ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data
ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data
7 8 9 4 5 6 1 2 3 0 5-6 Chapter 5: BIOS Updating Procedures Recovery Procedures 1. Connect the Parallel I/F Cable to the parallel (Customer Display) connector on the terminal. Com1 Parallel Port 19505 Note: The parallel connector on the 7455 terminal is used for the Customer Display. If the terminal is equipped with a Customer Display you must temporarily disconnect the display cable. 2. Connect the two machines with the RS-232 cable. Use COM Port 1 on both machines. PC NCR 7455 RS-232 Cable Parallel I/F Cable Parallel Dongle 19504
Chapter 5: BIOS Updating Procedures 5-7 3. Connect the Parallel Dongle to the Parallel I/F Cable. Parallel Dongle 25-pin D-Shell Receptacle 497-0411000 28-pin Sub-Miniature D-Plug Parallel Port 4. Boot the PC in the DOS mode with CD-ROM support. Note: ThePCmustberunningintheDOSmode(notina Windows DOS box) for the software to operate correctly. 16992 5. Insert the BIOS update CD into the PC. NCR BIOS and BIOS Update Software LPIN: A370-0022-0100 6. Apply power to the terminal. 7. On the PC, change directory to the CD-ROM drive. E: [Enter] 8. Enter the update command: EMBflash [Enter] 9. Select the number for the 7455 terminal from the menu list: 1) 7454 2) 7401 3) 7452 4) 7453 5) 7455 6) 7460 7) 7451 8) 7456 5 [Enter]
- Page 80 and 81: 3-6 Chapter 3: Setup Advanced Menu
- Page 82 and 83: 3-8 Chapter 3: Setup Cache System B
- Page 84 and 85: 3-10 Chapter 3: Setup Serial Port x
- Page 86 and 87: 3-12 Chapter 3: Setup Fdc On Lpt Us
- Page 88 and 89: 3-14 Chapter 3: Setup Base I/O Addr
- Page 90 and 91: 3-16 Chapter 3: Setup MSR Interrupt
- Page 92 and 93: 3-18 Chapter 3: Setup Large Disk Ac
- Page 94 and 95: 3-20 Chapter 3: Setup Enable Memory
- Page 96 and 97: 3-22 Chapter 3: Setup PCI/PNP UMB R
- Page 98 and 99: 3-24 Chapter 3: Setup Boot menu ret
- Page 100 and 101: 3-26 Chapter 3: Setup Fixed Disk Bo
- Page 102 and 103: 3-28 Chapter 3: Setup Customized Mo
- Page 104 and 105: 3-30 Chapter 3: Setup Boot Menu Opt
- Page 106 and 107: 3-32 Chapter 3: Setup Memory Map Th
- Page 108 and 109: 3-34 Chapter 3: Setup Secondary Mas
- Page 110 and 111: 3-36 Chapter 3: Setup Interrupt IRQ
- Page 112 and 113: 3-38 Chapter 3: Setup DC00 - DFFF P
- Page 114 and 115: 3-40 Chapter 3: Setup
- Page 116 and 117: 4-2 Chapter 4: Operating System Rec
- Page 118 and 119: 4-4 Chapter 4: Operating System Rec
- Page 120 and 121: 4-6 Chapter 4: Operating System Rec
- Page 122 and 123: 4-8 Chapter 4: Operating System Rec
- Page 124 and 125: 4-10 Chapter 4: Operating System Re
- Page 126 and 127: 5-2 Chapter 5: BIOS Updating Proced
- Page 128 and 129: 5-4 Chapter 5: BIOS Updating Proced
- Page 132 and 133: 5-8 Chapter 5: BIOS Updating Proced
- Page 134 and 135: 5-10 Chapter 5: BIOS Updating Proce
- Page 136 and 137: A-2 Appendix A: Cables Corporate ID
- Page 138 and 139: B-2 Appendix B: Feature Kits Kit Nu
- Page 140 and 141: B-4 Appendix B: Feature Kits
- Page 142: Index-2 —O— Operating System Re
7 8 9<br />
4 5 6<br />
1 2 3<br />
0<br />
5-6 Chapter 5: BIOS Updating Procedures<br />
<strong>Re</strong>covery Procedures<br />
1. Connect the Parallel I/F Cable to the parallel (Customer Display)<br />
connector on the terminal.<br />
Com1<br />
Parallel Port<br />
19505<br />
Note: The parallel connector on the <strong>7455</strong> terminal is used for the<br />
Customer Display. If the terminal is equipped with a Customer<br />
Display you must temporarily disconnect the display cable.<br />
2. Connect the two machines with the RS-232 cable. Use COM Port 1<br />
on both machines.<br />
PC<br />
NCR <strong>7455</strong><br />
RS-232 Cable<br />
Parallel I/F Cable<br />
Parallel Dongle<br />
19504