Owner's Manual Osburn 2000 Wood Stove Insert - Rural Energy ...

More documents

Recommendations

Info

Section 1.0 - DIMENSIONS Faceplate fully extended toward the back Faceplate fully extended toward the front 3
Section 2.0 - PRE-INSTALLATION REQUIREMENTS 2.1. MASONRY & ZERO CLEARANCE REQUIREMENTS The masonry fireplace must meet the minimum code requirements, or NFPA 211 or the equivalent for a safe installation. Contact your local Building Inspector for requirements in your area. An inspection of the fireplace should include the following: 1. CONDITION OF THE FIREPLACE AND CHIMNEY: Examine the masonry fireplace and chimney prior to installation to determine that they are free from cracks, loose mortar, creosote deposits, blockage, or other signs of deterioration. If evidence of deterioration is noted, the fireplace or chimney should be upgraded prior to installation. 2. INSTALLATION INTO AN EXISTING FACTORY-BUILT ZERO-CLEARANCE FIREPLACE: It is possible to install a wood insert into an existing factory-built zeroclearance fireplace. However, there currently exists no UL or ULC standard specific to that type of installation. The first thing that must be verified is that the factory-built zero clearance fireplace is listed (it must be certified by a competent certification body such as Omni or Warnock Hersey). It must be suitable for use with solid fuel and nothing in the owner’s manual must specifically prohibit the installation of a fireplace insert. When in doubt, check with the fireplace manufacturer. The installation of the zero-clearance fireplace MUST be thoroughly inspected by a professional in order to ensure that it still meets the manufacturer’s specs and code conformity. The chimney must be of at least 1" (25 mm) larger in diameter to accommodate a required continuous stainless steel liner running from the flue collar to the top of the chimney termination. Never remove parts that serve to insulate the zero-clearance fireplace from combustible material. Only readily detachable parts that are easily replaced, such as damper parts, screens, and doors, are to be removed from the fireplace. These parts must be stored nearby and available for retrofit if the insert is ever removed. Removal of any parts which render the fireplace unfit for use with solid fuel requires the fireplace to be permanently labelled by the installer as being no longer suitable for solid fuel until the removed parts are replaced and the fireplace is restored to its original certified condition. Furthermore, any air vents, grilles, or louvers that serve to create an air circulation pattern around and outside the zero-clearance fireplace shall never be removed. 3. CHIMNEY CAPS: Mesh type chimney caps must have provision for regular cleaning, or the mesh should be removed to eliminate the potential of plugging. 4. LINER: The chimney must have an acceptable masonry liner suitable for solid fuel, otherwise a continuous stainless steel liner must be installed. 5. ADJACENT COMBUSTIBLES: The fireplace should be inspected to make sure that there is adequate clearance to combustibles, both exposed combustibles to the top, side, and front as well as concealed combustibles, in the chimney and mantel area. Your local inspector should have information on whether older fireplaces are of adequate construction. 4
Page 1 and 2:
OSBURN 2000-I E.P.A. WOOD INSERT OW
Page 3 and 4:
TABLE OF CONTENTS INTRODUCTION ....
Page 5 and 6:
Section 2.0 - PRE-INSTALLATION REQU
Page 7 and 8:
Section 3.0 - INSTALLATION 3.1. CLE
Page 9 and 10:
3.3. SAFETY INFORMATION NOTE: This
Page 11 and 12:
5. If lag-bolts and anchors are to
Page 13 and 14:
3.7. ADAPTER FOR FRESH AIR KIT INST
Page 15 and 16:
3.9. SECONDARY AIR TUBE REPLACEMENT
Page 17 and 18:
Section 4.0 OPERATION 4.1. SAFETY I
Page 19 and 20:
4.2. CORDWOOD FUEL 1. Fuel for the
Page 21 and 22:
6. Ideally the large kindling shoul
Page 23 and 24:
4.6. FAN OPERATION 1. The fan in yo
Page 25 and 26:
Do not abuse the door glass by stri
Page 27 and 28:
Section 6.0 SPECIFICATIONS 6.1. Osb
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
3.3. SAFETY INFORMATION NOTE: This
Page 39 and 40:
5. If lag-bolts and anchors are to
Page 41 and 42:
3.7. ADAPTER FOR FRESH AIR KIT INST
Page 43 and 44:
3.9. SECONDARY AIR TUBE REPLACEMENT
Page 45 and 46:
Section 4.0 OPERATION 4.1. SAFETY I
Page 47 and 48:
4.2. CORDWOOD FUEL 1. Fuel for the
Page 49 and 50:
6. Ideally the large kindling shoul
Page 51 and 52:
4.6. FAN OPERATION 1. The fan in yo
Page 53 and 54:
Do not abuse the door glass by stri
Page 55 and 56:
Section 6.0 SPECIFICATIONS 6.1. Osb
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66: 3.3. SAFETY INFORMATION NOTE: This
Page 67 and 68: 5. If lag-bolts and anchors are to
Page 69 and 70: 3.7. ADAPTER FOR FRESH AIR KIT INST
Page 71 and 72: 3.9. SECONDARY AIR TUBE REPLACEMENT
Page 73 and 74: Section 4.0 OPERATION 4.1. SAFETY I
Page 75 and 76: 4.2. CORDWOOD FUEL 1. Fuel for the
Page 77 and 78: 6. Ideally the large kindling shoul
Page 79 and 80: 4.6. FAN OPERATION 1. The fan in yo
Page 81 and 82: Do not abuse the door glass by stri
Page 83 and 84: Section 6.0 SPECIFICATIONS 6.1. Osb
Page 85 and 86: OSBURN 2000-I E.P.A. WOOD INSERT OW
Page 87 and 88: TABLE OF CONTENTS INTRODUCTION ....
Page 89 and 90: Section 2.0 - PRE-INSTALLATION REQU
Page 91 and 92: Section 3.0 - INSTALLATION 3.1. CLE
Page 113 and 114: OSBURN 2000-I E.P.A. WOOD INSERT OW
Page 115: TABLE OF CONTENTS INTRODUCTION ....
Page 119 and 120: Section 3.0 - INSTALLATION 3.1. CLE
show all

Owner's Manual Osburn 2000 Wood Stove Insert - Rural Energy ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?