Tutorial Xilinx Virtex-5 FPGA ML506 Edition

More documents

Recommendations

Info

Once Simulink is open make a new model by clicking file → New → Model. Make a new folder on your local drive called 'GreaterThanCoSim' then save the model as 'greaterthan' into your newly created folder. 38
In the Simulink Library Browser scroll down to <strong>Xilinx</strong> Blockset and double-click it, then double click on the Index tab. You should see all the available <strong>Xilinx</strong> blocks to create your design. Click and drag the block 'System Generator' into your model editor. 39
Page 1 and 2: Tutorial Xilinx Virtex-5 FPGA ML506
Page 3 and 4: Blank Page 3
Page 5 and 6: Setting up the ML506 board The ML50
Page 7 and 8: • Set SW6 (on the back side of th
Page 9 and 10: • Go to setup → serial port, an
Page 11 and 12: Illustration 1: SACE ERR, CF card i
Page 13 and 14: Once this is complete, right-click
Page 15 and 16: After connecting your board. Run Te
Page 17 and 18: The VHDL Design Open up Xilinx ISE.
Page 19 and 20: Now setup the project settings for
Page 21 and 22: Select VHDL module and name the fil
Page 23 and 24: p1
Page 25 and 26: At the top click on Project → New
Page 27 and 28: Now that our code is finished we ha
Page 29 and 30: Programming the FPGA using iMPACT N
Page 31 and 32: If all is well, you should see the
Page 33 and 34: That's it! Your 2-bit greater-than
Page 35 and 36: Creating the Design First make sure
Page 40 and 41: Now we will create a new compilatio
Page 42 and 43: Leave the board on and click 'Detec
Page 44 and 45: Click Save and Close, then click 'A
Page 46: Once the installation is complete,
Page 49 and 50: After dragging in the box, a window
Page 51 and 52: Double-click on the System Generato
Page 54 and 55: Click ok. Make sure your board is o
Page 56 and 57: Then you can toggle the GPIO switch
Page 58 and 59: Now within this folder make two emp
Page 60 and 61: In the Project File section point i
Page 62 and 63: Choose the development board, in ou
Page 64 and 65: Choose these default values for the
Page 66 and 67: Click Next on the Cache window as w
Page 68 and 69: The base system is now finished but
Page 70 and 71: Xilinx SDK Close Xilinx XPS and ope
Page 72 and 73: The Xilinx SDK will prompt you to s
Page 74 and 75: In the next window, name the projec
Page 76 and 77: Expand the 'src' folder under the '
Page 78 and 79: Now right-click on the hello_uart p
Page 80 and 81: Turn on the ML506 and open up a ser
Page 82 and 83: Create a folder on the local drive
Page 84 and 85: Then copy these files and put them
Page 86 and 87: Since this Xilinx project was creat
Page 88 and 89:
Finally, click Finish: 88
Page 90 and 91:
Xilinx SDK Close Xilinx XPS and ope
Page 92 and 93:
Name the C project 'play_sine' and
Page 94 and 95:
The files I will be using can be fo
Page 96 and 97:
* local prototypes */ volatile int
Page 98 and 99:
WriteAC97Reg(AC97_ExtendedAudioStat
Page 100 and 101:
XIo_Out32(AC97_InFIFO, j); } } int
Page 102 and 103:
Next we need to add some header fil
Page 104 and 105:
Program the FPGA Turn on the ML506
Page 106 and 107:
Some instructions are also displaye
Page 108 and 109:
Create a folder on your local drive
Page 110 and 111:
Now we need the bitstream of our pr
Page 112 and 113:
Setting up the Compact Flash Make s
Page 114:
Since our file is in cfg1, we need
show all

Tutorial Xilinx Virtex-5 FPGA ML506 Edition

Create successful ePaper yourself

Delete template?

Save as template?