ZXP Series 7 User's Manual (en) - Hant

More documents

Recommendations

Info

E: Smart Card Options Contact Smart Cards Contact Smart Cards have a pad of contacts on the surface of the card that connect to the circuitry embedded into the card. The printer responds to commands that position the card at the contact location, where the printer connects to the contacts on the Smart Card. Data to be encoded onto the Smart Card, and data read from the Smart Card, can interface via a connector on the printer’s rear panel (External Contact Station), or encoding/decoding can be performed by logic on the printer’s Main PCBA (Contact Encoder). All other printer operations remain the same as the standard models. Card Loading Orientation for Contact Smart Cards Place the cards in the Feeder Cartridge in the correct orientation as shown (with the goldplated Smart Card contacts at the top of the card and facing to the right). Ensure that the cards are seated properly the hopper. 174 Zebra ZXP Series 7 Card Printer User’s Manual P1036101-001
E: Smart Card Options External Contact Station Interface When a command to the printer interface sends a card to the External Contact Station, the printer connects the External Contact Station to the female DB-9 connector on the rear of the printer. DB-9 Connector location for External Contact Station An attached external Smart Card Programmer can be used to program Smart Card chips. The following table shows the Smart Card Contact Points. DB-9 Pin Connections Pin Smart Card Contact Points Pin Smart Card Contact Points 1 C1 (VCC) 6 C6 (Vpp) 2 C2 (Reset) 7 C7 (I/O) 3 C3 (Clock) 8 C8 (RFU) 4 C4 (RFU) (GND when chip 9 5 C5 (GND) is at station) P1036101-001 Zebra ZXP Series 7 Card Printer User’s Manual 175
Page 1 and 2:
ZEBRA ZXP SERIES 7 User’s Manual
Page 3 and 4:
Contents 1 • Introduction . . . .
Page 5 and 6:
1 Introduction Description This Man
Page 7 and 8:
1: Introduction Icons Icons Through
Page 9 and 10:
2 Installation and Setup General In
Page 11 and 12:
2: Installation and Setup Unpacking
Page 13 and 14:
2: Installation and Setup Unpacking
Page 15 and 16:
2: Installation and Setup Loading C
Page 17 and 18:
Installing the Dual Cleaning Cartri
Page 19 and 20:
Installing the Manual Feed Cleaning
Page 21 and 22:
2: Installation and Setup Loading a
Page 23 and 24:
2: Installation and Setup Loading a
Page 25 and 26:
2: Installation and Setup Loading t
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
2: Installation and Setup Connectin
Page 39 and 40:
2: Installation and Setup Connectin
Page 41 and 42:
2: Installation and Setup Installin
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
3 Operation Introduction Printing w
Page 55 and 56:
3: Operation Manual Card Feed Manua
Page 57 and 58:
3: Operation Operator Control Panel
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
4 Printer Settings and Adjustments
Page 69 and 70:
4: Printer Settings and Adjustments
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
5 ZXP Series Toolbox Introduction I
Page 99 and 100:
5: ZXP Series Toolbox Information I
Page 101 and 102:
5: ZXP Series Toolbox Information M
Page 103 and 104:
5: ZXP Series Toolbox Configuration
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
5: ZXP Series Toolbox Cleaning Clea
Page 113 and 114:
5: ZXP Series Toolbox Technology Te
Page 115 and 116:
5: ZXP Series Toolbox Technology Sm
Page 117 and 118:
5: ZXP Series Toolbox Advanced Secu
Page 119 and 120:
5: ZXP Series Toolbox Advanced Secu
Page 121 and 122:
6 Cleaning Caution • PROTECT YOUR
Page 123 and 124:
6: Cleaning Cleaning the Printer Cl
Page 125 and 126:
6: Cleaning Cleaning the Printer Po
Page 127 and 128: 6: Cleaning Cleaning the Laminator
Page 133 and 134: 6: Cleaning Dual Cleaning Cartridge
Page 135 and 136: 7 Troubleshooting Introduction The
Page 137 and 138: 7: Troubleshooting Introduction COD
Page 143 and 144: 7: Troubleshooting Ethernet Etherne
Page 145 and 146: 8 Technical Specifications Standard
Page 147 and 148: 8: Technical Specifications Specifi
Page 149 and 150: 8: Technical Specifications Specifi
Page 151 and 152: 8: Technical Specifications Agency
Page 153 and 154: 8: Technical Specifications Declara
Page 155 and 156: APPENDIX A Printer Configurations I
Page 157 and 158: Appendix B Connecting to a Network
Page 159 and 160: B: Connecting to a Network Setting
Page 161 and 162: B: Connecting to a Network Step 13.
Page 163 and 164: B: Connecting to a Network Printer
Page 165 and 166: Appendix C Accessing a Network Prin
Page 167 and 168: C: Accessing a Network Printer via
Page 169 and 170: Appendix D Magnetic Card Encoder In
Page 171 and 172: D: Magnetic Card Encoder Printing O
Page 173 and 174: D: Magnetic Card Encoder Functional
Page 175 and 176: D: Magnetic Card Encoder AAMVA The
Page 177: APPENDIX E Smart Card Options Intro
Page 181 and 182: APPENDIX F Worldwide Support For Te
Page 183 and 184: F: Worldwide Support Asia Pacific -
show all

ZXP Series 7 User's Manual (en) - Hant

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?