MPI Firmware Release Notes - QLogic
MPI Firmware Release Notes - QLogic
MPI Firmware Release Notes - QLogic
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>MPI</strong> <strong>Firmware</strong><br />
Version 1.40.0<br />
<strong>QLogic</strong> Corporation<br />
All rights reserved<br />
Table of Contents<br />
1. Version<br />
2. Changes<br />
3. Bug Fixes<br />
4. Known Issues<br />
5. Additional Information<br />
6. Trademarks<br />
7. Notices<br />
8. Contacting Support<br />
1. Version<br />
These release notes describe the changes, fixes, known issues, and release details that apply to<br />
the <strong>QLogic</strong> message passing interface (<strong>MPI</strong>) firmware, version 1.40.0.<br />
2. Changes<br />
The following changes have been made to the <strong>MPI</strong> firmware between versions 1.38.0 (unreleased)<br />
and 1.40.0 (initial release).<br />
Hardware Support<br />
No changes.<br />
OS Support<br />
No changes.<br />
Software Components<br />
No changes.<br />
Industry Standards Compliance<br />
N/A<br />
<strong>MPI</strong> <strong>Firmware</strong> Version 1.40.0 <strong>Release</strong> <strong>Notes</strong> 1 of 3
3. Bug Fixes<br />
The following table lists the bug fixes made to the <strong>MPI</strong> firmware between versions 1.38.0 and<br />
1.40.0.<br />
Bug Fixes<br />
Error Report<br />
ER69700<br />
ER69731<br />
(ER68092)<br />
ER69710<br />
ER68967<br />
ER69716<br />
ER69778<br />
ER70024<br />
ER68931<br />
ER68841<br />
ER68639<br />
ER69377<br />
ER69356<br />
ER68203<br />
ER70713<br />
ER70821<br />
Description<br />
Port initialization not using the correct sequence (initialize routes before resetting FIFOs; disable all loopback modes as<br />
part of initialization; power up SerDes before processing IFCB).<br />
Config parameter change: enable use of Fibre Channel MAC instead of NIC MAC address. Previously reserved bit 7 of<br />
Port Configuration Options is now defined for this new feature. When this bit is set, Fibre Channel MAC address is used<br />
as the source MAC address for outgoing LLDP/DCBX and Pause frames. When this bit is reset,the NIC MAC address is<br />
used instead.<br />
Allow transmit to be disabled by default. Previously reserved bit 17 of Link Configuration Options is now defined for this<br />
new feature. When this bit is reset, <strong>MPI</strong> comes up with transmit enabled (the default behavior in older firmware). When<br />
this bit is set, <strong>MPI</strong> comes up disabling transmit in SerDes and shuts down the laser output on the optical SFP, causing the<br />
link to go down.<br />
Occasionally no link after switching from internal loopback to external.<br />
<strong>MPI</strong> firmware leaves SCL low after SFP Read/Write mailbox commands.<br />
Get DCBX TLV mailbox command causes <strong>MPI</strong> to hang.<br />
Link fails to come up when using "host init" feature.<br />
Fixed PortID TLV length issue. The function lldpRxProcessFrame was using the Chassis ID length for the<br />
PortID length. Fixed the increment frame pointer to the next TLV before de-referencing the Port ID length.<br />
<strong>MPI</strong> firmware should not automatically enable the SFP transmitter during init and port reset.<br />
SFP access needs to be more robust. Upon SFP insertion, continue to perform VPD validation until successful.<br />
Can report link up when SFP is invalid.<br />
Allow user to enable and disable transmit in Set Port Configuration command. User can also choose to disable transmit<br />
during runtime by issuing Set Port Configuration command with bit 17 set.<br />
No <strong>MPI</strong> linkup event when issuing Set Port Config mailbox command to enable HSS loopback with no transceiver present.<br />
Fixed the error where Set DCBX Control Block mailbox command always returns a 4005h failure status.<br />
Fixed the recovery procedure for FIFO errors so that <strong>MPI</strong> firmware does not hang.<br />
4. Known Issues<br />
The <strong>MPI</strong> firmware, version 1.40.0, has the following known issues:<br />
None.<br />
5. Additional Information<br />
None.<br />
6. Trademarks<br />
Accelera, Accelerating Cluster Performance, FastFabric, InfiniCon Systems, InfiniNIC, InfiniPath,<br />
InfiniView, Intelligent NIC, Networking University, NetXen, QLA, <strong>QLogic</strong>, the <strong>QLogic</strong> logo,<br />
ReadyPath, SANdoctor, SANsurfer, and SilverStorm are registered trademarks of <strong>QLogic</strong><br />
Corporation. To the extent a name or logo does not appear on this list does not constitute a<br />
waiver of any and all intellectual property rights that <strong>QLogic</strong> Corporation or its subsidiaries has<br />
established in any of its product, feature, or service names or logos. All other brand and product<br />
<strong>MPI</strong> <strong>Firmware</strong> Version 1.40.0 <strong>Release</strong> <strong>Notes</strong> 2 of 3
names are trademarks or registered trademarks of their respective owners.<br />
7. Notices<br />
Information furnished in this document is believed to be accurate and reliable. However, <strong>QLogic</strong><br />
Corporation assumes no responsibility for its use, nor for any infringements of patents or other<br />
rights of third parties which may result from its use. <strong>QLogic</strong> Corporation reserves the right to<br />
change product specifications at any time without notice. Applications described in this document<br />
for any of these products are only for illustrative purposes. <strong>QLogic</strong> Corporation makes no<br />
representation nor warranty that such applications are suitable for the specified use without<br />
further testing or modification. <strong>QLogic</strong> Corporation assumes no responsibility for any errors that<br />
may appear in this document.<br />
8. Contacting Support<br />
Please feel free to contact your <strong>QLogic</strong> approved reseller or <strong>QLogic</strong> Technical Support at any phase<br />
of integration for assistance. <strong>QLogic</strong> Technical Support can be reached by the following methods:<br />
Web: http://support.qlogic.com<br />
E-mail: support@qlogic.com<br />
Go to Top<br />
© Copyright 2010. All rights reserved worldwide. <strong>QLogic</strong>, the <strong>QLogic</strong> logo, and the Powered by <strong>QLogic</strong> logo are registered trademarks of<br />
<strong>QLogic</strong> Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners.<br />
<strong>MPI</strong> <strong>Firmware</strong> Version 1.40.0 <strong>Release</strong> <strong>Notes</strong> 3 of 3