Silane cross-linked polyethylene pipe INTERSOL ... - Watts Industries
Silane cross-linked polyethylene pipe INTERSOL ... - Watts Industries Silane cross-linked polyethylene pipe INTERSOL ... - Watts Industries
SILANE CROSS-LINKED POLYETHYLENE PIPE Table 17 is compiled from literature data and gives a detailed survey of typical values for certain characteristics compared to those of INTERSOL ® PEX-b 18 Table 17 Property Standard Unit PEX-a INTERSOL ® PEX-b PEX-c PP-R PB Specific gravity DIN 53479 G/cm 3 0,94 0,95 0,94 0,90 0,93 Ultimate tensile strength DIN 53455 N/mm 2 26-30 22-27 22-25 40 33 Elongation DIN 53455 % 350-550 350-550 350-450 800 300 Tensile modulus of elasticity (20°) DIN 53457 N/mm 2 >550 >550 >550 >800 >350 Coefficient of linear expansion (20°C) - °C 1,4.10-4 1,4.10-4 1,4.10-4 1,5.10-4 1,5.10-4 Thermal conductivity - °C 2,0.10-4 2,0.10-4 2,0.10-4 - - Coefficient of linear expansion (20-100°C) - W/mk 0,38 0,35-0,41 0,35 0,24 0,23 Degree of cross-linking DIN 16892 % >75 >65 >60 - - The descriptions and photographs contained in this product specification sheet are supplied by way of information only and are not binding. Watts Industries reserves the right to carry out any technical and design improvements to its products without prior notice.
SILANE CROSS-LINKED POLYETHYLENE PIPE WARRANTY FOR CROSS-LINKED POLYETHYLENE (PEX) PIPE FOR HOT FLUID PRESSURE PIPING 19 TUBO INTERSOL ® The pipe is produced within a certified quality management system in accordance with UNI EN ISO 9001:2000. The INTERSOL ® pipe is produced using top quality raw materials and a high technology production cycle. Product quality is guaranteed by strict control plans in every phase of the transformation, from the raw materials to the process to the finished product. In addition, all coils produced are subject to a final hydraulic test. The specific tests for the INTERSOL ® , pipe, performed in-house, comply with sector regulations that vary based on the country for which the pipe is intended (for example UNI 9338/9349 - DIN 16892/16893 - DIN 4726/4729 - NFT 54085 - UNE 53381). As a result, Watts Industries Italia S.r.l. warrants the INTERSOL ® pipe as indicated below : 1) INTERSOL ® pipes will be replaced free of charge up to 10 years after the date of supply if damage is caused by manufacturing defects (note: “Manufacturer's warranty provided based on technical experience in product obsolescence”) 2) damage to third parties due to manufacturing defects in the INTERSOL ® pipe based on current provisions of law (Presidential Decree 224 of May 24, 1988), will be indemnified through insurance coverage pursuant to product liability policy VO 100008604 from Winterthur Assicurazioni. There is a single maximum coverage per claim per year, of €453,780.00. Points 1) and 2) above will be valid provided the following conditions are met : a) The INTERSOL ® dpipe must be stored, handled and installed according to the instructions reported in our technical specifications b) Operating conditions (pressure and temperature) must comply with the limits reported in our technical specifications c) The product must bear our fully intact identification mark. The customer must provide the following information when requesting warranty service : - place and date of installation - the pipe's identifying data and mark - information on conditions of pipe installation and operation (temperature and pressure) - sample on which the breakage occurred (preferably at least 1 meter long with the break in the middle) Watts Industries Italia S.r.l. reserves the right to examine the cause of the break on site before initiating the warranty procedures. A Division of Watts Water Technologies Inc.
- Page 1 and 2: Silane cross-linked polyethylene pi
- Page 3 and 4: SILANE CROSS-LINKED POLYETHYLENE PI
- Page 5 and 6: SILANE CROSS-LINKED POLYETHYLENE PI
- Page 7 and 8: SILANE CROSS-LINKED POLYETHYLENE PI
- Page 9 and 10: SILANE CROSS-LINKED POLYETHYLENE PI
- Page 11 and 12: SILANE CROSS-LINKED POLYETHYLENE PI
- Page 13 and 14: SILANE CROSS-LINKED POLYETHYLENE PI
- Page 15 and 16: SILANE CROSS-LINKED POLYETHYLENE PI
- Page 17: SILANE CROSS-LINKED POLYETHYLENE PI
SILANE CROSS-LINKED POLYETHYLENE PIPE<br />
WARRANTY FOR CROSS-LINKED POLYETHYLENE (PEX)<br />
PIPE FOR HOT FLUID PRESSURE PIPING<br />
19<br />
TUBO <strong>INTERSOL</strong> ®<br />
The <strong>pipe</strong> is produced within a certified quality management system in accordance with UNI EN<br />
ISO 9001:2000. The <strong>INTERSOL</strong> ® <strong>pipe</strong> is produced using top quality raw materials and a high<br />
technology production cycle.<br />
Product quality is guaranteed by strict control plans in every phase of the transformation, from<br />
the raw materials to the process to the finished product. In addition, all coils produced are<br />
subject to a final hydraulic test.<br />
The specific tests for the <strong>INTERSOL</strong> ® , <strong>pipe</strong>, performed in-house, comply with sector<br />
regulations that vary based on the country for which the <strong>pipe</strong> is intended (for example UNI<br />
9338/9349 - DIN 16892/16893 - DIN 4726/4729 - NFT 54085 - UNE 53381).<br />
As a result, <strong>Watts</strong> <strong>Industries</strong> Italia S.r.l. warrants the <strong>INTERSOL</strong> ® <strong>pipe</strong> as indicated below :<br />
1) <strong>INTERSOL</strong> ® <strong>pipe</strong>s will be replaced free of charge up to 10 years after the date of supply if<br />
damage is caused by manufacturing defects (note: “Manufacturer's warranty provided<br />
based on technical experience in product obsolescence”)<br />
2) damage to third parties due to manufacturing defects in the <strong>INTERSOL</strong> ® <strong>pipe</strong> based on<br />
current provisions of law (Presidential Decree 224 of May 24, 1988), will be indemnified<br />
through insurance coverage pursuant to product liability policy VO 100008604 from<br />
Winterthur Assicurazioni.<br />
There is a single maximum coverage per claim per year, of €453,780.00.<br />
Points 1) and 2) above will be valid provided the following conditions are met :<br />
a) The <strong>INTERSOL</strong> ® d<strong>pipe</strong> must be stored, handled and installed according to the instructions<br />
reported in our technical specifications<br />
b) Operating conditions (pressure and temperature) must comply with the limits reported in our<br />
technical specifications<br />
c) The product must bear our fully intact identification mark.<br />
The customer must provide the following information when requesting warranty service :<br />
- place and date of installation<br />
- the <strong>pipe</strong>'s identifying data and mark<br />
- information on conditions of <strong>pipe</strong> installation and operation (temperature and pressure)<br />
- sample on which the breakage occurred (preferably at least 1 meter long with the break in<br />
the middle)<br />
<strong>Watts</strong> <strong>Industries</strong> Italia S.r.l. reserves the right to examine the cause of the break on site before<br />
initiating the warranty procedures.<br />
A Division of <strong>Watts</strong> Water Technologies Inc.
Change language