 R 125.94 R 151.12
20 26.9 80 R 158.78 R 190.54
25 34.3 60 R 105.05 R 126.06
25 34.3 70 R 135.55 R 162.66
25 34.3 80 R 169.77 R 203.73
32 43.2 60 R 114.96 R 137.96
32 43.2 70 R 147.12 R 176.54
40 48.2 60 R 120.53 R 144.64
40 48.2 70 R 153.62 R 184.34
Click to go back to contents

PIPE SECTION – PRICE LIST
ROCKWOOL PER METRE PER 1.2 M SECTION
NB OD MM Wall TH LIST PRICE LIST PRICE
50 60.3 60 R 134.01 R 160.82
50 60.3 70 R 169.34 R 203.21
50 60.3 80 R 208.39 R 250.07
50 60.3 90 R 251.15 R 301.38
50 60.3 100 R 297.62 R 357.14
65 76.2 60 R 151.73 R 182.07
65 76.2 70 R 190.01 R 228.01
65 76.2 80 R 232.01 R 278.41
65 76.2 90 R 277.72 R 333.26
65 76.2 100 R 327.14 R 392.57
80 88.9 60 R 165.87 R 199.05
80 88.9 70 R 206.51 R 247.82
80 88.9 80 R 250.87 R 301.04
80 88.9 90 R 298.94 R 358.73
80 88.9 100 R 350.72 R 420.86
90 101.6 60 R 180.02 R 216.02
90 101.6 70 R 223.02 R 267.62
90 101.6 80 R 269.73 R 323.68
90 101.6 90 R 320.16 R 384.19
90 101.6 100 R 374.30 R 449.16
100 114.3 60 R 194.61 R 233.54
100 114.3 70 R 240.05 R 288.05
100 114.3 80 R 289.19 R 347.03
100 114.3 90 R 342.05 R 410.46
100 114.3 100 R 398.62 R 478.35
Click to go back to contents

PIPE SECTION – PRICE LIST
ROCKWOOL PER METRE PER 1.2 M SECTION
NB OD MM Wall TH LIST PRICE LIST PRICE
115 127.0 20 R 54.59 R 65.50
115 127.0 25 R 70.55 R 84.66
115 127.0 30 R 87.45 R 104.94
115 127.0 40 R 124.02 R 148.83
115 127.0 50 R 164.31 R 197.18
125 139.5 20 R 59.23 R 71.07
125 139.5 25 R 76.35 R 91.63
125 139.5 30 R 94.41 R 113.29
125 139.5 40 R 133.31 R 159.97
125 139.5 50 R 175.92 R 211.10
150 168.4 20 R 69.96 R 83.95
150 168.4 25 R 89.77 R 107.72
150 168.4 30 R 110.51 R 132.61
150 168.4 40 R 154.77 R 185.72
150 168.4 50 R 202.75 R 243.29
175 193.5 20 R 79.28 R 95.13
175 193.5 25 R 101.42 R 121.70
175 193.5 30 R 124.49 R 149.39
175 193.5 40 R 173.41 R 208.09
175 193.5 50 R 226.05 R 271.26
Click to go back to contents

PIPE SECTION – PRICE LIST
ROCKWOOL PER METRE PER 1.2 M SECTION
NB OD MM Wall TH LIST PRICE LIST PRICE
200 219.0 20 R 88.75 R 106.50
200 219.0 25 R 113.26 R 135.91
200 219.0 30 R 138.69 R 166.43
200 219.0 40 R 192.35 R 230.82
200 219.0 50 R 249.72 R 299.66
225 244.5 20 R 84.94 R 101.93
225 244.5 25 R 108.19 R 129.82
225 244.5 30 R 132.23 R 158.68
225 244.5 40 R 182.73 R 219.28
225 244.5 50 R 236.45 R 283.74
250 273.0 20 R 94.10 R 112.92
250 273.0 25 R 119.63 R 143.55
250 273.0 30 R 145.96 R 175.15
250 273.0 40 R 201.04 R 241.25
250 273.0 50 R 259.33 R 311.19
275 298.0 20 R 102.13 R 122.55
275 298.0 25 R 129.66 R 155.60
275 298.0 30 R 158.01 R 189.61
275 298.0 40 R 217.10 R 260.52
275 298.0 50 R 279.40 R 335.28
300 324.0 20 R 110.48 R 132.57
300 324.0 25 R 140.10 R 168.12
300 324.0 30 R 170.53 R 204.64
300 324.0 40 R 233.80 R 280.56
300 324.0 50 R 300.27 R 360.33
Click to go back to contents

PIPE SECTION – PRICE LIST
ROCKWOOL PER METRE PER 1.2 M SECTION
NB OD MM Wall TH LIST PRICE LIST PRICE
350 358.0 60 R 465.65 R 558.78
350 358.0 70 R 556.25 R 667.50
350 358.0 80 R 650.57 R 780.68
350 358.0 90 R 748.60 R 898.32
350 358.0 100 R 850.34 R 1,020.41
375 381.0 60 R 491.27 R 589.52
375 381.0 70 R 586.14 R 703.37
375 381.0 80 R 684.73 R 821.68
375 381.0 90 R 787.03 R 944.44
375 381.0 100 R 893.05 R 1,071.66
400 408.0 60 R 521.35 R 625.62
400 408.0 70 R 621.23 R 745.48
400 408.0 80 R 724.83 R 869.80
400 408.0 90 R 832.15 R 998.58
400 408.0 100 R 943.18 R 1,131.81
425 432.0 60 R 548.08 R 657.70
425 432.0 70 R 652.43 R 782.91
425 432.0 80 R 760.48 R 912.58
425 432.0 90 R 872.25 R 1,046.70
425 432.0 100 R 987.74 R 1,185.28
Click to go back to contents

PIPE SECTION – PRICE LIST
ROCKWOOL PER METRE PER 1.2 M SECTION
NB OD MM Wall TH LIST PRICE LIST PRICE
450 457.0 60 R 575.93 R 691.12
450 457.0 70 R 684.92 R 821.90
450 457.0 80 R 797.61 R 957.14
450 457.0 90 R 914.03 R 1,096.83
450 457.0 100 R 1,034.15 R 1,240.98
500 508.0 60 R 547.24 R 656.69
500 508.0 70 R 649.69 R 779.62
500 508.0 80 R 755.34 R 906.41
500 508.0 90 R 864.21 R 1,037.06
500 508.0 100 R 976.29 R 1,171.55
550 558.0 60 R 595.41 R 714.49
550 558.0 70 R 705.89 R 847.06
550 558.0 80 R 819.57 R 983.49
550 558.0 90 R 936.47 R 1,123.77
550 558.0 100 R 1,056.58 R 1,267.90
600 609.0 60 R 644.55 R 773.46
600 609.0 70 R 763.21 R 915.85
600 609.0 80 R 885.09 R 1,062.11
600 609.0 90 R 1,010.18 R 1,212.21
600 609.0 100 R 1,138.47 R 1,366.17
700 711.0 60 R 742.82 R 891.38
700 711.0 70 R 877.86 R 1,053.43
700 711.0 80 R 1,016.12 R 1,219.34
Click to go back to contents

PIPE SECTION – PRICE LIST
ROCKWOOL PER METRE PER 1.2 M SECTION
NB OD MM Wall TH LIST PRICE LIST PRICE
200 219.0 60 R 310.80 R 372.96
200 219.0 70 R 375.60 R 450.72
200 219.0 80 R 444.11 R 532.93
200 219.0 90 R 516.33 R 619.60
200 219.0 100 R 592.27 R 710.72
225 244.5 60 R 293.37 R 352.04
225 244.5 70 R 353.51 R 424.21
225 244.5 80 R 416.85 R 500.22
225 244.5 90 R 483.41 R 580.09
225 244.5 100 R 553.18 R 663.82
250 273.0 60 R 320.83 R 384.99
250 273.0 70 R 385.54 R 462.65
250 273.0 80 R 453.46 R 544.16
250 273.0 90 R 524.60 R 629.52
250 273.0 100 R 598.94 R 718.73
275 298.0 60 R 344.91 R 413.90
275 298.0 70 R 413.64 R 496.37
275 298.0 80 R 485.58 R 582.69
275 298.0 90 R 560.73 R 672.87
275 298.0 100 R 639.09 R 766.90
300 324.0 60 R 369.96 R 443.96
300 324.0 70 R 442.87 R 531.44
300 324.0 80 R 518.98 R 622.77
300 324.0 90 R 598.30 R 717.96
300 324.0 100 R 680.84 R 817.00
Click to go back to contents

PIPE SECTION – PRICE LIST
ROCKWOOL PER METRE PER 1.2 M SECTION
NB OD MM Wall TH LIST PRICE LIST PRICE
115 127.0 60 R 208.32 R 249.98
115 127.0 70 R 256.03 R 307.24
115 127.0 80 R 307.46 R 368.95
115 127.0 90 R 362.60 R 435.12
115 127.0 100 R 421.46 R 505.75
125 139.5 60 R 222.24 R 266.69
125 139.5 70 R 272.28 R 326.73
125 139.5 80 R 326.03 R 391.23
125 139.5 90 R 383.49 R 460.19
125 139.5 100 R 444.67 R 533.60
150 168.4 60 R 254.43 R 305.32
150 168.4 70 R 309.84 R 371.80
150 168.4 80 R 368.95 R 442.74
150 168.4 90 R 431.78 R 518.14
150 168.4 100 R 498.32 R 597.99
175 193.5 60 R 282.40 R 338.87
175 193.5 70 R 342.46 R 410.95
175 193.5 80 R 406.23 R 487.48
175 193.5 90 R 473.72 R 568.47
175 193.5 100 R 544.93 R 653.91
Click to go back to contents

POLYURETHANE FOAM
RIGID POLYURETHANE FOAM
We manufacture rigid polyurethane foam slabs.
Polyurethane is an isolative material with excellent
thermal
properties. Polyurethane is mostly used in cold
applications from –15 C to 110 C.
Polyurethane is supplied in sheets of 2.440 x 1.220 x
thickness on request.
PIC FIRE RETARDANT FOAM
Polyisocyanurate foam has superior fire properties to
polyurethane foam. This is most obvious in resistance to
ignition and in smoke obscuration during standard tests
Click to go back to contents

POLYURETHANE FOAM – PU35
DATA SHEET
Polyurethane PU 35 Data Sheet
PHYSICAL PROPERTIES OF POLYURETHANE/POLYISOCYANURATE RIGID FOAMS
Both polyurethane and polyisocyanurate rigid foams are characterised by a very small
closed cell structure. Microscopic examination shows cells have thin poly-Metric
membranes as faces and solid struts at there edges. The gases in the cells endow the foarns
with very low thermal conductivities, the strength of the foams is due to the network of the
struts.
Because the overall volumetric proportion of plastic in insulation foams is about three to
four percent, their most obvious characteristic is very low density. This is typically 30 to 50
kg/m3 (2 to 3lb/ft3) and results in extreme ease of handling and installation - a very
significant advantage.
Typical physical properties of polyurethane and polyisocyanurate foams at nominal
densities of 32 and 50kg/m3 (2 and 3lb/ft3) are given in Table 1.
The information show is for slabstock foams as the physical form of the product facilitates
preparation of test samples that give representative data. The properties of foam
produced in other forms, such as spray foam or in-situ pipe insulation, may differ in detail
but will be generally similar.
Structural properties
Data show polyurethane and polyisocyanurate foams are sufficiently strong to be suitable
for applications where they are required to contribute to the overall struck tural properties
of the insulated component. Structural properties will increase with density, for
applications which require additional load-bearing properties, such as pipe supports,
densities of 80 to 100kg/m3 (5 to 6lb/ft3) may be used.
Click to go back to contents

POLYURETHANE FOAM – PU35
Moisture vapour transmission and water uptake.
As polyurethane and polyisocyanurate foams are almost entirely closed celled, water uptake
and the transmission of water vapour are very low. However, in common with other
insulating materials, both organic and inorganic, it is recommended that a moistureimpermeable
barrier is installed over the foam to ensure that the insulation remains
unimpaired over a long life.
Thermal insulation
The thermal conductivity of polyurethane and polyisocyanurate foams when first made is of
the order of 0.017 W/mK (c 12 Btu in/ft h F). If the foam is covered by a gas-tight barrier, this
extremely low value can be retained. Long-term retention of low conductivity values has been
observed in many examples in different fields of application. Where a gas-tight barrier is not
used the thermal conductivity will increase typically to 0.023 W/mk (0.16 Btu in/ft h F), by
the well-understood mechanism of air diffusion through the cell membranes into the cells.
Extensive laboratory measurements carried out over many years, have aided the study
and understanding of the thermal conductivity of polyurethane and polyisocyanurate
foams in plant applications. In addition there have been many cases where foam has
been examined after several years in service.
1. A sample of polyisocyanurate foam, taken from the insulation of an ammonia
tank, was found to have a thermal conductivity of 0.025 W/mK (0,18 Btu in/ft2hF)
at 10 C (50 F). The insulation had been in place for 10 years on this tank, normally
operating at -40 C (-40 F), at an ICI chemical complex in NE England.
2. 2. Several pofyisocyanurate samples were taken from the insulation of vessels and
tanks at a major petrochemical complex after many years in service. The thermal
conductivities measured were in the range of 0.023 to 0.025 W/mk (0.016 to 0.018
Btu in/ft2h F) at 10C(50F),
There are several examples not associated with plant applicatons. In which low thermal
conductivities have been recorded after many years of service.
Click to go back to contents

POLYURETHANE FOAM – PU35
1. Metal faced polyurethane panels which had been used to insulate a cold store in
England for more than 10 years had a thermal conductivity of 0.022 W/mK (0.15
Btu in/ft2h F)at 10C(50F).
2. Samples have been taken from domestic chest freezers removed from service
because of compressor failure. These polyurethane foams were found to have,
thermal conductivities in the range 0.017 to 0.018 W/mK (0.12 to 0.13 Btu in/ft2h F)
at 10 C (50 F).
The understanding gained from long-term laboratory measurements, coupled with
these - and many other - examples of polyurethane and polyisocyanurate foams that
have given many years of reliable service provide a large data bank of knowledge and
experience.
Note : The very low value of thermal conductivity is partly due to the use of CFC 11 as the
blowing agent and its entrapment within the cell structure. Legislation Such as the
Montreal Protocol is now limiting the availability of CFC 11. Developments in foam
technology, based on alternative blowing agents, are reducing and will eliminate the use of
CFC 11. The new foams will retain all the desirable characteristics of established foams.
Stability and service temperatures
Data show pofyurethane and polyisocyanurate foams have very good dimensional stability
over a wide range of temperatures and conditions. They have been used for many years
for the insulation of tanks at cryogenic temperatures. The upper temperature limit for
continuous use of polyurethane foam is 100 C (212 F), the more thermally stable
polyisocyanurate foam can be used continuously at temperature up to 140 C (284 F).
Corrosion resistance
The closed-cell nature of polyurethane and polyisocyanurate foams will prevent the
corrosion of mild steel substrates by protecting them from the ingress of water and
oxygen. For effective protection, the surface must be in good condition before the foam is
applied and it is normal practise to coat the substrate with an appropriate primer before
the foam insulation is installed. It is also recommended that a primer be applied to stainless
steel substructures if the working temperature is likely to exceed 60 C (140 F).
Click to go back to contents

POLYURETHANE FOAM – PU35
Table 1
Typical physical properties of polyurethane and polyisocyanurate slabstock
foams.
Property Units PIR/PIC PIR/PIC
Nominal density kg/m3 (Ib/ft3) 35(2) 50(3.1)
Compressive strength
kPa (Ib/in2)
Parallel to rise 220 (32) 380 (55)
Perpendicular to rise 140 (20) 300 (44)
Tensile strength
kPa (Ib/in2)
Perpendicular to rise 240 (35) 500 (73)
Shear strength kPa (Ib/in2) 160(23) 300 (44)
Closed cell content % 98 95
Moisture
vapour
transmission
ugm/Nn
(perm in) 12(2.4) 8(1.6)
Water absorption % W/V 4 2
Thermal conductivity W/mk(Btu in/ft2 h F)
Unaged 0.017(0.1
0.017(0.12)
2)
Aged
0.023to0.
0.023to0.024
025
Dimensional stability %linear change (0.16to0.1
(0.16to0.17)
8)
-20 C for 24 hours negligible negligible
+1 10 C for 24 hours 1.0 1.0
+70C,100%RHfor
2.0 2.0
24 hours
Upper
temperature
limit C(F) 100(212) 100(212)
Linear coefficient
of expansion 10 1C 40 to 80 40 to 80
(10 / F) (22 to 44) (22 to 44)
Click to go back to contents

POLYURETHANE FOAM – PU35
Fire performance of polyurethane/polyisocyanurate rigid foams
Polyurethane and polyisocyanurate foams are organic materials and hence combustible. Precautions must be
taken to ensure that they are correctly formulated, installed and that the appropriate protection is
provided.
Polyurethane and polyisocyanurate foams should never be used without a protective outer layer. In addition, care
must be taken during installation and maintenance, when the foam may be exposed, to protect it from potential
sources of ignition.
However, over 700000 tones of polyurethane and polyisocyanurate foams are used in the building industry
generally, where fire regulations have invariably to be met. This is possible because the foams themselves and
composites containing them can meet a wide range of stringent national and international fire regulations.
Polyisocyanurate foam has superior fire properties to polyurethane foam. This is most obvious in resistance to
ignition and in smoke obscuration during standard tests.
One of the reasons why polyisocyanurate gives benefits in this area I that at the high temperatures encountered in a
fire, the surface may degrade to form a carbonaceous char which protects the foam behind it and restricts further
involvement in the fire. In many plant applicatons this is a very desirable characteristic.
Typical fire test properties
Typical properties of foams in a selection of fire tests are listed in Table 2. There are many national, and an
increasing number of international, fire tests in existence, the table gives only an indication of the fire performance
in the better known tests.
Fire test data from national tests will often be necessary to satisfy local regulations. No attempt should be made to
extrapolate from or to compare the results of different tests fire performance is not sufficiently well understood for
data manipulation to be justified.
Large-scale tests
As in other fields of fire testing, investigation of the performance of plant insulation sometimes involves large scale
ad hoc tests. One such test programme has demonstrated that 50mm (2 in) of polyisocyanurate foam - which is
combustible -offers comparable performance to 90mm (3 5 in) of cellular glass - which is not - in a composite fire
protection system applied to 200-mm (6-in) diameter pipes.
The external surfaces were exposed to temperatures up to 1,000 C (1,830 F) and internal temperature changes
recorded. Up to 800 C (1,470 F), polyisocyanurate foam formed a carbonaceous char about 40-mm (1-5 in) thick,
no cracks penetrated the full depth of the foam. In the cellular glass, many interconnected cracks, some more
than 25mm (1-in) wide, penetrated its full depth. At 1,000 C (1,830 F), neither insulation was very effective.
Click to go back to contents

POLYURETHANE FOAM – PU35
PU35 SHEET PRICE LIST
MM
1220 x 2440 1220 x 2440 1000 x 2440
35 kg/m3 40kg/m3
80kg/m
3
13 R 98.48 R 123.10 R 177.26
15 R 114.71 R 143.39 R 206.48
20 R 151.20 R 189.00 R 272.16
25 R 184.36 R 230.45 R 331.85
30 R 215.09 R 268.86 R 387.16
35 R 245.81 R 307.26 R 442.46
40 R 286.78 R 358.48 R 516.20
45 R 322.63 R 403.29 R 580.73
50 R 344.14 R 430.18 R 619.45
55 R 397.08 R 496.35 R 714.74
60 R 430.18 R 537.73 R 774.32
65 R 469.28 R 586.60 R 844.70
70 R 487.52 R 609.40 R 877.54
75 R 516.20 R 645.25 R 929.16
80 R 573.56 R 716.95 R 1,032.41
85 R 595.62 R 744.53 R 1,072.12
90 R 626.82 R 783.53 R 1,128.28
95 R 645.26 R 806.58 R 1,161.47
100 R 696.47 R 870.59 R 1,253.65
Click to go back to contents

POLYURETHANE FOAM – PIC35
PIC35 PIPE SECTION
25MM 30MM 40MM 50MM 60MM 70MM 75MM 80MM 90MM 100MM
INCHES NB MM
0.5 15 22 R 14.40 R 18.65 R 29.52 R 43.06 R 53.68 R 76.54 R 81.05 R 96.88 R 118.10 R 136.26
0.75 20 27 R 16.32 R 20.26 R 31.63 R 44.93 R 62.00 R 78.20 R 83.67 R 97.88 R 126.53 R 146.88
1 25 34 R 18.24 R 22.79 R 35.43 R 46.97 R 65.26 R 81.05 R 96.88 R 103.33 R 130.17 R 158.97
1.25 32 43 R 22.59 R 26.72 R 39.74 R 53.68 R 67.03 R 96.88 R 103.33 R 118.10 R 136.26 R 172.22
1.5 40 50 R 25.05 R 30.62 R 45.93 R 65.26 R 81.05 R 98.41 R 106.08 R 126.53 R 157.96 R 178.14
2 50 61 R 28.70 R 32.63 R 49.21 R 66.96 R 86.11 R 103.33 R 126.53 R 136.26 R 172.22 R 187.88
2.5 65 75 R 36.90 R 43.36 R 59.33 R 81.05 R 103.33 R 126.53 R 136.26 R 158.97 R 175.22 R 228.20
3 80 90 R 45.42 R 51.67 R 72.94 R 91.85 R 110.71 R 136.26 R 147.62 R 172.22 R 187.88 R 248.00
3.5 90 101 R 50.20 R 57.41 R 77.50 R 103.33 R 119.23 R 147.62 R 172.22 R 187.88 R 196.83 R 259.33
4 100 115 R 57.41 R 72.94 R 82.67 R 110.71 R 147.62 R 156.00 R 187.88 R 206.67 R 248.00 R 275.56
4.5 115 127 R 64.58 R 75.15 R 98.41 R 119.23 R 153.23 R 187.88 R 206.67 R 226.45 R 275.56 R 289.30
5 125 142 R 75.15 R 88.57 R 105.98 R 129.17 R 161.04 R 206.67 R 214.79 R 275.56 R 289.37 R 344.44
6 150 169 R 95.38 R 105.98 R 129.17 R 161.04 R 206.67 R 229.63 R 275.26 R 285.13 R 310.00 R 387.50
7 175 190 R 114.81 R 129.17 R 161.04 R 206.67 R 229.63 R 275.56 R 289.37 R 310.00 R 387.50 R 455.00
8 200 219 R 125.25 R 140.91 R 177.14 R 229.93 R 275.56 R 288.37 R 310.00 R 387.50 R 442.86 R 497.88
THICKNESS 110MM 120MM 130MM 140MM 150MM 160MM 170MM 180MM 190MM 200MM
INCH NB MM
0.5 15 22 R 145.61 R 154.96 R 164.31 R 173.66 R 183.01 R 201.01 R 219.01 R 237.01 R 255.01 R 273.01
0.75 20 27 R 156.23 R 165.58 R 174.93 R 184.28 R 193.63 R 211.63 R 229.63 R 247.63 R 265.63 R 283.63
1 25 34 R 168.32 R 177.67 R 187.02 R 196.37 R 205.72 R 223.72 R 241.72 R 259.72 R 277.72 R 295.72
1.25 32 43 R 181.57 R 190.92 R 200.27 R 209.62 R 218.97 R 236.97 R 254.97 R 272.97 R 290.97 R 308.97
1.5 40 50 R 187.49 R 196.84 R 206.19 R 215.54 R 224.89 R 242.89 R 260.89 R 278.89 R 296.89 R 314.89
2 50 61 R 197.23 R 206.58 R 215.93 R 225.28 R 234.63 R 252.63 R 270.63 R 288.63 R 306.63 R 324.63
2.5 65 75 R 237.55 R 246.90 R 256.25 R 265.60 R 279.14 R 292.68 R 306.22 R 319.76 R 333.30 R 346.84
3 80 90 R 257.35 R 266.70 R 276.05 R 285.40 R 298.94 R 312.48 R 326.02 R 339.56 R 353.10 R 366.64
3.5 90 101 R 268.68 R 278.03 R 287.38 R 296.73 R 310.27 R 323.81 R 337.35 R 350.89 R 364.43 R 377.97
4 100 115 R 284.91 R 294.26 R 303.61 R 312.96 R 326.50 R 340.04 R 353.58 R 367.12 R 380.66 R 394.20
4.5 115 127 R 298.65 R 308.00 R 317.35 R 326.70 R 340.24 R 353.78 R 367.32 R 380.86 R 394.40 R 407.94
5 125 142 R 353.79 R 363.14 R 372.49 R 381.84 R 425.38 R 468.92 R 512.46 R 556.00 R 599.54 R 643.08
6 150 169 R 396.85 R 406.20 R 415.55 R 424.90 R 468.44 R 511.98 R 555.52 R 599.06 R 642.60 R 686.14
7 175 190 R 464.35 R 473.70 R 483.05 R 492.40 R 535.94 R 579.48 R 623.02 R 666.56 R 710.10 R 753.64
8 200 219 R 507.23 R 516.58 R 525.93 R 535.28 R 578.82 R 622.36 R 665.90 R 709.44 R 752.98 R 796.52
Click to go back to contents

POLYURETHANE FOAM – PIC35
PIC35 PIPE SECTION
INCH NB MM 25MM 30MM 40MM 50MM 60MM 70MM 75MM 80MM 90MM 100MM
10 250 274 R 172.22 R 196.83 R 205.05 R 258.33 R 354.29 R 442.86 R 476.92 R 505.23 R 516.67 R 606.54
11 275 295 R 193.75 R 221.43 R 295.24 R 354.29 R 387.50 R 470.08 R 516.67 R 540.13 R 563.64 R 620.00
12 300 324 R 221.43 R 295.24 R 354.29 R 355.29 R 442.86 R 516.67 R 540.13 R 620.00 R 688.89 R 776.45
14 350 356 R 221.43 R 265.20 R 332.14 R 463.04 R 583.25 R 688.89 R 688.89 R 845.45 R 966.23 R 1,062.86
16 400 407 R 238.46 R 286.15 R 387.50 R 476.92 R 614.88 R 744.00 R 751.52 R 930.00 R 1,062.86 R 1,082.00
18 450 456 R 254.36 R 300.61 R 389.02 R 506.12 R 635.90 R 763.08 R 847.86 R 918.52 R 1,033.33 R 1,180.95
20 500 508 R 270.15 R 317.14 R 430.56 R 532.19 R 688.89 R 885.71 R 885.71 R 984.13 R 1,192.31 R 1,362.64
22 550 559 R 317.95 R 359.42 R 459.26 R 590.48 R 738.10 R 885.71 R 1,059.83 R 1,059.83 R 1,192.31 R 1,476.19
24 600 610 R 328.04 R 402.60 R 529.91 R 681.32 R 794.87 R 953.85 R 1,148.15 R 1,148.15 R 1,291.57 R 1,610.39
30 750 762 R 408.79 R 442.86 R 635.90 R 817.58 R 953.85 R 1,144.62 R 1,240.00 R 1,377.78 R 1,550.00 R 1,771.43
32 800 812 R 410.83 R 445.07 R 639.08 R 821.67 R 958.62 R 1,150.34 R 1,246.20 R 1,384.67 R 1,557.75 R 1,780.29
34 850 863 R 412.89 R 447.30 R 642.27 R 825.78 R 963.41 R 1,156.09 R 1,252.43 R 1,391.59 R 1,565.54 R 1,789.19
36 900 914 R 425.14 R 450.91 R 652.63 R 845.45 R 978.95 R 1,180.95 R 1,261.02 R 1,488.00 R 1,617.39 R 1,957.89
38 950 965 R 427.27 R 453.16 R 655.89 R 849.68 R 983.84 R 1,186.85 R 1,267.33 R 1,495.44 R 1,625.48 R 1,967.68
40 1000 1016 R 467.65 R 496.00 R 717.89 R 930.00 R 1,076.85 R 1,299.05 R 1,387.12 R 1,636.80 R 1,779.13 R 2,153.68
42 1050 1066 R 514.42 R 545.60 R 789.68 R 1,022.99 R 1,184.53 R 1,428.95 R 1,525.83 R 1,800.48 R 1,957.04 R 2,369.05
48 1200 1220 R 565.86 R 600.16 R 868.65 R 1,125.29 R 1,302.98 R 1,571.84 R 1,678.42 R 1,980.53 R 2,152.75 R 2,605.95
INCH NB MM 110MM 120MM 130MM 140MM 150MM 160MM 170MM 180MM 190MM 200MM
10 250 274 R 628.72 R 650.90 R 673.08 R 695.26 R 717.44 R 851.02 R 1,084.60 R 1,318.18 R 1,551.76 R 1,785.34
11 275 295 R 642.18 R 664.36 R 686.54 R 708.72 R 730.90 R 864.48 R 1,098.06 R 1,331.64 R 1,565.22 R 1,798.80
12 300 324 R 798.63 R 820.81 R 842.99 R 865.17 R 887.35 R 1,020.93 R 1,254.51 R 1,488.09 R 1,721.67 R 1,955.25
14 350 356 R 1,085.04 R 1,107.22 R 1,129.40 R 1,151.58 R 1,173.76 R 1,307.34 R 1,540.92 R 1,774.50 R 2,008.08 R 2,241.66
16 400 407 R 1,104.18 R 1,126.36 R 1,148.54 R 1,170.72 R 1,192.90 R 1,326.48 R 1,560.06 R 1,793.64 R 2,027.22 R 2,260.80
18 450 456 R 1,203.13 R 1,225.31 R 1,247.49 R 1,269.67 R 1,291.85 R 1,425.43 R 1,659.01 R 1,892.59 R 2,126.17 R 2,359.75
20 500 508 R 1,384.82 R 1,407.00 R 1,429.18 R 1,451.36 R 1,473.54 R 1,607.12 R 1,840.70 R 2,074.28 R 2,307.86 R 2,541.44
22 550 559 R 1,498.37 R 1,520.55 R 1,542.73 R 1,564.91 R 1,587.09 R 1,720.67 R 1,954.25 R 2,187.83 R 2,421.41 R 2,654.99
24 600 610 R 1,632.57 R 1,654.75 R 1,676.93 R 1,699.11 R 1,721.29 R 1,954.87 R 2,188.45 R 2,522.03 R 2,855.61 R 3,189.19
30 750 762 R 1,793.61 R 1,815.79 R 1,837.97 R 1,860.15 R 1,882.33 R 2,115.91 R 2,349.49 R 2,683.07 R 3,016.65 R 3,350.23
32 800 812 R 1,802.47 R 1,824.65 R 1,846.83 R 1,869.01 R 1,891.19 R 2,124.77 R 2,358.35 R 2,691.93 R 3,025.51 R 3,359.09
34 850 863 R 1,811.37 R 1,833.55 R 1,855.73 R 1,877.91 R 1,900.09 R 2,133.67 R 2,367.25 R 2,700.83 R 3,034.41 R 3,367.99
36 900 914 R 1,980.07 R 2,002.25 R 2,024.43 R 2,046.61 R 2,068.79 R 2,090.97 R 2,113.15 R 2,135.33 R 2,157.51 R 2,179.69
38 950 965 R 1,989.86 R 2,012.04 R 2,034.22 R 2,056.40 R 2,078.58 R 2,100.76 R 2,122.94 R 2,145.12 R 2,167.30 R 2,189.48
40 1000 1016 R 2,178.08 R 2,202.48 R 2,226.87 R 2,251.27 R 2,275.67 R 2,300.07 R 2,324.47 R 2,348.86 R 2,373.26 R 2,397.66
42 1050 1066 R 2,395.88 R 2,422.72 R 2,449.56 R 2,476.40 R 2,503.24 R 2,530.07 R 2,556.91 R 2,583.75 R 2,610.59 R 2,637.42
48 1200 1220 R 2,635.47 R 2,664.99 R 2,694.52 R 2,724.04 R 2,753.56 R 2,783.08 R 2,812.60 R 2,842.12 R 2,871.65 R 2,901.17
Click to go back to contents

THERMAL INSULATING PLASTER
TPH 300 CEMENT
TPH 300 is a Multi-purpose non asbestos plaster supplied in 40kg bags in a dry powder form. When mixed with clean
water, it dries to a smooth dust free, hard, water resistant finish. No protection from the elements is necessary. If so
desired, it may be painted and can be used both indoors and outside.
TPH 300 can be applied over other plaster or fibre insulations (Blankets or modules), providing it has been covered
and secured with wire mesh or expanded metal in case of flat overhangs.
Best results can be obtained by applying two coats at 5mm thick, allowing the first coat to dry before applying the
second coat.
PRICING
PRODUCT SIZE NEW PRICE
TPH300 CEMENT 40KG R85.00
TPH300 CEMENT 20KG R45.00
Click to go back to contents

HAND CLEANER AND SANITISER
PRODUCT DESCRIPTION
ENVIRO-CLEAN Hand Cleaner is a natural, biodegradable, environmentally friendly hand cleaner.
It cleans hands with a gel based solvent that contains micro beads of foam that act as a pumice
stone. This hand cleaner has a fresh citrus scent and contains no artificial fragrances. The Micro
beads are small enough to get into all areas, tough enough to clean grime, yet light enough to
float away, and will not block drains like other cleaners that contain grit. Hand Cleaners contain
glycerine for skin conditioning.
Description List Price
Industrial Buckets
1kg Bucket R 35.00
2kg Bucket R 63.00
Refill Bottles
1l Bottle R 35.00
2L Bottle R 63.00
5L Bottle R 154.00
Pump Dispenser R 20.00
1kg bucket 2liter refill 2 liter refill
Click to go back to contents with pump

ACCESSORIES
EAR PLUGS GLOVES CHEMICAL GLOVES EAR MUFFS
SAND BLASTING WELDING GOGGLES GRINDING GOGGLES GASWELD GOGGLES
FLIP FRON GOGGLES OVERALLS AND BOILER SUITS RESPIRATORS
REPLACEMENT CARTRIDGE WELDING APRONS WELDING SPATS FFP1 AND FFP2 DUST MASKS
Click to go back to contents

ACCESSORIES
Click to go back to contents

ACCESSORIES
Click to go back to contents

ACCESSORIES
Click to go back to contents

ACCESSORIES
Click to go back to contents

ACCESSORIES
Click to go back to contents

ACCESSORIES
Click to go back to contents

ACCESSORIES
Click to go back to contents

ACCESSORIES – PRICE LIST
ADHESIVES: UNIT: Price ex Vat
Alcolin Filla Foam 500ml R 88.34
Contact Adhesive 5L R 169.00
Contact Adhesive 25L R 796.25
Polyad B603 20L R 470.47
ALUMINIUM FOIL PRODUCTS:
UNIT:
Aluminium Foil 500mmx200mx30microns Roll R 657.80
Aluminium Foil 590mmx200mx30microns Roll R 649.03
Aluminium Foil 660mmx200mx30microns Roll R 724.95
Aluminium Foil 500mmx200mx50microns Roll R 786.07
FASTENERS:
UNIT:
Bonded Washers Galv. 5.5x19mm 1000 R 91.00
Bonded Washers Galv. 5.5x26mm 1000 R 234.00
Bonded Washers S/Steel 5.5x19mm 1000 R 767.00
Drill Stub D/E 3.2mm Each R 4.94
Drill Stub D/E 4.0mm Each R 6.42
Drill Stub D/E 4.8mm Each R 7.77
Drill Stub D/E 5.0mm Each R 9.46
Alluminium Pop Rivets: FAP3210 EC 1000 R 50.70
FAP3212 EC 1000 R 59.80
FAP4812 EC 1000 R 89.70
FAP4815 EC 1000 R 106.60
Steel Pop Rivets: FSP3210 SA 1000 R 18.85
FSP3212 SA 1000 R 208.00
FSP4815 SA 1000 R 377.00
FSP4812 SA 1000 R 273.00
Stainless Steel Pop Rivets: FSSP3208 HAS 1000 R 422.50
FSSP3213 HAS 1000 R 650.00
FSSP4811 HAS 1000 R 1 066.00
FSSP4815 HAS 1000 R 1 170.00
Screws: Selfdrill Hex Tex 12 x 25 1000 R 130.00
12 x 65 1000 R 299.00
Selfdrill Waferhead 10 x 16 1000 R 120.64
Selftapper P/H Slot Galvanized 8 x 13 1000 R 41.60
Selftapper P/H Slot S/Steel 8 x 13 1000 R 175.50
Sockets: Magnetic 5/16” x 65mm Each R 32.50
3/18” x 65mm Each R 32.50
GLASS FIBRE/HI-TEMP. PRODUCTS:
UNIT:
Factory Building Insulation (FR) x 50mm X 10M Roll R 450.45
Click to go back to contents

ACCESSORIES – PRICE LIST
STRAPPING & ACCESSORIES:
UNIT:
Seals – RST Wingtype Galvanized : 10mm 1000 R 123.50
13mm 1000 R 190.44
16mm 1000 R 241.80
19mm 1000 R 219.65
Seals – RST Wingtype Stainless Steel : 10mm 100 R 78.00
12mm 100 R 54.60
16mm 100 R 84.50
19mm 100 R 78.00
Strapping – Galvanized (0.5mm) :10mm Kg R 13.00
13mm Kg R 13.00
16mm Kg R 13.00
19mm Kg R 13.00
Strapping - Stainless Steel (0.5mm) : 10mm x 30m Roll R 78.00
10mm x 200m Roll R 780.00
12mm x 30m Roll R 102.70
12mm x 200m Roll R 780.00
16mm x 30m Roll R 136.50
16mm x 200m Roll R 975.00
19mm x 30m Roll R 149.50
19mm x 200m Roll R 1 128.40
Strapping Machine S260-Bandit Tool 10-19mm Each R 455.00
SEALENTS & COATINGS:
UNIT:
FS3036 Grey/White Antifungus Vapour Barrier Coating(P2191) 25L R 452.40
FS3045 Foamseal/Jointsealer (Mastic) 25Kg R 955.50
FS3045 Foamseal/Jointsealer (M151) 30Kg R 1 092.00
FS3060 Heat Transfer Cement 25Kg R 312.00
Silicone Sealant:- Hi-Temperature 290ml (red) 290ml R 49.69
- Universal(White/Grey/Clear) 280ml R 14.95
Click to go back to contents

ACCESSORIES – PRICE LIST
PAINTBRUSHES & PAINTROLLERS:
UNIT:
H.J Paint Brush:- 25mm Each R 7.45
- 50mm Each R 15.91
- 75mm Each R 23.78
- 100mm Each R 32.63
Radiator Brush(Plastic):- 25mm Each R 12.77
- 38mm Each R 16.15
- 50mm Each R 18.25
- 63mm Each R 21.06
Radiator Brush(Wood):- 25mm Each R 12.77
- 50mm Each R 18.25
- 75mm Each R 21.06
Brazing Brush wooden handle Each R 17.47
Brooms PVC Stiff Platform 460mm Each R 56.78
PAINTROLLERS & REFILLS:
UNIT:
FOR PVA PAINTS: 230mm Sheepskin Roller Each R 48.67
230mm Sheepskin Refill Each R 38.77
150mm Sheepskin Refill Each R 12.32
FOR ENAMEL PAINTS: 225mm Mohair Roller Each R 17.63
225mm Mohair Refill Each R 10.76
160mm Mohair Roller Each R 14.98
160mm Mohair Refill Each R 8.81
100mm Mohair Roller Each R 13.26
100mm Mohair Refill Each R 7.57
ROLLER HANDLES 100MM Each R 5.77
230MM Each R 6.86
Click to go back to contents

ACCESSORIES – PRICE LIST
PAINTERS/BUILDERS TOOLS:
UNIT:
Divider GR Spring:-100mm Each R 38.35
-150mm Each R 55.15
-200mm Each R 74.32
-250mm Each R 95.03
-300mm Each R 109.95
Hammers Ball Pein Each R 35.75
Hammers Chipping Each R 36.70
Hammers Rubber Mallet 450 gram Each R 23.40
Hammers Rubber Mallet 480 gram Each R 42.81
Scriber Eclipse Pocket Each R 62.95
Torpedo Level Magnetic 230mm Each R 11.05
Plier MTS Comb.:-160mm Each R 27.91
-180mm Each R 33.07
-200mm Each R 37.52
Sandpaper P40 x 50m x 300mm Roll R 266.50
Sandpaper P60 x 50m x 300mm Roll R 273.00
Sandpaper P80 x 50m x 300mm Roll R 240.50
Sandpaper P100 x 50m x 300mm Roll R 234.00
Scraper MTS W/Handle:-30mm Each R 7.70
- 40mm Each R 8.44
- 50mm Each R 10.14
- 75mm Each R 11.26
- 90mm Each R 13.34
- 100mm Each R 15.61
Hand Riveter Fascor Each R 103.94
Lazytong Riveter Fascor Each R 385.96
Click to go back to contents

ACCESSORIES – PRICE LIST
PAINTERS/BUILDERS TOOLS CONTINUE:
UNIT:
MTS Rubbercase Tape:- 3m x 16mm Each R 9.75
- 5m x 19mm Each R 16.84
MTS Straight Aviation Tinsnip Each R 34.26
MTS L/Hand Aviation Tinsnip Each R 37.58
MTS R/Hand Aviation Tinsnip Each R 34.45
Raco Straight Aviation Tinsnip Each R 103.60
Raco L/Hand Aviation Tinsnip Each R 100.20
Raco R/Hand Avaition Tinsnip Each R 100.20
Stanley Straight Aviation Tinsnip Each R 95.55
Stanley L/Hand Aviation Tinsnip Each R 95.55
Stanley R/Hand Aviation Tinsnip Each R 95.55
Vicegrip Gedore 175mm Each R 135.41
Vicegrip Gedore 250mm Each R 155.38
Vicegrip MTS 175mm Each R 40.27
Vicegrip MTS 250mm Each R 41.60
Vicegrip Raco 180mm Each R 90.97
Vicegrip Raco 250mm Each R 112.66
TAPES:
UNIT:
Barrier Tape 75mm x 500m Roll R 51.48
Buff Tape: -48mm Roll R 6.34
-72mm Roll R 12.68
Duct Tape: -48mm x 25m Roll R 31.07
Filament Tape: 18mm x 40m Roll R 15.13
18mm x 50m Roll R 21.29
24mm x 40m Roll R 25.01
24mm x 50m Roll R 27.13
Masking Tape: 18mm x 40m Roll R 5.79
24mm x 40m Roll R 7.74
36mm x 40m Roll R 11.64
48mm x 40m Roll R 15.47
Click to go back to contents

ACCESSORIES – PRICE LIST
SUNDRY/MISCELLANEOUS:
UNIT:
Black Plastic Sheeting: - 1mx30mx100microns Roll R 60.00
- 3mx30mx100microns Roll R 119.47
- 4mx30mx250microns Roll R 452.08
- 6mx30mx250microns Roll R 819.00
Batteries: PAN Akl AAA (Remote) Each R 12.79
PAN H/D PENLITE AA Each R 4.71
PAN H/D MEDIUM Size C Each R 8.91
PAN H/D TORCH Size D Each R 11.47
Chrome Caulking Gun Each R 31.20
Cut-off Disc Steel 115x3mm Each R 10.79
Cut-off Disc Steel 230x3mm Each R 11.38
Cut-off Disc Steel 350x3mm Each R 50.18
Grinding Disc Steel 115mmx6mm Each R 9.30
Grinding Disc Steel 230mmx6mm Each R 28.54
Bayonet Globe 100W OSRAM Each R 4.82
Bayonet Globe 150W OSRAM Each R 19.10
Screw-In Globe 100W OSRAM Each R 4.82
Screw-In Globe 150W OSRAM Each R 23.01
Hoseclamp Universal GM4 6-17mm Each R 1.79
Padlock MTS Iron: -20mm Each R 7.74
-25mm Each R 9.22
-32mm Each R 9.98
-38mm Each R 11.62
-50mm Each R 20.45
-63mm Each R 28.95
Yanus Coupler Plug Each R 12.87
3-Pin Rubber Plug Each R 11.05
Electroflex 5mmx100mmx25m Sqm R 21.27
Electroflex 5mmx200mmx25m Sqm R 21.27
Click to go back to contents

ACCESSORIES – PRICE LIST
SUNDRY/MISCELLANEOUS CONTINUE:
UNIT:
Dust Masks FFTP1 Each R 3.73
Cable Ties 100x2.5mm 100 R 6.71
Cable Ties 150x3.5mm 100 R 12.60
Cable Ties 190x4.7mm 100 R 18.72
Cable Ties 310x4.8mm 100 R 34.52
Cable Ties 385x4.7mm 100 R 38.49
Tiger Ski-Rope 10mmx30m Each R 62.45
Tiger Ski-Rope 7mmx30m Each R 29.81
Stainless Steel Breather Springs Each R 50.67
White Polish 20L R 189.28
Vaseline Kg R 48.19
Versi-Sprayfoam Packs Pack R 2 197.00
Manilla Rope (20mm x 25Kg) Kg R 44.20
Hessian Sheeting 7oz (1mx100mx38Kg) Metre R 12.68
Binding Wire Galvanized 50Kg x 1.6mm Roll R 1 021.02
Binding Wire Galvanized 50Kg x 2mm Roll R 603.38
Netting Wire Galvanized 900x13mmx50m Roll R 591.50
Wire pullers Each R 331.01
Cotton Rags (5Kg bags) 5Kg R 14.56
Welding Rods Vitamax 2.5mm (5kg in box) KG R 88.34
Welding Rods Vitamax 3.15mm (5kg in box) KG R 112.11
SAFETY PRODUCTS & SAFETY WEAR
Prices available on request POR POR
POWERTOOLS
Makita Shear JS1660 (straight shear) 1.6mm (260W) Each POR
Makita Nibbler JN1601 1.6mm (550W) Each POR
Click to go back to contents

ACCESSORIES
Click to go back to contents