Rotary Seals - Dilanda.it
Rotary Seals - Dilanda.it
Rotary Seals - Dilanda.it
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Turcon ® Roto Variseal ®<br />
Table LXV Standard Turcon ® materials for Roto Variseal ®<br />
Material,<br />
Applications,<br />
Properties<br />
Code<br />
Spring<br />
material<br />
Code<br />
Operating temp.<br />
°C<br />
Mating surface<br />
material<br />
MPa<br />
max.<br />
Turcon ® T40<br />
For all lubricating and non-lubricating<br />
hydraulic fluids, water hydraulics, soft mating<br />
surfaces<br />
Carbon fibre filled<br />
Colour: Grey<br />
T40<br />
Spring material<br />
AISI 301<br />
S -100 to +260<br />
Steel<br />
Steel, chromeplated<br />
Cast iron<br />
Stainless steel,<br />
Aluminium<br />
Bronze<br />
Alloys<br />
15<br />
Turcon ® T78<br />
For all lubricated and non-lubricated<br />
applications, soft mating surfaces.<br />
Aromatic polymer<br />
Colour: Tan to dark brown<br />
T78<br />
Spring material<br />
AISI 301<br />
S -100 to +260<br />
Steel<br />
Steel, chromeplated<br />
Cast iron<br />
Stainless steel<br />
5<br />
n Highlighted materials are standard.<br />
Busak+Shamban recommends that the following surface<br />
finishes be observed :<br />
Table LXVI<br />
Surface roughness<br />
Recommended maximum surface roughness μm<br />
Media Shaft surface 1) Static groove surface<br />
Cryogenic and low molecular gases<br />
Hydrogen, Helium, Freon, Oxygen<br />
N<strong>it</strong>rogen<br />
Low viscos<strong>it</strong>y fluids<br />
Water, Alcohols, Hydrazine, Gaseous<br />
n<strong>it</strong>rogen, Natural gas, Skydrol, air<br />
High viscos<strong>it</strong>y fluids<br />
Hydraulic oils, Crude oil, Gear oil,<br />
Sealants, Glue, Milkproducts<br />
R max = 1.0 μm<br />
R z = 0.63 μm<br />
R a = 0.1 μm<br />
R max = 2.5 μm<br />
R z = 1.6 μm<br />
R a = 0.2 μm<br />
R max = 2.5 μm<br />
R z = 1.6 μm<br />
R a = 0.2 μm<br />
R max = 3.5 μm<br />
R z = 2.2 μm<br />
R a = 0.3 μm<br />
R max = 5.0 μm<br />
R z = 3.5 μm<br />
R a = 0.6 μm<br />
R max = 6.5 μm<br />
R z = 5.0 μm<br />
R a = 0.8 μm<br />
1) The sealing surface must be free from spiral grooves.<br />
The material contact area R mr should be approx. 50 to 70%, determined at a cut depth c = 0.25 x R z , relative to a reference line of C ref . 5%.<br />
208<br />
Latest information available at www.busakshamban.com<br />
Ed<strong>it</strong>ion April 2006