Tutorial Xilinx Virtex-5 FPGA ML506 Edition

More documents

Recommendations

Info

Setting up the Compact Flash Make sure that your compact flash is properly formatted, see the beginning of this entire tutorial. Turn of the ML506 and gently remove the compact flash. Insert the compact flash into your compact flash reader and open up the ML50X folder: 112
Pick one of these folder (I chose cfg1) and open it: Inside you will notice some factory files, delete this file and replace it with the my_playsine.ace file we created (note: deleting this file will render the Xilinx Demo program inoperable): Safely eject, the compact flash: Then insert the compact flash back into the ML506. 113
Page 1 and 2:
Tutorial Xilinx Virtex-5 FPGA ML506
Page 3 and 4:
Blank Page 3
Page 5 and 6:
Setting up the ML506 board The ML50
Page 7 and 8:
• Set SW6 (on the back side of th
Page 9 and 10:
• Go to setup → serial port, an
Page 11 and 12:
Illustration 1: SACE ERR, CF card i
Page 13 and 14:
Once this is complete, right-click
Page 15 and 16:
After connecting your board. Run Te
Page 17 and 18:
The VHDL Design Open up Xilinx ISE.
Page 19 and 20:
Now setup the project settings for
Page 21 and 22:
Select VHDL module and name the fil
Page 23 and 24:
p1
Page 25 and 26:
At the top click on Project → New
Page 27 and 28:
Now that our code is finished we ha
Page 29 and 30:
Programming the FPGA using iMPACT N
Page 31 and 32:
If all is well, you should see the
Page 33 and 34:
That's it! Your 2-bit greater-than
Page 35 and 36:
Creating the Design First make sure
Page 38 and 39:
Once Simulink is open make a new mo
Page 40 and 41:
Now we will create a new compilatio
Page 42 and 43:
Leave the board on and click 'Detec
Page 44 and 45:
Click Save and Close, then click 'A
Page 46:
Once the installation is complete,
Page 49 and 50:
After dragging in the box, a window
Page 51 and 52:
Double-click on the System Generato
Page 54 and 55:
Click ok. Make sure your board is o
Page 56 and 57:
Then you can toggle the GPIO switch
Page 58 and 59:
Now within this folder make two emp
Page 60 and 61:
In the Project File section point i
Page 62 and 63: Choose the development board, in ou
Page 64 and 65: Choose these default values for the
Page 66 and 67: Click Next on the Cache window as w
Page 68 and 69: The base system is now finished but
Page 70 and 71: Xilinx SDK Close Xilinx XPS and ope
Page 72 and 73: The Xilinx SDK will prompt you to s
Page 74 and 75: In the next window, name the projec
Page 76 and 77: Expand the 'src' folder under the '
Page 78 and 79: Now right-click on the hello_uart p
Page 80 and 81: Turn on the ML506 and open up a ser
Page 82 and 83: Create a folder on the local drive
Page 84 and 85: Then copy these files and put them
Page 86 and 87: Since this Xilinx project was creat
Page 88 and 89: Finally, click Finish: 88
Page 90 and 91: Xilinx SDK Close Xilinx XPS and ope
Page 92 and 93: Name the C project 'play_sine' and
Page 94 and 95: The files I will be using can be fo
Page 96 and 97: * local prototypes */ volatile int
Page 98 and 99: WriteAC97Reg(AC97_ExtendedAudioStat
Page 100 and 101: XIo_Out32(AC97_InFIFO, j); } } int
Page 102 and 103: Next we need to add some header fil
Page 104 and 105: Program the FPGA Turn on the ML506
Page 106 and 107: Some instructions are also displaye
Page 108 and 109: Create a folder on your local drive
Page 110 and 111: Now we need the bitstream of our pr
Page 114: Since our file is in cfg1, we need
show all

Tutorial Xilinx Virtex-5 FPGA ML506 Edition

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?