catalog TELE - CONTA-CLIP
catalog TELE - CONTA-CLIP
catalog TELE - CONTA-CLIP
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
-<br />
SERIES<br />
Design<br />
GAMMA<br />
Industrie<br />
True power monitors<br />
Current<br />
COSφ - Monitors<br />
Function<br />
Underload detection 5) 5) <br />
Overload detection 5) 5) 1) 1)<br />
Under- and overload detection (Window) 5) 5) 1) 1)<br />
I=0 (zero current-) detection 2) <br />
Temperature monitoring for motor windings <br />
Configurable threshold 5) 5) <br />
Configurable hysteresis 3) 5) 5) <br />
Fault storage 5) 5) <br />
Override on start-up 4) 5) 5) <br />
Tripping delay 5) 5) <br />
Reduced tripping times <br />
Digital control <br />
Outputs<br />
1 CO contact <br />
2 CO contacts <br />
Current rating 16A 16A 12A 12A 12A 12A 12A 12A 12A 12A 15A 10A 2A 10A<br />
Analogue output<br />
Measured voltage<br />
4 -<br />
20mA<br />
4 -<br />
20mA<br />
400/690V AC<br />
400/690V AC<br />
277/480V AC<br />
277/480V AC<br />
277/480V AC<br />
277/480V AC<br />
277/480V AC<br />
230/400V AC<br />
277/480V AC<br />
277/480V AC<br />
230/400V AC<br />
230/400V AC<br />
230/400V AC<br />
Mains voltage<br />
12 - 500V AC<br />
12 - 500V AC<br />
12 - 500V AC<br />
24 - 240V AC/DC<br />
12 - 500V AC<br />
12 - 500V AC<br />
12 - 400V AC<br />
12 - 400V AC<br />
12 - 400V AC<br />
24 - 240V AC/DC<br />
24 - 240V AC/DC<br />
12 - 400V AC<br />
12 - 400V AC<br />
12 - 400V AC<br />
Type<br />
G4BM690V16ATL20<br />
G4BM690V16AL20<br />
G4BM480V12ADTL20<br />
G4BM480V12ADTL20 24-240V AC/DC<br />
G4BM480V12ATL20<br />
G4BM480V12AFTL20<br />
G2BM480V12AFL10<br />
G2BM400V12AL10<br />
G2BM480V12AFL10<br />
G2BA480V12A<br />
G2IA15A<br />
G2CM400V10AL20<br />
G2CM400V2AL20<br />
G2CU400V10AL10<br />
Technical data page 89 89 91 91 93 93 95 95 95 97 99 101 101 101<br />
1) Due to cos φ characteristics maximum detection is only possible within underload range of the motor.<br />
2) Optional detection of disconnected load. A standby condition of the monitoring relay will be triggered.<br />
3) For two-point controller, the differential gap (hysteresis) can be set separately. It‘s the difference between the upper and lower threshold.<br />
4) Time function which disables an error message during start up; this enables a start-up without shut off from inrush load.<br />
5) Monitoring and controlling functions via PLC.<br />
Page 88