Tutorial Xilinx Virtex-5 FPGA ML506 Edition

More documents

Recommendations

Info

The files I will be using can be found in: ml506_std_ip_pcores\sw\standalone Right-click the 'src' folder under the play_sine project and click New → Source File: 94
Name the file 'play_sine.c' and click Finish: Delete all the auto-generated comments and put this in (copy and paste this code). The original version can be found in ml506_sdt_ip_pcores\sw\standalone\test_ac97. I cleaned it up and added the ability to choose different frequencies and use the LCD screen (its about 4 ½ pages long): #include #include #include "xio.h" #include "xuartns550_l.h" #include "sleep.h" #include "xparameters.h" #include "lcd.h" #include "memory_map.h" #define UART_CLOCK XPAR_XUARTNS550_CLOCK_HZ #if !SIM #define UART_BAUDRATE 9600 /* real hardware */ #else #define UART_BAUDRATE (UART_CLOCK / 16 / 3) /* simulation */ #endif 95
Page 1 and 2:
Tutorial Xilinx Virtex-5 FPGA ML506
Page 3 and 4:
Blank Page 3
Page 5 and 6:
Setting up the ML506 board The ML50
Page 7 and 8:
• Set SW6 (on the back side of th
Page 9 and 10:
• Go to setup → serial port, an
Page 11 and 12:
Illustration 1: SACE ERR, CF card i
Page 13 and 14:
Once this is complete, right-click
Page 15 and 16:
After connecting your board. Run Te
Page 17 and 18:
The VHDL Design Open up Xilinx ISE.
Page 19 and 20:
Now setup the project settings for
Page 21 and 22:
Select VHDL module and name the fil
Page 23 and 24:
p1
Page 25 and 26:
At the top click on Project → New
Page 27 and 28:
Now that our code is finished we ha
Page 29 and 30:
Programming the FPGA using iMPACT N
Page 31 and 32:
If all is well, you should see the
Page 33 and 34:
That's it! Your 2-bit greater-than
Page 35 and 36:
Creating the Design First make sure
Page 38 and 39:
Once Simulink is open make a new mo
Page 40 and 41:
Now we will create a new compilatio
Page 42 and 43:
Leave the board on and click 'Detec
Page 44 and 45: Click Save and Close, then click 'A
Page 46: Once the installation is complete,
Page 49 and 50: After dragging in the box, a window
Page 51 and 52: Double-click on the System Generato
Page 54 and 55: Click ok. Make sure your board is o
Page 56 and 57: Then you can toggle the GPIO switch
Page 58 and 59: Now within this folder make two emp
Page 60 and 61: In the Project File section point i
Page 62 and 63: Choose the development board, in ou
Page 64 and 65: Choose these default values for the
Page 66 and 67: Click Next on the Cache window as w
Page 68 and 69: The base system is now finished but
Page 70 and 71: Xilinx SDK Close Xilinx XPS and ope
Page 72 and 73: The Xilinx SDK will prompt you to s
Page 74 and 75: In the next window, name the projec
Page 76 and 77: Expand the 'src' folder under the '
Page 78 and 79: Now right-click on the hello_uart p
Page 80 and 81: Turn on the ML506 and open up a ser
Page 82 and 83: Create a folder on the local drive
Page 84 and 85: Then copy these files and put them
Page 86 and 87: Since this Xilinx project was creat
Page 88 and 89: Finally, click Finish: 88
Page 90 and 91: Xilinx SDK Close Xilinx XPS and ope
Page 92 and 93: Name the C project 'play_sine' and
Page 96 and 97: * local prototypes */ volatile int
Page 98 and 99: WriteAC97Reg(AC97_ExtendedAudioStat
Page 100 and 101: XIo_Out32(AC97_InFIFO, j); } } int
Page 102 and 103: Next we need to add some header fil
Page 104 and 105: Program the FPGA Turn on the ML506
Page 106 and 107: Some instructions are also displaye
Page 108 and 109: Create a folder on your local drive
Page 110 and 111: Now we need the bitstream of our pr
Page 112 and 113: Setting up the Compact Flash Make s
Page 114: Since our file is in cfg1, we need
show all

Tutorial Xilinx Virtex-5 FPGA ML506 Edition

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?