ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data
ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data
3-12 Chapter 3: Setup Fdc On Lpt Use this option to enable the primary floppy on the parallel port. 1. Move the cursor to Fdc On Lpt and press Enter. 2. Select the desired setting from the drop-down menu. Disabled Enabled Floppy Disk Controller This option configures the Floppy Disk Controller. Since there is no floppy disk on the terminal, set this option to Disabled. Mode (Port C) This option sets the mode for serial port C. 1. Move the cursor to Mode and press Enter. 2. Select the desired setting from the drop-down menu. Normal IrDA ASK-IR
Chapter 3: Setup 3-13 Base I/O Address (Port C) UsethisoptiontosetthebaseI/OaddressforserialportC. 1. Move the cursor to Base I/O Address and press Enter. 2. Select the desired setting from the drop-down menu. 220 200 3E8 2E8 Interrupt (Port C/D) This option sets the interrupt for serial port C/D. 1. Move the cursor to Interrupt and press Enter. 2. Select the desired setting from the drop-down menu. IRQ 5 IRQ 6 IRQ 7 IRQ 10 IRQ 11 IRQ 15
- Page 36 and 37: 1-22 Chapter 1: Product Overview LC
- Page 38 and 39: 1-24 Chapter 1: Product Overview Ta
- Page 40 and 41: 1-26 Chapter 1: Product Overview Pr
- Page 42 and 43: 1-28 Chapter 1: Product Overview 71
- Page 44 and 45: 1-30 Chapter 1: Product Overview In
- Page 46 and 47: 1-32 Chapter 1: Product Overview Po
- Page 48 and 49: 1-34 Chapter 1: Product Overview It
- Page 50 and 51: 1-36 Chapter 1: Product Overview
- Page 52 and 53: 2-2 Chapter 2: Hardware Installatio
- Page 54 and 55: 2-4 Chapter 2: Hardware Installatio
- Page 56 and 57: 2-6 Chapter 2: Hardware Installatio
- Page 58 and 59: 2-8 Chapter 2: Hardware Installatio
- Page 60 and 61: 2-10 Chapter 2: Hardware Installati
- Page 62 and 63: 2-12 Chapter 2: Hardware Installati
- Page 64 and 65: 2-14 Chapter 2: Hardware Installati
- Page 66 and 67: 7 8 9 4 5 6 1 2 3 2-16 Chapter 2: H
- Page 68 and 69: 7 8 9 4 5 6 1 2 3 2-18 Chapter 2: H
- Page 70 and 71: 2-20 Chapter 2: Hardware Installati
- Page 72 and 73: 2-22 Chapter 2: Hardware Installati
- Page 74 and 75: 2-24 Chapter 2: Hardware Installati
- Page 76 and 77: 3-2 Chapter 3: Setup Entering Setup
- Page 78 and 79: 3-4 Chapter 3: Setup Setup Menus Ma
- Page 80 and 81: 3-6 Chapter 3: Setup Advanced Menu
- Page 82 and 83: 3-8 Chapter 3: Setup Cache System B
- Page 84 and 85: 3-10 Chapter 3: Setup Serial Port x
- Page 88 and 89: 3-14 Chapter 3: Setup Base I/O Addr
- Page 90 and 91: 3-16 Chapter 3: Setup MSR Interrupt
- Page 92 and 93: 3-18 Chapter 3: Setup Large Disk Ac
- Page 94 and 95: 3-20 Chapter 3: Setup Enable Memory
- Page 96 and 97: 3-22 Chapter 3: Setup PCI/PNP UMB R
- Page 98 and 99: 3-24 Chapter 3: Setup Boot menu ret
- Page 100 and 101: 3-26 Chapter 3: Setup Fixed Disk Bo
- Page 102 and 103: 3-28 Chapter 3: Setup Customized Mo
- Page 104 and 105: 3-30 Chapter 3: Setup Boot Menu Opt
- Page 106 and 107: 3-32 Chapter 3: Setup Memory Map Th
- Page 108 and 109: 3-34 Chapter 3: Setup Secondary Mas
- Page 110 and 111: 3-36 Chapter 3: Setup Interrupt IRQ
- Page 112 and 113: 3-38 Chapter 3: Setup DC00 - DFFF P
- Page 114 and 115: 3-40 Chapter 3: Setup
- Page 116 and 117: 4-2 Chapter 4: Operating System Rec
- Page 118 and 119: 4-4 Chapter 4: Operating System Rec
- Page 120 and 121: 4-6 Chapter 4: Operating System Rec
- Page 122 and 123: 4-8 Chapter 4: Operating System Rec
- Page 124 and 125: 4-10 Chapter 4: Operating System Re
- Page 126 and 127: 5-2 Chapter 5: BIOS Updating Proced
- Page 128 and 129: 5-4 Chapter 5: BIOS Updating Proced
- Page 130 and 131: 7 8 9 4 5 6 1 2 3 0 5-6 Chapter 5:
- Page 132 and 133: 5-8 Chapter 5: BIOS Updating Proced
- Page 134 and 135: 5-10 Chapter 5: BIOS Updating Proce
Chapter 3: Setup 3-13<br />
Base I/O Address (Port C)<br />
UsethisoptiontosetthebaseI/OaddressforserialportC.<br />
1. Move the cursor to Base I/O Address and press Enter.<br />
2. Select the desired setting from the drop-down menu.<br />
220<br />
200<br />
3E8<br />
2E8<br />
Interrupt (Port C/D)<br />
This option sets the interrupt for serial port C/D.<br />
1. Move the cursor to Interrupt and press Enter.<br />
2. Select the desired setting from the drop-down menu.<br />
IRQ 5<br />
IRQ 6<br />
IRQ 7<br />
IRQ 10<br />
IRQ 11<br />
IRQ 15