Master Thesis - OUFTI-1

More documents

Recommendations

Info

This support is mounted on the face −X. This conguration is possible thanks to the restricted dimensions of the support (as shown in Figure 2.8). Figure 2.8: Conguration and dimensions of the antenna support Indeed, as already mentioned, the CubeSat standard requires that the access port area will not be obstructed. However, in our case, the only port which would be obstructed is the port used for the MHX transceiver (as shown in Figure 2.9). And, as it was already mentioned, OUFTI-1 does not use this function of the FM 430. So, there is no problem to put the antenna support at this place. Figure 2.9: Description of the port obstructed by the antenna support The xing method is the same as for the solar panels. The support will be glued on the skeleton using epoxy Stycast 2850 (with catalyst 24 LV). 2.3.4 Permanent magnet and hysteretic bars To maintain the attitude of OUFTI-1, a control system is needed. This one is managed by the Attitude Determination and Control System (ADCS) subsystem [25]. 27
In our case, because of the limited available power and the fact that the payloads do not require a precise attitude control, it was decided to use a passive control system. This system comprises one permanent magnet, with dimensions of 20 × 4 × 4 mm, made of AlNiCo 5 (an Aluminum-Nickel-Cobalt alloy) and four hysteretic bars, with dimensions of 80 × 1 × 1 mm, made of P ermenorm 5000 H2. The principle is the following one: the permanent magnet tends to align its magnetization axis with the local Earth's magnetic eld (as shown in Figure 2.10). The hysteretic bars allow to limit, by hysteretic damping, the rotation rate of the satellite to an acceptable value (which will have to be determined by tests). Figure 2.10: Principle of the OUFTI-1 ADCS subsystem [25] Last year, a solution with only two hysteretic bars was implemented (the conguration is available in Figure 2.11). Figure 2.11: Last year's conguration of the ADCS 28
Page 1 and 2: University of Liège Faculty of App
Page 3 and 4: Abstract OUFTI-1, standing for "Orb
Page 5 and 6: 3.4 Initial idea . . . . . . . . .
Page 7 and 8: List of Figures 1.1 The Pumpkin's C
Page 9 and 10: 4.18 MAC matrix using the simple me
Page 11 and 12: List of Acronyms ADCS Al AlNiCo ASI
Page 13 and 14: Thesis outline This thesis focuses
Page 15 and 16: of larger satellites. So, the CubeS
Page 17 and 18: 1.2 OUFTI-1 project 1.2.1 Genesis O
Page 19 and 20: • XatCobeo (Vigo - Spain): Develo
Page 21 and 22: Chapter 2 OUFTI-1: Flight system co
Page 23 and 24: Figure 2.2: Product tree of OUFTI-1
Page 25 and 26: 2.3.2 Solar panels The armor panels
Page 27: • We do not want to drill or manu
Page 31 and 32: Figure 2.13: Magnetic eld obtained
Page 33 and 34: Figure 2.17: Pictures of the ADCS c
Page 35 and 36: consider the possibility of oshorin
Page 37 and 38: Figure 2.20: Exploded view of OUFTI
Page 39 and 40: I xx , I yy and I zz are called the
Page 41 and 42: Subsystem: Structure & Conguration
Page 43 and 44: Subsystem: Thermal Control Parts Co
Page 45 and 46: Chapter 3 Design of a new support f
Page 47 and 48: Figure 3.3: Batteries during and af
Page 49 and 50: The concept is the following one: F
Page 51 and 52: A test under vacuum conditions was
Page 53 and 54: Thermal Expansion (CTE) of the mate
Page 55 and 56: Figure 3.9: Classication by density
Page 57 and 58: The last property to determine is t
Page 59 and 60: • So, it was decided to use two t
Page 61 and 62: is to prevent the batteries' bulge.
Page 63 and 64: • Then, the thermostats, that wil
Page 65 and 66: Figure 3.23: Schematics of the cove
Page 67 and 68: • Other components, including the
Page 69 and 70: 3.9.3 Dynamic behavior Finally, it
Page 71 and 72: 3.10 Summary Through this chapter,
Page 73 and 74: Chapter 4 Electronic cards dynamic
Page 75 and 76: Figure 4.1: Example of manufacturin
Page 77 and 78: Figure 4.4: Illustration of the exp
Page 79 and 80:
Figure 4.5: MAC between the two mod
Page 81 and 82:
• Global mass/stiness smearing me
Page 83 and 84:
4.2.6 Modeling of the chassis A gen
Page 85 and 86:
Q = ω k = 1 ω b − ω a 2 ζ ⇒
Page 87 and 88:
Their study was based on the fact t
Page 89 and 90:
Figure 4.14: Example of spacecraft
Page 91 and 92:
Figure 4.15: Location of measuremen
Page 93 and 94:
Figure 4.18: MAC matrix using the s
Page 95 and 96:
4.3.6 Application of the local mass
Page 97 and 98:
ρ P C 104 connector = 10.12 × 10
Page 99 and 100:
According to this particular shape,
Page 101 and 102:
This is due to the fact that this c
Page 103 and 104:
environment. Then, this model is ex
Page 105 and 106:
5.2.4 Antenna support For the anten
Page 107 and 108:
Components Young's moduli (GP a) Po
Page 109 and 110:
Components Young's moduli (GP a) Po
Page 111 and 112:
5.3 Static analysis As described in
Page 113 and 114:
Figure 5.9: Illustration of the com
Page 115 and 116:
Figure 5.11: Maximal Von Mises stre
Page 117 and 118:
Figure 5.12: First mode of OUFTI-1
Page 119 and 120:
Figure 5.15: Precise PSD of Vega [5
Page 121 and 122:
Chapter 6 Conclusions This master t
Page 123 and 124:
provided for each method used. We h
Page 125 and 126:
last versions of the Verication Con
Page 127 and 128:
[13] Ph. LEDENT. "Design and Implem
Page 129 and 130:
[40] "Dejond - Aluminum Catalog ".
Page 131 and 132:
Appendix A Schemas of solar panels
Page 133 and 134:
Appendix B Schemas of electronic ca
Page 135 and 136:
Appendix C Fixations of the endless
Page 137 and 138:
Appendix D Datasheet of the battery
show all

Master Thesis - OUFTI-1

Create successful ePaper yourself

Delete template?

Save as template?