Proline Promass 83E/F/O Description of Device Functions - FMC ...

More documents

Recommendations

Info

9 Block BASIC FUNCTION Device Functions Proline Promass 83 Function description BASIC FUNCTION PROCESS PARAMETER REFERENCE PARAMETER VALUE REFERENCE TEMPERATURE (6464) ! Note! This function is not available unless the CALCULATED REFERENCE DENSITY setting was selected in the CORRECTED VOLUME CALCULATION function (6460). Entering the reference temperature for calculating the corrected volume flow, the corrected volume and the reference density. User input: 5-digit floating-point number Factory setting: 20.000 °C The reference density is calculated as follows: N = · (1 + t + t 2 ) ; where t = t - t N N = Reference density currently measured fluid density (measuring value Promass) t = Actual measured temperature of fluid (measuring value Promass) t N = Reference temperature for calculating the reference density (e.g. 20 °C) = Volumetric expansion coefficient of the fluid, Unit = [1/K]; K = Kelvin = Square volumetric expansion coefficient of the fluid, unit = [1/K 2 ] Page 128 • MN0M023 Issue/Rev. 0.2 (12/12)
Device Functions Proline Promass 83 9 Block BASIC FUNCTION 9.2.4 Function group ADJUSTMENT BASIC FUNCTION G HART GAA PROCESS PARAMETER GIA CONFIGURATION 640 EPD PARAMETER 642 REFERENCE PARAMETER 646 ADJUSTMENT 648 Function description BASIC FUNCTION PROCESS PARAMETER ADJUSTMENT ZEROPOINT ADJUSTMENT (6480) This function enables a zero point adjustment to be automatically carried out. The new zero point determined by the measuring system is adopted by the function ZEROPOINT (see page 135). Options: CANCEL START Factory setting: CANCEL " Caution! Before carrying this out, please refer to the Operating Instructions Proline Promass 83, BA 059D/06/en for a detailed description of the procedure for zero point adjustment. ! Note! • Programming is locked during zero point adjustment. The message“ZERO ADJUST RUNNING” appears on the display. • If the zero point adjustment is not possible (e.g. if v > 0.1 m/s) or has been canceled, the alarm message “ZERO ADJUST NOT POSSIBLE” appears on the display. • If the Promass 83 measuring electronics are fitted with a status input, then the zero point can also be activated by using this input. Issue/Rev. 0.2 (12/12) MN0M023 • Page 129
Page 1 and 2:
Issue/Rev. 0.2 (12/12) Coriolis Mas
Page 3 and 4:
Device Functions Proline Promass 83
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Esc Device Functions Proline Promas
Page 29 and 30:
Esc Device Functions Proline Promas
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78: Device Functions Proline Promass 83
Page 127: Device Functions Proline Promass 83
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
show all

Proline Promass 83E/F/O Description of Device Functions - FMC ...

Create successful ePaper yourself

Delete template?

Save as template?