Proline Promass 83E/F/O Description of Device Functions - FMC ...

More documents

Recommendations

Info

9 Block BASIC FUNCTION Device Functions Proline Promass 83 Function description BASIC FUNCTION PROCESS PARAMETER EPD PARAMETER EPD EXC. CURR. MAX (6426) Use this function to activate the empty pipe detection (EPD). In the event of inhomogeneous fluids or air bubbles, the exciting current of the measuring pipes increases. If the exciting current set in this function is exceeded, error message #700 is output similar to the functions “EPD VALUE LOW (6423)” and “EPD VALUE HIGH (6423).” User input: 5-digit floating-point number Factory setting: 100 mA (deactivated) ! Note! The function is not activated until a value under 100 mA is input. Entering the value 100 mA deactivates the function. Page 126 • MN0M023 Issue/Rev. 0.2 (12/12)
Device Functions Proline Promass 83 9 Block BASIC FUNCTION 9.2.3 Function group REFERENCE PARAMETER BASIC FUNCTION G HART GAA PROCESS PARAMETER GIA CONFIGURATION 640 EPD PARAMETER 642 REFERENCE PARAMETER 646 Function description BASIC FUNCTION PROCESS PARAMETER REFERENCE PARAMETER CORRECTED VOLUME CALCULATION (6460) This function is used to set the reference density for calculating the corrected volume flow. Options: FIXED REFERENCE DENSITY CALCULATED REFERENCE DENSITY EXTERN (with this option, the reference density can be read in via the current input) Factory setting: CALCULATED REFERENCE DENSITY FIXED REF. DENSITY (6461) ! Note! This function is not available unless the FIXED REFERENCE DENSITY setting was selected in the CORRECTED VOLUME CALCULATION function (6460). In this function, a fixed value for the reference density can be entered, with which the corrected volume flow or corrected volume is calculated. User input: 5-digit floating-point number Factory setting: 1 kg/Nl EXPANSION COEFFICIENT (6462) ! Note! This function is not available unless the CALCULATED REFERENCE DENSITY setting was selected in the CORRECTED VOLUME CALCULATION function (6460). For temperature-compensated calculations of the reference density an expansion coefficient specific to the fluid is required and can be entered in this function (see VALUE REFERENCE TEMPERATURE (6464) function on page 128). User input: 5-digit floating-point number Factory setting: 0.5000 e –3 [1/K] EXPANSION COEFFICIENT SQUARE (6463) Use this function to enter a square expansion coefficient, if the temperature compensation follows a nonlinear behavior (see VALUE REFERENCE TEMPERATURE (6464) function on page 128). User input: 5-digit floating-point number Factory setting: 0 e –6 [1/K 2 ] Issue/Rev. 0.2 (12/12) MN0M023 • Page 127
Page 1 and 2:
Issue/Rev. 0.2 (12/12) Coriolis Mas
Page 3 and 4:
Device Functions Proline Promass 83
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Esc Device Functions Proline Promas
Page 29 and 30:
Esc Device Functions Proline Promas
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76: Device Functions Proline Promass 83
Page 125: Device Functions Proline Promass 83
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
show all

Proline Promass 83E/F/O Description of Device Functions - FMC ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?