ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data
ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data
3-4 Chapter 3: Setup Setup Menus Main Menu PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit System Time: [10:54:34] Item Specific Help System Date: [05/25/2000] Legacy Diskette A: Legacy Diskette B: Primary Master Primary Slave Secondary Master Secondary Slave System Memory Extended Memory [1.44/1/25 Mb, 3½"] [Disabled] (2168MB) [None] [CD-ROM] [None] 640 KB 162816 KB System Time and Date The BIOS can only set the year up to 2030; however, the hardware continues beyond 2030. To set the date and time, perform the following steps: 1. Move your cursor to the System Time option, enter the desired value, and press Tab or Enter to continue with the next field. 2. Enter the desired date in the System Date fields the same way as the last step. 3. Move the cursor to the Exit Menu, select Save Changes & Exit or Save Changes, andpressEnter.
Chapter 3: Setup 3-5 Legacy Diskette The terminal does not have a flex disk drive. Therefore, this option is unused, even though Setup defaults to 1.44 MB, 3 ½". Primary Master After installing a new hard drive, the system should automatically detect the drive. If this is not done automatically and you need to configure the IDE Adapter, perform the following steps: 1. Move the cursor to Primary Master and press Enter to access the following submenu. Exit Main Submenu PhoenixBIOS Setup Utility Type: [Auto] CHS Format Cylinders: [12416] Heads: [ 15] Sectors: [63] Maximum Capacity: 6007MB LBA Format Multi-Sector Transfers: [16 Sectors] LBA Mode Control: [Enabled] 32 Bit I/O: [Disabled] Transfer Mode: [FPIO 4/DMA 2] Ultra DMA Mode: [Mode 2] 2. Use the F5 and F6 keys to select the Type of hard disk. If Auto is selected, the fields are automatically filled, based on the installed drive. 3. Press ESC to return to the Main Menu. 4. Move the cursor to the Exit Menu, select Exit Saving Changes or Save Changes, andpressEnter.
- Page 28 and 29: 1-14 Chapter 1: Product Overview Wh
- Page 30 and 31: 1-16 Chapter 1: Product Overview In
- Page 32 and 33: 1-18 Chapter 1: Product Overview Be
- Page 34 and 35: 1-20 Chapter 1: Product Overview Pl
- Page 36 and 37: 1-22 Chapter 1: Product Overview LC
- Page 38 and 39: 1-24 Chapter 1: Product Overview Ta
- Page 40 and 41: 1-26 Chapter 1: Product Overview Pr
- Page 42 and 43: 1-28 Chapter 1: Product Overview 71
- Page 44 and 45: 1-30 Chapter 1: Product Overview In
- Page 46 and 47: 1-32 Chapter 1: Product Overview Po
- Page 48 and 49: 1-34 Chapter 1: Product Overview It
- Page 50 and 51: 1-36 Chapter 1: Product Overview
- Page 52 and 53: 2-2 Chapter 2: Hardware Installatio
- Page 54 and 55: 2-4 Chapter 2: Hardware Installatio
- Page 56 and 57: 2-6 Chapter 2: Hardware Installatio
- Page 58 and 59: 2-8 Chapter 2: Hardware Installatio
- Page 60 and 61: 2-10 Chapter 2: Hardware Installati
- Page 62 and 63: 2-12 Chapter 2: Hardware Installati
- Page 64 and 65: 2-14 Chapter 2: Hardware Installati
- Page 66 and 67: 7 8 9 4 5 6 1 2 3 2-16 Chapter 2: H
- Page 68 and 69: 7 8 9 4 5 6 1 2 3 2-18 Chapter 2: H
- Page 70 and 71: 2-20 Chapter 2: Hardware Installati
- Page 72 and 73: 2-22 Chapter 2: Hardware Installati
- Page 74 and 75: 2-24 Chapter 2: Hardware Installati
- Page 76 and 77: 3-2 Chapter 3: Setup Entering Setup
- Page 80 and 81: 3-6 Chapter 3: Setup Advanced Menu
- Page 82 and 83: 3-8 Chapter 3: Setup Cache System B
- Page 84 and 85: 3-10 Chapter 3: Setup Serial Port x
- Page 86 and 87: 3-12 Chapter 3: Setup Fdc On Lpt Us
- Page 88 and 89: 3-14 Chapter 3: Setup Base I/O Addr
- Page 90 and 91: 3-16 Chapter 3: Setup MSR Interrupt
- Page 92 and 93: 3-18 Chapter 3: Setup Large Disk Ac
- Page 94 and 95: 3-20 Chapter 3: Setup Enable Memory
- Page 96 and 97: 3-22 Chapter 3: Setup PCI/PNP UMB R
- Page 98 and 99: 3-24 Chapter 3: Setup Boot menu ret
- Page 100 and 101: 3-26 Chapter 3: Setup Fixed Disk Bo
- Page 102 and 103: 3-28 Chapter 3: Setup Customized Mo
- Page 104 and 105: 3-30 Chapter 3: Setup Boot Menu Opt
- Page 106 and 107: 3-32 Chapter 3: Setup Memory Map Th
- Page 108 and 109: 3-34 Chapter 3: Setup Secondary Mas
- Page 110 and 111: 3-36 Chapter 3: Setup Interrupt IRQ
- Page 112 and 113: 3-38 Chapter 3: Setup DC00 - DFFF P
- Page 114 and 115: 3-40 Chapter 3: Setup
- Page 116 and 117: 4-2 Chapter 4: Operating System Rec
- Page 118 and 119: 4-4 Chapter 4: Operating System Rec
- Page 120 and 121: 4-6 Chapter 4: Operating System Rec
- Page 122 and 123: 4-8 Chapter 4: Operating System Rec
- Page 124 and 125: 4-10 Chapter 4: Operating System Re
- Page 126 and 127: 5-2 Chapter 5: BIOS Updating Proced
Chapter 3: Setup 3-5<br />
Legacy Diskette<br />
The terminal does not have a flex disk drive. Therefore, this option is<br />
unused, even though Setup defaults to 1.44 MB, 3 ½".<br />
Primary Master<br />
After installing a new hard drive, the system should automatically<br />
detect the drive. If this is not done automatically and you need to<br />
configure the IDE Adapter, perform the following steps:<br />
1. Move the cursor to Primary Master and press Enter to access the<br />
following submenu.<br />
Exit Main Submenu<br />
PhoenixBIOS Setup Utility<br />
Type:<br />
[Auto]<br />
CHS Format<br />
Cylinders: [12416]<br />
Heads: [ 15]<br />
Sectors: [63]<br />
Maximum Capacity: 6007MB<br />
LBA Format<br />
Multi-Sector Transfers: [16 Sectors]<br />
LBA Mode Control: [Enabled]<br />
32 Bit I/O: [Disabled]<br />
Transfer Mode: [FPIO 4/DMA 2]<br />
Ultra DMA Mode: [Mode 2]<br />
2. Use the F5 and F6 keys to select the Type of hard disk. If Auto is<br />
selected, the fields are automatically filled, based on the installed<br />
drive.<br />
3. Press ESC to return to the Main Menu.<br />
4. Move the cursor to the Exit Menu, select Exit Saving Changes or Save<br />
Changes, andpressEnter.