ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data
ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data
2-2 Chapter 2: Hardware Installation Installation Restrictions • Before installing the terminal, read and follow the guidelines in the NCR 7455 Retail Terminal Site Preparation Guide (B005-0000-1286) and the NCR Workstation and Peripheral AC Wiring Guide (BST0-2115-53). • Install the terminal near an electrical outlet that is easily accessible. Use the power cord as a power-disconnect device. • Do not permit any object to rest on the power cord. Do not locate the terminal where the power cord can be walked on. • Use a grounding strap or touch a grounded metal object to discharge any static electricity from your body before servicing the terminal. • If the power cord is replaced, it must be replaced with the same type of cord with the protective shroud. • Do not route the power cord through openings with sharp edges. • The power supply in the table top mount has a fan for cooling. Do not block the vents on either side of the rear of the mount. In addition, the terminal has a number of vents to provide cooling to the system. Do not install the unit such that the vents are obstructed or covered. Caution: This unit contains hazardous voltages and should only be serviced by qualified service personnel. Caution: DO NOT connect or disconnect the transaction printer while the terminal is connected to AC power. This can result in system or printer damage.
Chapter 2: Hardware Installation 2-3 Connecting the Cables The cable connectors are located on the underside of the unit, under a cable cover. Accessing the Cable Connectors 1. Tilt the display to access the cable connectors. 2. Loosen the thumbscrews (2) that secures the Cable Cover and remove the cover. Screws (2) 18365
- Page 1 and 2: NCR 7455 Retail Terminal Release 1.
- Page 3 and 4: i Safety Warnings Preface Audience
- Page 5 and 6: iii Table of Contents Chapter 1: Pr
- Page 7 and 8: v Introduction ....................
- Page 9 and 10: vii Memory Map.....................
- Page 11 and 12: ix Revision Record Issue Date Remar
- Page 13: xi Declaration of Conformity Manufa
- Page 16 and 17: 1-2 Chapter 1: Product Overview Ser
- Page 18 and 19: 1-4 Chapter 1: Product Overview Har
- Page 20 and 21: 1-6 Chapter 1: Product Overview •
- Page 22 and 23: 1-8 Chapter 1: Product Overview Har
- Page 24 and 25: 1-10 Chapter 1: Product Overview Li
- Page 26 and 27: 1-12 Chapter 1: Product Overview Ha
- Page 28 and 29: 1-14 Chapter 1: Product Overview Wh
- Page 30 and 31: 1-16 Chapter 1: Product Overview In
- Page 32 and 33: 1-18 Chapter 1: Product Overview Be
- Page 34 and 35: 1-20 Chapter 1: Product Overview Pl
- Page 36 and 37: 1-22 Chapter 1: Product Overview LC
- Page 38 and 39: 1-24 Chapter 1: Product Overview Ta
- Page 40 and 41: 1-26 Chapter 1: Product Overview Pr
- Page 42 and 43: 1-28 Chapter 1: Product Overview 71
- Page 44 and 45: 1-30 Chapter 1: Product Overview In
- Page 46 and 47: 1-32 Chapter 1: Product Overview Po
- Page 48 and 49: 1-34 Chapter 1: Product Overview It
- Page 50 and 51: 1-36 Chapter 1: Product Overview
- Page 54 and 55: 2-4 Chapter 2: Hardware Installatio
- Page 56 and 57: 2-6 Chapter 2: Hardware Installatio
- Page 58 and 59: 2-8 Chapter 2: Hardware Installatio
- Page 60 and 61: 2-10 Chapter 2: Hardware Installati
- Page 62 and 63: 2-12 Chapter 2: Hardware Installati
- Page 64 and 65: 2-14 Chapter 2: Hardware Installati
- Page 66 and 67: 7 8 9 4 5 6 1 2 3 2-16 Chapter 2: H
- Page 68 and 69: 7 8 9 4 5 6 1 2 3 2-18 Chapter 2: H
- Page 70 and 71: 2-20 Chapter 2: Hardware Installati
- Page 72 and 73: 2-22 Chapter 2: Hardware Installati
- Page 74 and 75: 2-24 Chapter 2: Hardware Installati
- Page 76 and 77: 3-2 Chapter 3: Setup Entering Setup
- Page 78 and 79: 3-4 Chapter 3: Setup Setup Menus Ma
- Page 80 and 81: 3-6 Chapter 3: Setup Advanced Menu
- Page 82 and 83: 3-8 Chapter 3: Setup Cache System B
- Page 84 and 85: 3-10 Chapter 3: Setup Serial Port x
- Page 86 and 87: 3-12 Chapter 3: Setup Fdc On Lpt Us
- Page 88 and 89: 3-14 Chapter 3: Setup Base I/O Addr
- Page 90 and 91: 3-16 Chapter 3: Setup MSR Interrupt
- Page 92 and 93: 3-18 Chapter 3: Setup Large Disk Ac
- Page 94 and 95: 3-20 Chapter 3: Setup Enable Memory
- Page 96 and 97: 3-22 Chapter 3: Setup PCI/PNP UMB R
- Page 98 and 99: 3-24 Chapter 3: Setup Boot menu ret
- Page 100 and 101: 3-26 Chapter 3: Setup Fixed Disk Bo
Chapter 2: Hardware Installation 2-3<br />
Connecting the Cables<br />
The cable connectors are located on the underside of the unit, under a<br />
cable cover.<br />
Accessing the Cable Connectors<br />
1. Tilt the display to access the cable connectors.<br />
2. Loosen the thumbscrews (2) that secures the Cable Cover and<br />
remove the cover.<br />
Screws (2)<br />
18365