SmartLam GL18C Brochure - Tilling Timber
SmartLam GL18C Brochure - Tilling Timber SmartLam GL18C Brochure - Tilling Timber
SINGLE SPAN FLOOR BEARERS SUPPORTING FLOOR LOADS ONLY FLOOR BEARER Floor mass - 40 kg/m 2 Floor Joist EXAMPLE: single span bearer = 4000 mm floor load width = 6000 mm Enter single span table at 6000 mm in floor load width column, read down to a span equal to or greater than 4000 mm Bearer Span ADOPT: SmartLam GL18 - 330x65 mm Floor Load Width Loadings: Permanent - self weight + 40 kg/m 2 + 0.6 kPa of the live load, live load - 1.5 kPa or floor point load of 1.8 kN Note: Not all sizes of SmartLam GL18 in this table are stocked in each state. Please check with your supplier before ordering. Floor load width (mm) 1200 1800 2400 3000 3600 4200 4800 5400 6000 6600 Member size DxB (mm) Floor mass (kg/m 2 ) Maximum Bearer span (mm) Single span 150x65 40 3300 2850 2550 2350 2200 2100 2000 1900 1850 1750 180x65 40 3900 3450 3100 2850 2700 2550 2400 2300 2200 2150 210x65 40 4400 3950 3650 3400 3150 3000 2850 2700 2600 2500 240x65 40 4950 4400 4050 3800 3600 3450 3250 3100 3000 2900 270x65 40 5500 4900 4500 4200 4000 3800 3650 3550 3400 3250 300x65 40 6050 5350 4900 4600 4350 4150 4000 3850 3750 3650 330x65 40 6600 5850 5350 5000 4750 4500 4350 4200 4050 3950 360x65 40 7150 6300 5800 5400 5100 4850 4700 4500 4350 42505 390x65 40 7700 6800 6200 5800 5500 5250 5000 4850 46505 455010 420x65 40 8300 7300 6650 6200 5850 5600 5350 5150 5 5000 5 4850 10 450x65 40 8900 7800 7100 6650 6250 5950 5700 5 5500 5 5300 10 5150 15 480x65 40 9500 8300 7600 7050 6650 6300 60505 580010 560015 545015 510x65 40 10050 8850 8050 7450 7050 67005 640010 615010 595015 575020 150x85 40 3600 3100 2800 2600 2450 2300 2200 2100 2000 1950 180x85 40 4200 3750 3400 3150 2950 2800 2650 2550 2450 2350 210x85 40 4750 4250 3900 3700 3450 3250 3100 2950 2850 2750 240x85 40 5350 4750 4400 4100 3900 3750 3600 3400 3300 3150 270x85 40 5900 5250 4850 4550 4300 4100 3950 3800 3700 3600 300x85 40 6500 5800 5300 4950 4700 4500 4300 4150 4050 3900 330x85 40 7100 6300 5800 5400 5100 4900 4700 4500 4350 4250 360x85 40 7750 6850 6250 5850 5500 5250 5050 4850 4700 4550 390x85 40 8350 7350 6750 6300 5950 5650 5400 5200 5050 4900 420x85 40 9000 7900 7250 6750 6350 6050 5800 5550 5400 5200 450x85 40 9650 8500 7750 7200 6800 6450 6150 5950 5750 5550 5 480x85 40 10250 9050 8250 7650 7200 6850 6550 6300 6100 5 5900 10 510x85 40 10750 9650 8750 8150 7650 7250 6950 66505 64505 625010 540x85 40 11200 10150 9300 8600 8100 7700 73505 70505 680010 655015 570x85 40 11700 10550 9800 9100 8550 8100 7750 5 7400 10 7150 10 6900 15 SmartLam G18C Design Guide 14
CONTINUOUS SPAN FLOOR BEARERS SUPPORTING FLOOR LOADS ONLY Floor mass - 40 kg/m 2 Loadings: Permanent - self weight + 40 kg/m 2 + 0.6 kPa of the live load, live load - 1.5 kPa or floor point load of 1.8 kN Note: Not all sizes of SmartLam GL18 in this table are stocked in each state. Please check with your supplier before ordering. Floor load width (mm) 1200 1800 2400 3000 3600 4200 4800 5400 6000 6600 Member size DxB (mm) Floor mass (kg/m 2 ) Maximum Bearer span (mm) Continuous span 150x65 40 4050 3650 3150 2800 2550 2350 2200 2050 1950 1850 180x65 40 4600 4200 3750 3350 3050 2800 2650 2500 2350 2250 210x65 40 5150 4700 4350 3900 3550 3300 3050 2900 2750 2600 240x65 40 5700 5150 4800 4450 4050 3750 3500 3300 3100 5 2950 5 270x65 40 6200 5650 5250 4950 4600 4250 3950 5 3700 10 3500 15 3350 20 300x65 40 6700 6100 5650 5350 5100 47005 440015 410020 390025 370030 330x65 40 7200 6550 6100 5750 55005 510015 480020 450030 425035 405040 360x65 40 7650 6950 6500 6150 5850 10 5550 25 5150 30 4850 35 4600 40 4400 50 390x65 40 8100 7400 6900 65005 620020 595030 555035 525045 495050 470060 420x65 40 8550 7800 7250 6850 10 6550 25 6300 35 5950 45 5600 55 5300 60 5050 70 450x65 40 9000 8200 7650 725015 690030 665040 635055 595060 565070 535080 480x65 40 9450 8600 8000 5 7600 20 7250 35 6950 50 6700 60 6300 70 6000 80 5700 90 510x65 40 9850 9000 8400 10 7950 25 7550 40 7300 55 7050 70 6700 80 6300 95 6000 100 150x85 40 4300 3900 3600 3200 2900 2700 2500 2350 2250 2100 180x85 40 4900 4450 4150 3850 3500 3200 3000 2850 2700 2550 210x85 40 5500 5000 4650 4400 4050 3750 3500 3300 3100 2950 240x85 40 6050 5500 5150 4850 4600 4300 4000 3750 3550 3400 270x85 40 6600 6000 5600 5300 5050 4800 4500 4250 4000 3800 5 300x85 40 7150 6500 6050 5700 5450 5250 5000 47005 445010 425015 330x85 40 7650 6950 6500 6150 5850 5600 545010 515015 485020 460025 360x85 40 8150 7400 6900 6550 6250 6000 5 5800 15 5550 25 5250 30 5000 35 390x85 40 8600 7850 7350 6950 6600 6350 10 6150 20 5950 30 5650 35 5400 40 420x85 40 9100 8300 7750 7300 7000 5 6700 15 6500 25 6300 35 6050 45 5750 50 450x85 40 9550 8700 8150 7700 7350 10 7100 20 6850 30 6600 40 6450 50 6100 60 480x85 40 10000 9150 8550 8100 770015 740025 715035 695045 675060 650070 510x85 40 10450 9550 8900 84505 805020 775030 750040 725055 705065 685075 540x85 40 10850 9950 9300 8800 10 8400 25 8100 35 7800 45 7600 60 7350 70 7200 85 570x85 40 11300 10350 9650 9150 15 8750 30 8400 40 8150 55 7900 65 7650 80 7500 95 NOTES: D = member depth, B = member breadth, NS = not suitable. The above table was based on a maximum DL of 40 (kg/m 2 ), floor live load of 1.5 (kPa), floor point load of 1.8 (kN). End bearing lengths = 42 mm at end supports and 58 mm at internal supports for continuous members.Subscript values indicate the minimum additional bearing length where required to be greater than 42 mm at end supports and 58 mm at internal supports. Restraint value for slenderness calculations is 600 mm. (floor joist centres at 600 mm max) Not all sizes of SmartLam GL18 in this table are stocked in each state. Please check with your supplier before ordering SmartLam G18C Design Guide 15
- Page 1: SmartLam GL18 Design Guide A BOND A
- Page 4 and 5: TABLE OF CONTENTS INTRODUCTION 1 TE
- Page 6 and 7: Design loads Duration of load/servi
- Page 8 and 9: Pre - Camber in mm based upon cambe
- Page 10 and 11: MULTIPLE SmartLam GL18 SECTION BEAM
- Page 12 and 13: SmartLam DURABILITY and WEATHER EXP
- Page 14 and 15: CHECKING IN SmartLam GLULAM (Cont
- Page 16 and 17: DETERMINATION OF ROOF LOAD WIDTH RO
- Page 20 and 21: FLOOR BEARERS SUPPORTING SINGLE STO
- Page 22 and 23: SINGLE SPAN LINTELS IN SINGLE/UPPER
- Page 24 and 25: SINGLE SPAN LINTELS IN LOWER STOREY
- Page 26 and 27: SINGLE/CONTINUOUS SPAN ROOF RAFTER
- Page 28 and 29: SINGLE/CONTINUOUS SPAN ROOF RAFTER
- Page 30 and 31: SINGLE/CONTINUOUS SPAN ROOF RAFTER
- Page 32 and 33: SINGLE/CONTINUOUS SPAN ROOF RAFTER
- Page 34 and 35: Roof load width (mm) 1800 3000 4200
- Page 36 and 37: CONTINUOUS SPAN VERANDAH BEAM AS 40
- Page 38 and 39: CONTINUOUS SPAN VERANDAH BEAM AS 40
- Page 40 and 41: HANGING BEAM SUPPORTING CEILING LOA
- Page 42 and 43: COUNTER BEAM SUPPORTING HANGING BEA
- Page 44 and 45: STRUTTING BEAM SUPPORTING UNDERPURL
- Page 46 and 47: STRUTTING/COUNTER BEAM SUPPORTING U
- Page 48 and 49: Roof Strut Roof Area Supported 'X'
- Page 50: SmartFrame TOOLS SmartFrame Softwar
CONTINUOUS SPAN FLOOR BEARERS SUPPORTING FLOOR<br />
LOADS ONLY<br />
Floor mass - 40 kg/m 2<br />
Loadings: Permanent - self weight + 40 kg/m 2 + 0.6 kPa of the live load, live load - 1.5 kPa or floor point load of 1.8 kN<br />
Note: Not all sizes of <strong>SmartLam</strong> GL18 in this table are stocked in each state. Please check with your supplier before ordering.<br />
Floor load width (mm) 1200 1800 2400 3000 3600 4200 4800 5400 6000 6600<br />
Member size<br />
DxB (mm)<br />
Floor mass<br />
(kg/m 2 )<br />
Maximum Bearer span (mm)<br />
Continuous span<br />
150x65 40 4050 3650 3150 2800 2550 2350 2200 2050 1950 1850<br />
180x65 40 4600 4200 3750 3350 3050 2800 2650 2500 2350 2250<br />
210x65 40 5150 4700 4350 3900 3550 3300 3050 2900 2750 2600<br />
240x65 40 5700 5150 4800 4450 4050 3750 3500 3300 3100 5 2950 5<br />
270x65 40 6200 5650 5250 4950 4600 4250 3950 5 3700 10 3500 15 3350 20<br />
300x65 40 6700 6100 5650 5350 5100 47005 440015 410020 390025 370030<br />
330x65 40 7200 6550 6100 5750 55005 510015 480020 450030 425035 405040<br />
360x65 40 7650 6950 6500 6150 5850 10 5550 25 5150 30 4850 35 4600 40 4400 50<br />
390x65 40 8100 7400 6900 65005 620020 595030 555035 525045 495050 470060<br />
420x65 40 8550 7800 7250 6850 10 6550 25 6300 35 5950 45 5600 55 5300 60 5050 70<br />
450x65 40 9000 8200 7650 725015 690030 665040 635055 595060 565070 535080<br />
480x65 40 9450 8600 8000 5 7600 20 7250 35 6950 50 6700 60 6300 70 6000 80 5700 90<br />
510x65 40 9850 9000 8400 10 7950 25 7550 40 7300 55 7050 70 6700 80 6300 95 6000 100<br />
150x85 40 4300 3900 3600 3200 2900 2700 2500 2350 2250 2100<br />
180x85 40 4900 4450 4150 3850 3500 3200 3000 2850 2700 2550<br />
210x85 40 5500 5000 4650 4400 4050 3750 3500 3300 3100 2950<br />
240x85 40 6050 5500 5150 4850 4600 4300 4000 3750 3550 3400<br />
270x85 40 6600 6000 5600 5300 5050 4800 4500 4250 4000 3800 5<br />
300x85 40 7150 6500 6050 5700 5450 5250 5000 47005 445010 425015<br />
330x85 40 7650 6950 6500 6150 5850 5600 545010 515015 485020 460025<br />
360x85 40 8150 7400 6900 6550 6250 6000 5 5800 15 5550 25 5250 30 5000 35<br />
390x85 40 8600 7850 7350 6950 6600 6350 10 6150 20 5950 30 5650 35 5400 40<br />
420x85 40 9100 8300 7750 7300 7000 5 6700 15 6500 25 6300 35 6050 45 5750 50<br />
450x85 40 9550 8700 8150 7700 7350 10 7100 20 6850 30 6600 40 6450 50 6100 60<br />
480x85 40 10000 9150 8550 8100 770015 740025 715035 695045 675060 650070<br />
510x85 40 10450 9550 8900 84505 805020 775030 750040 725055 705065 685075<br />
540x85 40 10850 9950 9300 8800 10 8400 25 8100 35 7800 45 7600 60 7350 70 7200 85<br />
570x85 40 11300 10350 9650 9150 15 8750 30 8400 40 8150 55 7900 65 7650 80 7500 95<br />
NOTES:<br />
D = member depth, B = member breadth, NS = not suitable.<br />
The above table was based on a maximum DL of 40 (kg/m 2 ), floor live load of 1.5 (kPa), floor point load of 1.8 (kN).<br />
End bearing lengths = 42 mm at end supports and 58 mm at internal supports for continuous members.Subscript values indicate the minimum additional<br />
bearing length where required to be greater than 42 mm at end supports and 58 mm at internal supports.<br />
Restraint value for slenderness calculations is 600 mm. (floor joist centres at 600 mm max)<br />
Not all sizes of <strong>SmartLam</strong> GL18 in this table are stocked in each state. Please check with your supplier before ordering<br />
<strong>SmartLam</strong> G18C Design Guide 15
Change language