catalog TELE - CONTA-CLIP

More documents

Recommendations

Info

WELCOME TO THE WORLD OF THE WATCHDOGS The monitoring relays with the WatchDog label can display electrical values such as current, voltage, power factor, power performance, conductivity, resistance, temperature etc., meaning these can be monitored based on a limit value and deviations displayed on a message contact. The housing is already a sign that the system has a robust design. The overvoltage category is consistently indicated with 3 so that industrial network environments do not present a problem. With the disruptive influences burst and surge, the normative requirements are more than fulfilled. The operating safety of the devices is thus ensured even with high disruption potential. One difference that makes a difference. The temperature range in which the devices can be operated is between –25°C and +55°C. The spacious operating front permits the accommodation of many setting options and display elements. A clear display with a separate LED for each operating mode is thus possible. There is only one rule here, and this has been valid with TELE for years: flashing LED means ‘time running’, continuously illuminated LED means ‘time expired’. The operating elements have a flush arrangement in the front, whereby up to 5 setting elements are possible in a 22.5 mm construction width. This permits maximum functionality on minimum space. As supply variants for the auxiliary voltage, CoolZoom with 24- 240VAC/DC or the power modules with nominal voltages of up to 400V(TR2) or 500V(TR3) are available. The Watchdogs are now also being used in the installation construction form thanks to the ENYA series. With up to 5 setting elements, an excellent operating comfort can be reached in this construction form too that is supplemented by up to four display elements. These can also serve as a diagnosis display in ongoing operation, in order to e.g. recognise in which phase the breakdown has occurred. ENYA devices can fit in every energy distribution cabinet and are thus ideally suited for use in building automation and control systems. They can be used to protect against an unwanted operating status, the detection of consumption points that are switched on or for classical control tasks. The application areas range from the monitoring of a four-wire network via one-phase monitoring applications to DC monitoring of battery-buffered systems. A diversity of current and voltage monitoring relays in one- and three-phase design are available. The supply with these devices is integrated into the measuring circuit to save clamp connections. coolZoom The components mounted in a switching cabinet lead in total to a substantial heat development that has a negative impact on the lifecycle of the entire control unit. Through the use of state-of-the-art switching power supply technology, TELE reduces the energy consumption and thus also the heat development. The typical power consumption of the new products thus lies below the 1W mark – simply ‘cool’. The lower operating temperature firstly has a positive effect on the lifecycle and reliability of the components and secondly results in substantial savings potential in the switching cabinet air climate control system and ventilation. Another benefit is demonstrated in the use of products in battery-buffered systems. Due to the lower power consumption, the battery can be designed in a smaller size with extended follow-up time. With their extreme adaptability (zoom) to any voltage supply in the range of 24 to 240VAC/DC, generous tolerance ranges (20.4 to 264VAC or 19.2 to 300VDC) and their usage options in the frequency range of 16 2/3 to 400Hz, the devices from TELE are suitable for any conceivable application. PowerModules In a simple and cost-effective manner, you adapt the WatchDog monitoring relays and load sentinels and the timing relays of the GAMMA series to the respective supply voltage. The plug-in power modules TR2 and TR3 are available for this and they only have to be inserted into the lateral supply slot of the devices. The power modules TR2, with selectable nominal voltages of 12 to 440VAC, are envisaged for designs in 22.5mm construction width, while the power modules TR3 with nominal voltages of up to 500 V are suitable for types with a 45- mm wide housing. The supply voltage can therefore also be taken up by the outer conductor voltage if a neutral cable is not necessary in the application. The power modules work particularly ‘quietly’ in the network, which means they are entirely suited for class B applications according to EN 55011 (living area). Another advantage: In the event of maintenance, the plug-in power module can be quickly and conveniently replaced. You simply order the right plug-in power modules for your application separately. Page 10 Page 11
SERIES Design GAMMA Industry GAMMA Industry SENSING & MONITORING RELAYS Spannung Strom Temperatur Füllstand 3-phasig 1-phasig 1-phasig 3-phasig Functions Functions Over (OVER) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Over (OVER) Under (UNDER) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Under (UNDER) Window (WIN) • • • • • • • • • • • • • • • • • • • • • • • • • • • Window (WIN) Reverse Window Reverse Window Phase sequence (SEQ) • • • • • • • • • • • • • • Phase sequence (SEQ) Phase failure • • • • • • • • • • • • • • Phase failure Asymmetry (ASYM) • • • • • • • • • • • • • Asymmetry (ASYM) Fault latch (LATCH) • • • • • • • • • • • • • • • • • • • • • • • • • • Fault latch (LATCH) Adjustable thresholds • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Adjustable thresholds Adjustable hysteresis • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Adjustable hysteresis Start-up suppression time (START) • • • • • • • • • • • • • • • • • • Start-up suppression (START) Tripping delay (DELAY) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Tripping delay (DELAY) On delay (ON DELAY) • • • • • • • • • • • • On delay (ON DELAY) Testfunction (TEST/ RESET) • • • • • • • • Testfunction (TEST/ RESET) Short circuit monitoring • • Short circuit monitoring Zero-voltage latch • • Zero-voltage latch Output Output 1 CO contact • • • • • • • • • • • • • • • • 1 CO contact 2 CO contacts • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 2 CO contacts 1 NO contact 1 NO contact cULus - Certificates • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • cULus - Certificates Measured range Measured range 3(N)~ 400/690V AC (48 - 63Hz) 3(N)~ 500V AC (48 - 63Hz) 3(N)~ 230/400V AC (48 - 63Hz) 3(N)~ 230/400V AC (48 - 63Hz) 3(N)~ 230/400V AC (48 - 63Hz) 3(N)~ 132/230V AC (48 - 63Hz) 3(N)~ 132/230V AC (48 - 63Hz) 3(N)~ 66/115V AC (48 - 63Hz) 3(N)~ 66/115V AC (48 - 63Hz) 3~ 230/400V AC (48 - 63Hz) 3~ 208 - 690V AC (48 bis 63Hz) 3(N)~ 230/400V AC (48 - 63Hz) 3N~ 230/400V AC (16,6 - 400Hz) 3(N)~ 230/400V AC (48 - 63Hz) 3(N)~ 132/230V AC (48 - 63Hz) 3(N)~ 66/115V AC (48 - 63Hz) 150V; 300V; 500V AC/DC (16,6 - 400Hz) 30V; 60V; 300V AC/DC (16,6 - 400Hz) 30V; 60V; 300V AC/DC (16,6 - 400Hz) 30V; 60V; 300V AC/DC (16,6 - 400Hz) 60mV; 150mV; 10V AC/DC (16,6 - 400Hz) 30V; 60V; 300V AC/DC (48 - 63Hz) 100mA; 1A; 10A AC/DC (16,6 - 400Hz) 100mA; 1A; 10A AC/DC (16,6 - 400Hz) 100mA; 1A; 10A AC/DC (16,6 - 400Hz) 20mA; 1A; 5A AC/DC (16,6 - 400Hz) 20mA; 1A; 5A AC/DC (16,6 - 400Hz) 20mA; 1A; 5A AC/DC (16,6 - 400Hz) 800mA;1,5A; 2A AC/DC (16,6 - 400Hz) 100mA; 1A; 10A AC/DC (48 - 63Hz) 20mA; 1A; 5A AC/DC (48 - 63Hz) 100mA; 1A; 10A AC/DC (48 - 63Hz) 20mA; 1A; 5A AC/DC (48 - 63Hz) 3~ 5A AC (48 - 63Hz) 3~ 5A AC (48 - 63Hz) PT100 2-/ 3-wire connection -50°C - +200°C ∑R
Page 1 and 2: 15 16 14 17 21 20 19 18 13 12 22 23
Page 3 and 4: US Günther Haase, Founder ERFAHRUN
Page 5: SENSING & MONITORING RELAYS TELE of
Page 9 and 10: FUNCTIONS- OVERVIEW OVER The output
Page 11 and 12: UNDER Undervoltage monitoring Funct
Page 13 and 14: UNDER+SEQ Undervoltage monitoring a
Page 15 and 16: Monitoring of phase sequence, phase
Page 17 and 18: OVER UNDER WIN Overvoltage monitori
Page 19 and 20: OVER UNDER Overcurrent monitoring U
Page 21 and 22: OVER UNDER Overcurrent monitoring U
Page 23 and 24: OVER Monitoring of overtemperature
Page 25 and 26: Temperature monitoring of motor win
Page 27 and 28: Voltage monitoring in 3-phase mains
Page 29 and 30: TUW: AC/DC voltage monitoring in 1-
Page 31 and 32: Temperature monitoring of motor win
Page 33 and 34: K3YM: Voltage monitoring in 1-phase
Page 35 and 36: E1YF400V01 0.85 Voltage monitoring
Page 37 and 38: E1YU, E3YU Undervoltage monitoring
Page 39 and 40: E1PF; E3PF Monitoring of phase sequ
Page 41 and 42: E1IM: DC current monitoring with ad
Page 43 and 44: E3LM10 Level monitoring of conducti
Page 45 and 46: - SERIES Design GAMMA Industrie Tru
Page 47 and 48: 2MIN 2MAX WIN MIN/MAX Underload mon
Page 49 and 50: 2MIN Underload monitoring for two i
Page 51 and 52: Zero Zero Fine setting of zero poin
Page 53 and 54: OVER OVER+LATCH UNDER UNDER+LATCH W
Page 55 and 56: SERIES Design GAMMA Industry DELTA
Page 57 and 58:
Time Relays Series GAMMA Multifunct
Page 59 and 60:
E A nWa nWu nWuWa On delay Off dela
Page 61 and 62:
E ON delay Functions Time Relays Se
Page 63 and 64:
E ON delay R OFF delay with control
Page 65 and 66:
R A OFF delay with control contact
Page 67 and 68:
S Star-Delta start-up Functions Tim
Page 69 and 70:
PDM20; PDM20F; PDM10 E On delay R O
Page 71 and 72:
E R ER ON delay OFF delay with cont
Page 73 and 74:
S Star-Delta start-up Functions Tim
Page 75 and 76:
Emergency light tester Functions Ti
Page 77 and 78:
E R ON delay OFF delay with control
Page 79 and 80:
Wu Single shot leading edge voltage
Page 81 and 82:
More than the sum of individual sen
Page 83 and 84:
OVERVIEW WatchDog pro Module Measur
Page 85 and 86:
The user-defined program is stored
Page 87 and 88:
WatchDog pro module for voltage mea
Page 89 and 90:
WatchDog pro module for current mon
Page 91 and 92:
True power monitoring of 1- and 3-p
Page 93 and 94:
WatchDog pro module with 4 temperat
Page 95 and 96:
WatchDog pro Modul with 4 digital i
Page 97 and 98:
WatchDog pro module with 4 digital
Page 99 and 100:
WatchDog pro module with digital in
Page 101 and 102:
Measured values from the WatchDog p
Page 103 and 104:
Energymanagement Series ECO III Max
Page 105 and 106:
The 8 normally open contacts, as we
Page 107 and 108:
POWER ELECTRONICS OVERVIEW Page Sof
Page 109 and 110:
Softstarter Series ESG Open design
Page 111 and 112:
Thyristor control unit Series ESGT
Page 113 and 114:
Switching Relays Series RA and RM M
Page 115 and 116:
Switching Relays Series SKR Interfa
Page 117 and 118:
Automatic (AUTO) The contact of che
Page 119 and 120:
OVL1 Automatic (AUTO): The contact
Page 121 and 122:
Coupling relay with four independen
Page 123 and 124:
M1MTNI Block diagram Mains decouple
Page 125 and 126:
Time Switches Series TSC < < Daily-
Page 127 and 128:
DC power supply TELE VIP Switching
Page 129 and 130:
Current Transformers Series WSW and
show all

catalog TELE - CONTA-CLIP

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?