ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data
ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data ncr/doc/RealPOS/7455/Technical_Manuals/7455_Re... - Alsys Data
4-4 Chapter 4: Operating System Recovery Completing the OS Installation (Windows NT) The system automatically reboots when the image recovery is complete and starts the software installation. This installation also installs most of the additional software and drivers that are included in the disk image. Complete the installation as follows. 1. After the terminal reboots, press Next at the Windows Setup screen. 2. Accept the Microsoft license agreement. 3. Enter the User Name and Organization. 4. Enter the Computer Name for the client. 5. Enter the Administrator’s Account Password (optional). 6. When prompted, press Finish to reboot the client. 7. Loginwhenprompted. 8. Open the Control Panel and run the MicroTouch screen calibration. Completing the OS Installation (Windows 98) The system automatically reboots when the image recovery is complete and starts the software installation. This installation also installs most of the additional software and drivers that are included in the disk image. Complete the installation as follows. 1. When the terminal boots it enters the Windows setup routine. 2. At the User Information screen, enter the User information. This can be done using a keyboard or you can use the touch screen keyboard. After entering the information, press Enter or touch OK. 3. Open Control Panel and set the terminal Date and Time. 4. In the Control Panel, run the MicroTouch screen calibration (if touch-screen equipped).
Chapter 4: Operating System Recovery 4-5 Completing the OS Installation (Windows 2000) The system automatically reboots when the image recovery is complete and starts the software installation. This installation also installs most of the additional software and drivers that are included in the disk image. Complete the installation as follows. 1. After the terminal reboots, press Next at the Windows Setup screen. 2. At the User Information screen, enter the User information. This can be done using a keyboard or you can use the touch screen keyboard. After entering the information, press Enter or touch OK. 3. Open the Control Panel and run the MicroTouch screen calibration (if touch-screen equipped). Completing the OS Installation (DOS) The system automatically reboots when the image recovery is complete and opens at the DOS C: prompt.
- Page 68 and 69: 7 8 9 4 5 6 1 2 3 2-18 Chapter 2: H
- Page 70 and 71: 2-20 Chapter 2: Hardware Installati
- Page 72 and 73: 2-22 Chapter 2: Hardware Installati
- Page 74 and 75: 2-24 Chapter 2: Hardware Installati
- Page 76 and 77: 3-2 Chapter 3: Setup Entering Setup
- Page 78 and 79: 3-4 Chapter 3: Setup Setup Menus Ma
- Page 80 and 81: 3-6 Chapter 3: Setup Advanced Menu
- Page 82 and 83: 3-8 Chapter 3: Setup Cache System B
- Page 84 and 85: 3-10 Chapter 3: Setup Serial Port x
- Page 86 and 87: 3-12 Chapter 3: Setup Fdc On Lpt Us
- Page 88 and 89: 3-14 Chapter 3: Setup Base I/O Addr
- Page 90 and 91: 3-16 Chapter 3: Setup MSR Interrupt
- Page 92 and 93: 3-18 Chapter 3: Setup Large Disk Ac
- Page 94 and 95: 3-20 Chapter 3: Setup Enable Memory
- Page 96 and 97: 3-22 Chapter 3: Setup PCI/PNP UMB R
- Page 98 and 99: 3-24 Chapter 3: Setup Boot menu ret
- Page 100 and 101: 3-26 Chapter 3: Setup Fixed Disk Bo
- Page 102 and 103: 3-28 Chapter 3: Setup Customized Mo
- Page 104 and 105: 3-30 Chapter 3: Setup Boot Menu Opt
- Page 106 and 107: 3-32 Chapter 3: Setup Memory Map Th
- Page 108 and 109: 3-34 Chapter 3: Setup Secondary Mas
- Page 110 and 111: 3-36 Chapter 3: Setup Interrupt IRQ
- Page 112 and 113: 3-38 Chapter 3: Setup DC00 - DFFF P
- Page 114 and 115: 3-40 Chapter 3: Setup
- Page 116 and 117: 4-2 Chapter 4: Operating System Rec
- Page 120 and 121: 4-6 Chapter 4: Operating System Rec
- Page 122 and 123: 4-8 Chapter 4: Operating System Rec
- Page 124 and 125: 4-10 Chapter 4: Operating System Re
- Page 126 and 127: 5-2 Chapter 5: BIOS Updating Proced
- Page 128 and 129: 5-4 Chapter 5: BIOS Updating Proced
- Page 130 and 131: 7 8 9 4 5 6 1 2 3 0 5-6 Chapter 5:
- Page 132 and 133: 5-8 Chapter 5: BIOS Updating Proced
- Page 134 and 135: 5-10 Chapter 5: BIOS Updating Proce
- Page 136 and 137: A-2 Appendix A: Cables Corporate ID
- Page 138 and 139: B-2 Appendix B: Feature Kits Kit Nu
- Page 140 and 141: B-4 Appendix B: Feature Kits
- Page 142: Index-2 —O— Operating System Re
Chapter 4: Operating System <strong>Re</strong>covery 4-5<br />
Completing the OS Installation (Windows 2000)<br />
The system automatically reboots when the image recovery is complete<br />
and starts the software installation. This installation also installs most<br />
of the additional software and drivers that are included in the disk<br />
image. Complete the installation as follows.<br />
1. After the terminal reboots, press Next at the Windows Setup screen.<br />
2. At the User Information screen, enter the User information. This<br />
can be done using a keyboard or you can use the touch screen<br />
keyboard. After entering the information, press Enter or touch OK.<br />
3. Open the Control Panel and run the MicroTouch screen calibration<br />
(if touch-screen equipped).<br />
Completing the OS Installation (DOS)<br />
The system automatically reboots when the image recovery is complete<br />
and opens at the DOS C: prompt.