Proline Promass 83E/F/O Description of Device Functions - FMC ...

More documents

Recommendations

Info

8 Block INPUTS Device Functions Proline Promass 83 8.2.3 Function group INFORMATION INPUTS F STATUS INPUT FAA CURRENT INPUT FCA CONFIGURATION 520 OPERATION 524 INFORMATION 528 Function description INPUTS CURRENT INPUT INFORMATION TERMINAL NUMBER (5280) This function is used to display the polarity and numbers of the terminals (in the terminal compartment) occupied by the current input. Page 118 • MN0M023 Issue/Rev. 0.2 (12/12)
Device Functions Proline Promass 83 9 Block BASIC FUNCTION 9 Block BASIC FUNCTION TAG NAME (6000) p. 120 MANUFACTURER ID (6040) p. 121 ASSIGN LF CUT OFF (6400) p. 122 EMPTY PIPE DETECT. (6420) p. 125 COR. VOL. CALC. (6460) p. 127 ZEROPOINT ADJUST. (6480) p. 129 PRESSURE MODE (6500) p. 132 INST. DIR. SENSOR (6600) p. 133 K-FACTOR (6800) p. 135 TEMPERATURE COEFF. KM (6840) p. 136 DENSITY COEFF. C 0 (6850) p. 137 MIN. FLUID TEMP. (6860) p. 138 TAG DESCRIPTION (6001) p. 120 DEVICE ID (6041) p. 121 ON-VALUE LF CUT OFF (6402) p. 122 EPD VALUE LOW (6423) p. 125 FIXED REF. DENSITY (6461) p. 127 DENSITY ADJUST MODE (6482) p. 130 PRESSURE (6501) p. 132 DENSITY DAMPING (6602) p. 133 ZEROPOINT (6803) p. 135 TEMPERATURE COEFF. KM 2 (6841) p. 136 DENSITY COEFF. C 1 (6851) p. 137 MAX. FLUID TEMP. (6861) p. 138 Function groups CONFIGURATION (600) p. 120 BUS ADDRESS (6002) p. 120 DEVICE REVISION (6042) OFF-VALUE LF CUTOFF (6403) p. 122 EPD VALUE HIGH (6424) p. 125 EXPANS.COEFF. (6462) p. 127 DENSITY SETPOINT 1 (6483) p. 130 FLOW DAMPING (6603) p. 133 NOMINAL DIAMETER (6804) p. 135 TEMPERATURE COEFF. KT (6842) p. 136 DENSITY COEFF. C 2 (6852) p. 137 MIN. CARRIER TEMP. (6862) p. 138 HART PROTOCOL (6003) p. 120 PRESSURE SHOCK SUPPR. (6404) p. 123 EPD RESP. TIME (6425) p. 125 EXP.COEF.SQR. (6463) p. 127 MEASURE FLUID 1 (6484) p. 130 POSITIVE ZERO RET. (6605) p. 133 CALIBRATION COEFF. KD 1 (6843) p. 136 DENSITY COEFF. C 3 (6853) p. 137 MAX. CARRIER TEMP. (6863) p. 138 Functions WRITE PROTECTION (6004) p. 120 EPD EXC. CURR. MAX (6426) p. 126 VALUE REF- TEMP. (6464) p. 128 DENSITY SET VAL2 (6485) p. 130 MEASURE FLUID 2 (6486) p. 130 TEMPERATURE MEASUREMENT (6606) p. 134 CALIBRATION COEFF. KD 2 (6844) p. 136 DENSITY COEFF. C 4 (6854) p. 137 DENSITY COEF. C 5 (6855) p. 137 DENSITY ADJUST REST. ORIGINAL (6487) p. 131 (6488) p. 131 INFORMATION (604) p. 121 CONFIGURATION (640) p. 122 EPD PARAMETER (642) p. 125 REFERENCE PARAMETER (646) p. 127 ADJUSTMENT (648) p. 129 PRESSURE CORRECTION (650) p. 132 CONFIGURATION (660) p. 133 CONFIGURATION (680) p. 135 FLOW COEFF. (684) p. 136 DENSITY COEFF. (685) p. 137 ADDITIONAL COEFF. (686) p. 138 Groups HART (GAA) p. 120 PROCESS PARAMETER (GIA) p. 122 SYSTEM PARAMETER (GLA) p. 133 SENSOR DATA Block BASIC FUNCTION (G) (GNA) p. 135 Issue/Rev. 0.2 (12/12) MN0M023 • Page 119
Page 1 and 2:
Issue/Rev. 0.2 (12/12) Coriolis Mas
Page 3 and 4:
Device Functions Proline Promass 83
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Esc Device Functions Proline Promas
Page 29 and 30:
Esc Device Functions Proline Promas
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68: Device Functions Proline Promass 83
Page 117: Device Functions Proline Promass 83
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
show all

Proline Promass 83E/F/O Description of Device Functions - FMC ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?