MobileAccess2000 TSX Datasheet - Tessco

Datasheet
MobileAccess2000 TSX
Datasheet
The MobileAccess2000 platform provides carriergrade
indoor coverage for a wide range of 2G, 3G,
and 4G mobile voice and data services, over a
single, broadband architecture.
The MA2000 is the leading multi-operator, multiservice
platform, which delivers multiple radio
frequency (RF) services over one common and costeffective
cabling and antenna infrastructure for a
complete solution.
Operator RF services are bi-directionally transmitted
(Uplink/Downlink) between an operator’s capacity
source (BTS/BDA) at the infrastructure head-end
and then distributed to/from remote locations and
multiple buildings, using low-loss fiber and coaxial
cabling media.
Other converged options include WMTS and the
MA2000 system offers MIMO (multi-input/multioutput)
capabilities.
Head-End:
System Controller
Base Unit
Features & Benefits:
Multi-Operator Optimized Platform:
Designed to accommodate multiple operator
requirements separately, yet cost-effectively
across one common infrastructure. Preassembled
modular service packs improve
neutral host ROI for the 1 st carrier in, as well as
the 2 nd and 3 rd .
Multi-Service Platform: Accommodates
virtually any mix of wireless services, eliminating
the need for separate cabled networks for each.
Services include: GSM, CELL, PCS, iDEN, LMR,
SMR, Public Safety, AWS, 700 MHz LTE, Paging,
UMTS, DCS, WMTS, and more.
Modular Design: The MA2000 enables
seamless service upgrades with the addition of a
conditioning card in the head-end and selfcontained
service packs in IDF/Telco/IT closets
at remote-ends.
Scalable Media and MIMO Upgrades:
Additional services leverage the existing coaxial
cabling and antenna grid without disrupting work
spaces or existing services. Fiber links extend a
single capacity source across multiple buildings
in campus environments. Multi-MIMO upgrades
are simple with modular elements.
Carrier-Grade Management: Built-in signal
grooming and an Element Management System
(EMS) offer end-to-end visibility and proactive
alarming, ideal for large scale, multi-operator
environments.
Remote-End:
MA2000 TSX
Service Combiner Unit
DS_MA2000_CE0002301_Rev A00_12AUG10.docx 1

MA2000 System Architecture
The MobileAccess2000 solution is comprised of the following elements. Third-party equipment is sold separately (i.e.
cabling, antennas).
Head-End Equipment
Radio Interface Unit (RIU): The RIU conditions the RF Downlink (DL) signals from an operator’s signal source
(BTS: base-transceiver stations or BDA: bi-directional amplifiers) located inside the building. The RIU then custom
tunes incoming signals in order to ensure a constant level of RF before signals are passed to/from the Base Unit
(BU). RF Uplink (UL) signals from subscribers’ phones are received from the BU and transported back to the
operator’s signal source (BTS or BDA) and to the operator’s macro network outdoors.
Base Unit (BU): The BU converts RF Downlink (DL) signals received from the RIU into an optical signal. This
optical signal is then transported over single or multi-mode fiber optic cabling (SMF/MMF) to/from the MA2000
TSX units, which are housed inside of IDF/Telco/IT closets at the remote-end locations, for distribution throughout
the facility. Uplink (UL) signals from subscribers’ phones are received from the antennas and sent back to the TSX
units through the fiber connection to the head-end, where they are converted back from RF optical to RF electrical
before being passed on to the RIU.
System Controller: The system controller enables centralized remote management and control of all MA2000
elements.
Remote-End Equipment
Tri-Service Package (TSX): The Tri-Service Package (TSX) delivers coverage for three RF services over a
common fiber/coax antenna infrastructure. The output of multiple TSX units can be combined to provide a full
multi-service solution over a common fiber/coax antenna infrastructure. The TSX comes pre-packaged with
applicable filters and other required accessories to simplify the ability to order, service, and install this solution.
The sub-components of the TSX are as follows:
Remote Hub Unit (RHU): The RHU is a services-specific module that performs RF optical to RF electrical
conversion on signals received from the BU. Signals are automatically filtered and amplified for transport over
broadband coax cable to a passive antenna. Uplink (UL) signals from the antennas are then converted to
optical signals before being transmitted back to the BU. Each pre-configured RHU supports up to two
services.
Add-On Module (AO): The AO is a single service module coupled with an RHU to deliver an additional, third
service at a lower incremental cost. The AO receives RF signal from the RHU and amplifies it for transport
across the broadband coax.
Service Combiner Unit (SCU): The Service Combiner Unit is a passive module that combines and distributes
the UL and DL signals from all the MA2000 TSX to the broadband antenna.
DS_MA2000_CE0002301_Rev A00_12AUG10.docx 2

Figure 1: Example MA2000 System Architecture with TSX
DS_MA2000_CE0002301_Rev A00_12AUG10.docx 3

Supported Services
Low Band Services
700 LTE
700/800 Public Safety
Frequency Range (MHz)
Uplink (UL)
698-716
777-787
793-805
806-824
Downlink (DL)
728-757
763-775
851-869
CELL 824-849 869-894
SMR 800 (iDEN 800) 806-824 851-869
SMR 900 (iDEN 900) 896-902 929-941
High Band Services
Frequency Range (MHz)
Uplink (UL)
Downlink (DL)
PCS 1850-1915 1930-1995
AWS 1710-1755 2110-2155
RF Parameters per Service
The RF Parameters listed in the table below are specific to the RHU subcomponent of the MA2000 TSX solution. They
take into account the transmission of the RF through the four-port Service Combiner Unit (P/N SCU-4).
MA2000 TSX RHU RF Parameters
MA2000 RHU
RF Parameter
Max Output Power per
Antenna Port 4
1 (Composite)
700 / 800
Public
Safety
CELL
TDMA /
CDMA /
WCDMA
SMR 800
iDEN 800
Sprint
SMR 900
iDEN 900
Sprint
PCS
GSM /
TDMA
CDMA /
WCDMA
DL UL DL UL DL UL DL UL DL UL DL UL DL UL
14 16 14 10 14 10
2 Carriers 11 13 11 7 11 7 20
4 Carriers 8 10 8 4 8 4 17
8 Carriers 5 7 5 1 5 1 14
12 Carriers 2 5 3 -1 3 -1 11
Mean Gain(dB) 1, 4 14 3 16 7 14 7 10 7 14 7 10 7 9
Pin (dBm) 1 0 0 0 0 0 0 20 3
Input IP3 (dBm) AGC OFF Min -6 -5 -5 -5 -5 -5 0
Input IP3 (dBm) AGC ON Min 6 5 5 5 5 5 -6
SFDR 2 (dB) 71 72 72 71 71 3
Max Intermod Distortion (dBm) -13* -13 -13 -13 -13 64
Max Nf (dB) 20 20 20 20 20 20 -13*
Gain Flatness/Ripple (dB) 3 +/-2.0
* WCDMA compiles with 3GPP TS 25.106 V5.0.0 (2002-03) table 9.4 spectrum emission mask.
1 Factory set mean gain BU-RHU without RIU. May be field adjusted using controller system.
2 SFDR for CDMA services is calculated in 100KB/sec.
3 Gain Flatness/Ripple is specified for the non-duplexed port of the system.
DS_MA2000_CE0002301_Rev A00_12AUG10.docx 4

RF Parameters per Service
The RF Parameters listed in the table below are specific to the AO subcomponent of the MA2000 TSX solution. They take
into account the transmission of the RF through the four-port Service Combiner Unit (P/N SCU-4).
MA2000 TSX Add-On RF Parameters
MA2000 Add-On
RF Parameters
LTE 700 MHz
PCS
CDMA / WCDMA
PCS
GSM / TDMA
AWS
CDMA / WCDMA
DL UL DL UL DL UL DL UL
Max Output Power per Antenna Port
1 (Composite) 21 20 21 21
2 Carriers 18 17 18 18
4 Carriers 15 14 15 15
8 Carriers 11 12 12
12 Carriers 9 10 10
Mean Gain(dB) 1 21 20 3 20 3 21 3
Pin (dBm) 1 0 0 1 0
Max. Intermodulation Distortion (dBm) ** -13* -13 *
Input IP3 (dBm) -10 -7 -7 -7
SFDR (dBm) 2 55 66 64 66
Max NF (dB) 20 18 18 18
Gain Flatness/Ripple (dB) 3 +/-1.0 4 +/-2.0
* WCDMA compiles with 3GPP TS 25.106 V5.0.0 (2002-03) table 9.4 spectrum emission mask.
** Out of band and spurious emissions compliant to FCC.
1 Factory set mean gain BU-RHU without RIU. May be field adjusted using controller system.
2 SFDR for CDMA services is calculated in 100KB/sec.
3 Gain Flatness/Ripple is specified for the non-duplexed port of the system.
4 Gain Flatness/Ripple at any block of the spectrum.
DS_MA2000_CE0002301_Rev A00_12AUG10.docx 5

System Specifications
Absolute Maximum Rating
Total Input RF Power to BU
Total Input RF Power to RHU
Power Supply
Optical Specifications
Optical Output Power
Max. Optical Budget
Optical Loss per Mated-pair
Connectors
10dBm
20dBm out-of-band; -10dBm in-band
60VDC

System Component Specifications
Tri-Service Package (TSX)
The TSX comes fully assembled with an RHU, AO, and applicable filters and accessories. The specifications below reflect
this. As a reference, details of the subcomponents (RHU an AO) are also provided.
Supported Services
Ports
Power
Three services per TSX (1 RHU + 1 AO). Refer to the TSX model
for specific services support.
To Service Combiner Unit: 50Ω QMA cables
Local Power: 100-240VAC (Integrated AC/DC converter)
Remote Power: 25 to 48VDC
Power Consumption: 85W
Physical Characteristics Mounting: 19” Rack mountable (Rack mountable brackets pre-connected)
Dimensions: 51.4cm x 35.0cm x 17.7cm (20.24” x 13.78” x 6.97”)
Weight: 19Kg (42 lb)
Remote Hub Unit
Supported Services
Ports
Power
Two services per RHU
Optical Port to BU: One SC/APC
Input Power: 20 to 48V DC
Power Consumption: 29W
Physical Characteristics Dimensions: 27.9cm x 22.0cm x 4.5cm (10.98” x 8.66” x 1.75”)
Weight: 2.8Kg (6.2 lb)
Add-On
Supported Services
Ports
Input Power
Single service per AO
To RHU: Two pre-connected SMA 50Ω connectors
Input Power: 25 to 48V DC
Power Consumption: 50W
Physical Characteristics Dimensions: 27.9cm x 22.0cm x 6.9cm (10.98” x 8.66” x 2.71”)
Weight: 2.8Kg (6.2 lb)
Service Combiner Unit (4 Port)
Supported Services
High band (1710 MHz - 2155 MHz) and low band (698 MHz – 941 MHz) RF services
Ports
To MA2000 TSX: 8 QMA 50Ω connectors (Terminate if unused)
To Antennas: 4 N-Type 50Ω connectors (Terminate if unused)
Physical Characteristics Dimensions: 16.6cm x 8.0cm x 3.5cm (6.5” x 3.15” x 1.38”)
Comes with bracket that allows it to be mounted directly on top of a MA2000 TSX
DS_MA2000_CE0002301_Rev A00_12AUG10.docx 7

Multimode Fiber Qualifications
50/125 or 62.5/125um complying with ANSI/TIA/EIA-568-B series, EN50173-1 or ISO/IEC 11801, may be used up to 300
meters in length assuming the following qualifications:
Both the Base Unit and Remote Hub Unit must be multimode capable.
All fiber in a given length of fiber must be of the same core diameter.
All bulkhead adapters must be Single-mode SC/APC (Green) adapters.
All terminations, cross connections, or patches must be direct fusion splice or MobileAccess specified patchcords
listed below.
900 Micron Patchcord for Splicing, 2 Meters, 2xSC/APC
62.5/125/900 Diamond p/n ENC/1045341 FiberNext p/n OEM-629002-MAN
50/125/900 Diamond p/n ENC/1045340 FiberNext p/n OEM-509002-MAN
Zipcord Patchcord, 4xSC/APC, 50/125/900/2000/4500 Micron
1Meter Diamond p/n ENC/1045342 FiberNext p/n OEM-50ZIP1-MAN
3 Meter Diamond p/n ENC/1045343 FiberNext p/n OEM-50ZIP3-MAN
Zipcord Patchcord, 4xSC/APC, 62.5/125/900/2000/4500 Micron
1Meter Diamond p/n ENC/1045344 FiberNext p/n OEM-62ZIP1-MAN
3 Meter Diamond p/n ENC/1045345 FiberNext p/n OEM-62ZIP3-MAN
DS_MA2000_CE0002301_Rev A00_12AUG10.docx 8

Ordering Information:
Radio Interface Unit
Part Number
RIU-IM
RIU-BTSC-700LTE
RIU-BTSC-PS700
RIU-BDAC-PS700
RIU-BTSC-CELL
RIU-BDAC-CELL
RIU-BTSC-IDEN
RIU-BDAC-IDEN
RIU-BTSC-PCS
RIU-BDAC-PCS
RIU-BTSC-G -PCS
RIU-BDAC-G-PCS
RIU-BTSC-SMR
RIU-BDAC-SMR
RIU-BTSC-GSM
RIU-BDAC-GSM
RIU-BTSC-GSM-O
RIU-BDAC-GSM-O
RIU-BTSC-DCS
RIU-BDAC-DCS
RIU-BTSC-UMTS
RIU-BTSC-AWS
RIU-BDAC-AWS
RIU-L-IDEN-SMR-G-PCS1
RIU-L-CELL-PCS1
Description
Radio Interface Unit, Support for 1-3 Conditioners
700 LTE Conditioner, 0 to +40dBm Input Range
Public Safety 700 MHz Conditioner, +10 to +36dBm Input Range
Public Safety 700 MHz Conditioner, -16 to +36dBm Input Range
Cellular Conditioner, +10 to +36dBm Input Range
Cellular Conditioner, -16 to +10dBm Input Range
iDEN/SMR800 Conditioner, +10 to +36dBm Input Range
iDEN/SMR800 Conditioner, -16 to +10dBm Input Range
PCS Conditioner, +10 to +36dBm Input Range
PCS Conditioner, -16 to +10dBm Input Range
PCS Conditioner w/ G-Block Support, +10 to +36dBm Input Range
PCS Conditioner w/ G-Block Support, -16 to +10dBm Input Range
SMR900/Paging Conditioner, +10 to +36dBm Input Range
SMR900/Paging Conditioner, -16 to +10dBm Input Range
GSM 900 MHz Conditioner, +10 to +36dBm Input Range
GSM 900 MHz Conditioner, -16 to +10dBm Input Range
GSM 900 MHz Conditioner for Orange, +10 to +36dBm Input Range
GSM 900 MHz Conditioner for Orange, -16 to +10dBm Input Range
DCS 1800 MHz Conditioner, +10 to +36dBm Input Range
DCS 1800 MHz Conditioner, -16 to +10dBm Input Range
UMTS 2100 MHz Conditioner, +10 to +36dBm Input Range
AWS Conditioner, +10 to +36dBm Input Range
AWS Conditioner, -16 to +10dBm Input Range
RIU Lite for iDEN 800,SMR 900, PCS1900 w/G-Block, Support 1BU8, -16 to +10dBm Input
Range
RIU Lite Cellular 800, PCS 1900, -16 to +10dBm Input Range
Base Units
Part Number
WB-B8U
WBM-B8U
WB-B4U
WBM-B4U
Description
Wide Band Base 8 Unit Supporting 8 RHUs
Wide Band Base 8 Unit Supporting 8 RHUs over MMF
Wide Band Base 4 Unit Supporting 4 RHUs
Wide Band Base 4 Unit Supporting 4 RHUs over MMF
DS_MA2000_CE0002301_Rev A00_12AUG10.docx 9

Ordering Information:
MA2000 TSX
Service Supported Part Number Description
700/800 MHz
Public Safety
2000-P71S80-A-TC
2000M-P71S80-A-TC
MA2000 TSX dual-service 700/800 MHz Public Safety.
MA2000 TSX dual-service 700/800 MHz Public Safety with MMF.
700/800 MHz
Public Safety/AWS
CELL/PCS
2000-P71S80A17-A-TC
2000M-P71S80A17-A-TC
2000-C85P19-A-TC
2000M-C85P19-A-TC
MA2000 TSX tri-service 700/800 MHz Public Safety and AWS.
MA2000 TSX tri-service 700/800 MHz Public Safety and AWS with
MMF.
MA2000 TSX dual-service CELL/PCS.
MA2000 TSX tri-service CELL/PCS with MMF.
CELL/PCS/700LTE
CELL/PCS/AWS
IDEN/SMR
IDEN/SMR/PCS
IDEN/SMR/AWS
2000-C85P19L70-A-TC
2000-C85P19L70-A-TC-F
2000M-C85P19L70-A-TC
2000M-C85P19L70-A-TC-F
2000-C85P19A17-A-TC
2000M-C85P19A17-A-TC
2000-S80S90-A-TC
2000M-S80S90-A-TC
2000-S80S90P19-A-TC
2000M-S80S90P19-A-TC
2000-S80S90A17-A-TC
2000M-S80S90A17-A-TC
MA2000 TSX tri-service CELL/PCS and 700 MHz LTE.
- Additional filter (P/N 700LTE-PS-FILTER) ordered separately.
Required if 700/800 MHz Public Safety coexists across same
infrastructure.
MA2000 TSX tri-service CELL/PCS and 700 MHz LTE with filter to
support 700/800 MHz Public Safety coexistence.
MA2000 TSX tri-service CELL/PCS and 700 MHz LTE with filter to
support 700/800 MHz Public Safety coexistence with MMF.
- Additional filter (P/N 700LTE-PS-FILTER) ordered separately.
Required if 700/800 MHz Public Safety coexists across same
infrastructure.
MA2000 TSX tri-service CELL/PCS and 700 MHz LTE with filter to
support 700/800 MHz Public Safety coexistence with filter to support
700/800 MHz Public Safety coexistence and MMF.
MA2000 TSX tri-service CELL/PCS and AWS.
MA2000 TSX tri-service CELL/PCS and AWS with MMF.
MA2000 TSX dual-service 800/900 MHz SMR. Supports 700 MHz LTE
and 700/800 MHz Public Safety coexistence.
MA2000 TSX dual-service 800/900 MHz SMR with MMF. Supports 700
MHz LTE and 700/800 MHz Public Safety coexistence.
MA2000 TSX tri-service 800/900 MHz SMR and PCS. Supports 700
MHz LTE and 700/800 MHz Public Safety coexistence.
MA2000 TSX tri-service 800/900 MHz SMR and PCS with MMF.
Supports 700 MHz LTE and 700/800 MHz Public Safety coexistence.
MA2000 TSX tri-service 800/900 MHz SMR and AWS. Supports 700
MHz LTE and 700/800 MHz Public Safety coexistence.
MA2000 TSX tri-service 800/900 MHz SMR and PCS with MMF.
Supports 700 MHz LTE and 700/800 MHz Public Safety coexistence.
DS_MA2000_CE0002301_Rev A00_12AUG10.docx 10

Ordering Information:
Service Combiner Unit
SCU-4
Part Number
Description
Service Combiner Unit supporting 4 Antenna output ports, 4 Low Band services input ports and 4
High Band services input ports. To be used with the MA2000 TSX solution.
Element Management Components
Part Number
Description
410 Network Controller with Serial Interface (Dial-up)
SC-450
MobileAccess System Controller
Accessories
Optional Filters
Part Number
700LTE-PS-FILTER
Power Supply
Part Number
LPS-48V-66W
LPS-48V-100W
AK-PWR-CORD-EU
AK-PWR-CORD-UK
Description
Cavity filter for the 700LTE Add-On when 700LTE service coexists with 700/800 Public Safety
service across the same set of coax. This filter is already included with the MA2000 TSX
CELL/PCS/700LTE part numbers with a “-F” suffix.
Local AC/DC Converter 66W
Local AC/DC Converter 100W
Description
AC Power Cord for 66W and 100W Power Supplies, European Connector
AC Power Cord for 66W and 100W Power Supplies, UK Connector
www.tessco.com | 800.472.7373
MobileAccess
8391 Old Courthouse Road, Suite 300, Vienna, VA 22182
Tel: +1(866)436-9266, +1(703)848-0200 TAC: +1(800)787-1266, Fax: +1(703)848-0280
www.mobileaccess.com
DS_MA2000_CE0002301_Rev A00_12AUG10.docx 11