Proline Promass 83E/F/O Description of Device Functions - FMC ...

More documents

Recommendations

Info

11 Block SUPERVISION Device Functions Proline Promass 83 11.1 Group SYSTEM 11.1.1 Function group CONFIGURATION SUPERVISION J SYSTEM JAA CONFIGURATION 800 Function description SUPERVISION SYSTEM CONFIGURATION ASSIGN SYSTEM ERROR (8000) Use this function to view all system errors. By selecting a certain system error, its error category can be changed in the subsequent function ERROR CATEGORY (8001). Options: CANCEL List of system errors ! Note! • You can exit this function as follows: select “CANCEL” and confirm with F. • A list of possible system errors is provided in the Operating Instruction Operating Instructions Proline Promass 83, BA 059D/06/en/ ERROR CATEGORY (8001) ! Note! This function is only available if a system error has been selected in the function ASSIGN SYSTEM ERROR (8000). Use this function to define whether a system error triggers a notice message or a fault message. If you select FAULT MESSAGES, all outputs respond to an error in accordance with their defined error response patterns. Options: NOTICE MESSAGES (display only) FAULT MESSAGES (outputs and display) ! Note! Press the key F twice to call up the function ASSIGN SYSTEM ERROR (8000). ASSIGN PROCESS ERROR (8002) Use this function to view all process errors. By selecting an individual process error, its error category can be changed in the subsequent function ERROR CATEGORY (8003). Options: CANCEL List of process errors ! Note! • You can exit this function as follows: select “CANCEL” and confirm with F. • A list of possible process errors is provided in the Operating Instruction Operating Instructions Proline Promass 83, BA 059D/06/en/ Page 180 • MN0M023 Issue/Rev. 0.2 (12/12)
Device Functions Proline Promass 83 11 Block SUPERVISION Function description SUPERVISION SYSTEM CONFIGURATION ERROR CATEGORY (8003) ! Note! This function is only available if a process error has been selected in the function ASSIGN PROCESS ERROR (8002). Use this function to define whether a process error triggers a notice message or a fault message. If you select FAULT MESSAGES, all outputs respond to an error in accordance with their defined error response patterns. Options: NOTICE MESSAGES (display only) FAULT MESSAGES (outputs and display) ! Note! Press the key F twice to call up the function ASSIGN PROCESS ERROR (8002). ACKNOWLEDGE FAULTS (8004) Use this function to define the measuring device's response to fault messages. Options: OFF The measuring device resumes normal operation when the fault is rectified. The fault message automatically disappears from the local display. ON The measuring device resumes normal operation when the fault is rectified. The fault message appears in the local display until it is acknowledged by pressing the F button. Factory setting: OFF ALARM DELAY (8005) Use this function to define a time span for which the criteria for an error have to be satisfied without interruption before a fault or notice message is generated. Depending on the setting and the type of error, this suppression acts on: • Display • Current output • Frequency output •Relay output • Current input User input: 0...100 s (in steps of one second) Factory setting: 0 s " Caution! If this function is activated, fault and notice messages are delayed by the time corresponding to the setting before being transmitted to the higher-order controller (process controller, etc.). It is therefore imperative to check in advance in order to make sure whether a delay of this nature could affect the safety requirements of the process. If fault and notice messages may not be suppressed, a value of 0 seconds must be entered here. Issue/Rev. 0.2 (12/12) MN0M023 • Page 181
Page 1 and 2:
Issue/Rev. 0.2 (12/12) Coriolis Mas
Page 3 and 4:
Device Functions Proline Promass 83
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Esc Device Functions Proline Promas
Page 29 and 30:
Esc Device Functions Proline Promas
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130: Device Functions Proline Promass 83
Page 179: Device Functions Proline Promass 83
show all

Proline Promass 83E/F/O Description of Device Functions - FMC ...

Create successful ePaper yourself

Delete template?

Save as template?