Owner's Manual Osburn 2000 Wood Stove Insert - Rural Energy ...

More documents

Recommendations

Info

6. OPENING SIZE: Refer to “Suitable Fireplace Dimensions” (Sec. 2.2) for suitable size fireplace openings. NOTE: A METAL TAG IS PROVIDED AND IS TO BE FASTENED TO THE BACK WALL OF THE FIREPLACE IF THE FIREPLACE HAS BEEN MODIFIED TO ACCOMMODATE THE INSERT. 2.2. VENTING REQUIREMENTS The flue is a critical component to a satisfactory installation. Your insert will attain its best performance if installed with a flue that generates its own draft. The minimum venting requirement will be the installation of a flue connector from the insert into the first tile of the chimney (see Figure 3.3). If you are using a masonry chimney, it is important that it be built in compliance with the specifications of the National Building Code or other applicable standard having jurisdiction. It must be lined with fire clay bricks, metal or clay tiles sealed together with fire cement (round flues are the most efficient). Ideally, the interior diameter of the masonry chimney should be identical to the insert smoke exhaust. You may also run a stainless steel liner inside the masonry chimney. A continuous 6" (152mm) stainless steel liner from the top of the chimney to the insert’s smoke exhaust (see Figure 3.2) is the optimum system and will provide the best performance, as well as compensate for poor draft situations caused by large cross-sectional chimneys. The insert will not work without a positive seal in the chimney. Chimneys constructed outside of the home, on an exterior wall, should be avoided if possible, especially in colder climates. Outside chimneys may not draw as well and may downdraft due to the difficulty in heating them up to operating temperature. Cooler chimneys will result in increased creosoting, less draft, and poorer performance. Draft is proportional to overall chimney height as well as to stack temperature. Draft can be increased by increasing chimney height, and by reducing heat loss from the chimney through an insulated liner. Ensure that all joints in the flue systems are tightly sealed, since any leaks will result in reduced performance as well as a possible safety hazard. Using a fire screen at the extremity of the chimney requires regular inspection in order to insure that it is not obstructed thus blocking the draught, and it should be cleaned when necessary. Do not connect this unit to a chimney flue serving another appliance. This heating unit must serve as a supplementary heat source. An alternate heat source should be available in the home if needed. The manufacturer cannot be responsible for additional heating costs associated with the use of an alternative heat source. It is recommended that the user buys this product from a retailer who can provide installation and maintenance advices. 5
Section 3.0 - INSTALLATION 3.1. CLEARANCES TO COMBUSTIBLES To install your appliance correctly, it is extremely important to respect all clearances to any combustibles as mentioned on your insert certification label. (See figure 3.1 and table 3.1) Figure 3.1 CLEARANCES MINIMUM MASONRY OPENING A 13’’ (330 mm) F 24” (610 mm) B 22’’ (559 mm) G 29” (737 mm) C 10’’ (254 mm) H 16.5” (420 mm) D 29’’ (737 mm) Table 3.1 Note: If side mantle protrudes more than 1.5” (38mm) in front of face of fireplace, then use sidewall clearance. 6
Page 1 and 2: OSBURN 2000-I E.P.A. WOOD INSERT OW
Page 3 and 4: TABLE OF CONTENTS INTRODUCTION ....
Page 5: Section 2.0 - PRE-INSTALLATION REQU
Page 9 and 10: 3.3. SAFETY INFORMATION NOTE: This
Page 11 and 12: 5. If lag-bolts and anchors are to
Page 13 and 14: 3.7. ADAPTER FOR FRESH AIR KIT INST
Page 15 and 16: 3.9. SECONDARY AIR TUBE REPLACEMENT
Page 17 and 18: Section 4.0 OPERATION 4.1. SAFETY I
Page 19 and 20: 4.2. CORDWOOD FUEL 1. Fuel for the
Page 21 and 22: 6. Ideally the large kindling shoul
Page 23 and 24: 4.6. FAN OPERATION 1. The fan in yo
Page 25 and 26: Do not abuse the door glass by stri
Page 27 and 28: Section 6.0 SPECIFICATIONS 6.1. Osb
Page 29 and 30: OSBURN 2000-I E.P.A. WOOD INSERT OW
Page 31 and 32: TABLE OF CONTENTS INTRODUCTION ....
Page 33 and 34: Section 2.0 - PRE-INSTALLATION REQU
Page 35 and 36: Section 3.0 - INSTALLATION 3.1. CLE
Page 37 and 38: 3.3. SAFETY INFORMATION NOTE: This
Page 39 and 40: 5. If lag-bolts and anchors are to
Page 41 and 42: 3.7. ADAPTER FOR FRESH AIR KIT INST
Page 43 and 44: 3.9. SECONDARY AIR TUBE REPLACEMENT
Page 45 and 46: Section 4.0 OPERATION 4.1. SAFETY I
Page 47 and 48: 4.2. CORDWOOD FUEL 1. Fuel for the
Page 49 and 50: 6. Ideally the large kindling shoul
Page 51 and 52: 4.6. FAN OPERATION 1. The fan in yo
Page 53 and 54: Do not abuse the door glass by stri
Page 55 and 56: Section 6.0 SPECIFICATIONS 6.1. Osb
Page 57 and 58:
OSBURN 2000-I E.P.A. WOOD INSERT OW
Page 59 and 60:
TABLE OF CONTENTS INTRODUCTION ....
Page 61 and 62:
Section 2.0 - PRE-INSTALLATION REQU
Page 63 and 64:
Section 3.0 - INSTALLATION 3.1. CLE
Page 65 and 66:
3.3. SAFETY INFORMATION NOTE: This
Page 67 and 68:
5. If lag-bolts and anchors are to
Page 69 and 70:
3.7. ADAPTER FOR FRESH AIR KIT INST
Page 71 and 72:
3.9. SECONDARY AIR TUBE REPLACEMENT
Page 73 and 74:
Section 4.0 OPERATION 4.1. SAFETY I
Page 75 and 76:
4.2. CORDWOOD FUEL 1. Fuel for the
Page 77 and 78:
6. Ideally the large kindling shoul
Page 79 and 80:
4.6. FAN OPERATION 1. The fan in yo
Page 81 and 82:
Do not abuse the door glass by stri
Page 83 and 84:
Section 6.0 SPECIFICATIONS 6.1. Osb
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
show all

Owner's Manual Osburn 2000 Wood Stove Insert - Rural Energy ...

Create successful ePaper yourself

Delete template?

Save as template?