cover - Encompass Imaging
cover - Encompass Imaging cover - Encompass Imaging
DCR-TRV33/TRV33E 2-13. LB-085 BOARD (REMOVING OF THE EVF)- 3 Caution When attach the Sheet (VF), fold the FP-619 flexible board as shown in the illustration. Sheet (VF) FP-619 flexible board B qa Lamp guide (40) 7 Sheet (VF) q; Cushion LB (40) Two craws 8 FP-619 flexible board Projected part 1 Two screws (M1.7 × 2.5), lock ace, p2 2 Pull out the VF slide assembly fully in the direction of the arrow. VF slide Cabinet (upper) assembly VF slide assembly, etc. 2-14 3 Slide the VF slide cabinet assembly and others once to the deep end, then slant them in the direction of the arrow A to release the claw portion of the VF slide assembly and finally pull them out in the direction of the arrow B and remove them. 6 Remove the LCD cabinet assembly and others from the two dowels and cut-outs of the VF slide assembly. 5 Screw (M1.7 × 2.5), lock ace, p2 VF slide assembly Two dowels Two craws A Cut-outs 9 LB-085 board 4 Screw (M1.7 × 2.5), lock ace, p2 qs Illuminator (40) qf LCX032AN-5 qd Prism sheet (40) qg LCD cabinet assembly
2-14. VA-118 BOARD, LENS SECTION 7 Screw (M1.7 × 2.5), lock ace, p2 FP-620 flexible board Caution When attach the Tape (A), fold the FP-620 flexible board as shown in the illustration. 8 FP-624 flexible board (22P) q; Lens section 9 Lens device LSV-751A (27P) Caution Tape (A) 3 B to B connector (100P) 6 Screw (M1.7 × 2.5), lock ace, p2 When attach the Tape (A), fold the flexible board of the Lens device 751A as shown in the illustration. Lens device LSV-751A Tape (A) 2-15 1 Control switch block (FK-CX4000) (3P) 4 FP-620 flexible board (10P) 2 Two screws (M1.7 × 2.5), lock ace, p2 DCR-TRV33/TRV33E Caution Fold the harness of the control switch block (FK-CX4000) toward the board as shown in the illustration. Harness of the Control switch block (FK-CX4000) 5 VA-118 board, FP-621 flexible board
- Page 1 and 2: SERVICE MANUAL Ver 1.3 2003. 11 Rev
- Page 3 and 4: • SUPPLIED ACCESSORIES Make sure
- Page 5 and 6: 5-1-11. MECHANICAL CHASSIS BLOCK AS
- Page 7 and 8: DCR-TRV33/TRV33E 1-2. SELF-DIAGNOSI
- Page 9 and 10: COVER SECTION 2 DISASSEMBLY HELP Th
- Page 11 and 12: 2-1. P CABINET (C) ASSEMBLY Caution
- Page 13 and 14: 2-3. F PANEL SECTION 3 Open the Cas
- Page 15 and 16: 2-5. CABINET (R) SECTION 4 Three sc
- Page 17 and 18: 2-8. PD-188 BOARD, LCD UNIT 3 Four
- Page 19 and 20: 2-10. BT PANEL/EVF SECTION 1 Screw
- Page 21: 2-12. LB-085 BOARD (REMOVING OF THE
- Page 25 and 26: 2-17. MECHANISM DECK, VC-313 BOARD
- Page 27 and 28: F panel section 40 21 41 20 IC4101
- Page 29 and 30: 2-22.FLEXIBLE BOARDS LOCATION The f
- Page 31 and 32: DCR-TRV33/TRV33E OVERALL SECTION -2
- Page 33 and 34: COVER Link 3. BLOCK DIAGRAMS OVERAL
- Page 35 and 36: DCR-TRV33/TRV33E COVER 3-2. OVERALL
- Page 37 and 38: DCR-TRV33/TRV33E COVER 3-4. OVERALL
- Page 39 and 40: DCR-TRV33/TRV33E COVER 3-6. POWER B
- Page 41 and 42: DCR-TRV33/TRV33E COVER COVER 4-2. S
- Page 43 and 44: COVER Link CD-431 BOARD (CCD IMAGER
- Page 45 and 46: COVER 4-2. SCHEMATIC DIAGRAMS A B C
- Page 47 and 48: COVER For Schematic Diagram • Ref
- Page 49 and 50: COVER For Schematic Diagram • Ref
- Page 51 and 52: COVER For Schematic Diagram • Ref
- Page 53 and 54: COVER For Schematic Diagram • Ref
- Page 55 and 56: A B C D COVER 4-2. SCHEMATIC DIAGRA
- Page 57 and 58: COVER For Schematic Diagram • Ref
- Page 59 and 60: COVER Link 4-3. PRINTED WIRING BOAR
- Page 61 and 62: COVER 4-2. SCHEMATIC DIAGRAMS 4-3.
- Page 63 and 64: COVER 4-2. SCHEMATIC DIAGRAMS 4-3.
- Page 65 and 66: COVER 4-2. SCHEMATIC DIAGRAMS 4-3.
- Page 67 and 68: COVER 4-2. SCHEMATIC DIAGRAMS 4-3.
- Page 69 and 70: COVER 4-2. SCHEMATIC DIAGRAMS 4-3.
- Page 71 and 72: COVER 4-5. MOUNTED PARTS LOCATION C
DCR-TRV33/TRV33E<br />
2-13. LB-085 BOARD (REMOVING OF THE EVF)- 3<br />
Caution<br />
When attach the Sheet (VF),<br />
fold the FP-619 flexible board<br />
as shown in the illustration.<br />
Sheet (VF)<br />
FP-619 flexible<br />
board<br />
B<br />
qa Lamp guide (40)<br />
7 Sheet (VF)<br />
q; Cushion LB (40)<br />
Two craws<br />
8 FP-619 flexible board<br />
Projected part<br />
1 Two screws<br />
(M1.7 × 2.5),<br />
lock ace, p2<br />
2 Pull out the VF slide assembly fully<br />
in the direction of the arrow.<br />
VF slide Cabinet (upper) assembly<br />
VF slide assembly, etc.<br />
2-14<br />
3 Slide the VF slide cabinet assembly and others once<br />
to the deep end, then slant them in the direction of<br />
the arrow A to release the claw portion of the VF slide<br />
assembly and finally pull them out in the direction of the<br />
arrow B and remove them.<br />
6 Remove the LCD cabinet assembly and others from the two dowels and<br />
cut-outs of the VF slide assembly.<br />
5 Screw<br />
(M1.7 × 2.5),<br />
lock ace, p2<br />
VF slide assembly<br />
Two dowels<br />
Two craws<br />
A<br />
Cut-outs<br />
9 LB-085 board<br />
4 Screw<br />
(M1.7 × 2.5),<br />
lock ace, p2<br />
qs Illuminator (40)<br />
qf LCX032AN-5<br />
qd Prism sheet (40)<br />
qg LCD cabinet assembly