ZXP Series 7 User's Manual (en) - Hant

More documents

Recommendations

Info

2: Installation and Setup Loading Cards Loading Cards Caution • DO NOT bend cards or touch print surfaces as this can reduce print quality. The surface of the cards must remain clean and dust free. Always store cards in an enclosed container. Ideally, use cards as soon as possible. Step 1. Step 2. Remove the wrapping from the card stack. Holding the card stack by the sides (do not touch the print surfaces), hold it vertically against a flat surface such as a desktop. If the stack is too thick for your hand to hold it comfortably, use about half a stack at a time. Step 3. Push the stack back and forth to an angle of about 45° from vertical, so as to separate all of the cards. Note • Static charges and edge burrs from the card die-cutting process can render individual cards stuck together with significant adhesion force. These cards must be physically separated from each other before inserting into the feeder; if not separated, feeding or printing problems may occur. Step 4. Restore the card stack to its original squared-off condition. 10 Zebra ZXP Series 7 Card Printer User’s Manual P1036101-001
2: Installation and Setup Loading Cards Step 5. Open the Feeder Cartridge Door, and slide the Card Stack Pusher all the way to the right, until it locks in place. Step 6. Place the card stack in the Feeder Cartridge in the correct orientation shown below. Step 7. For optimum performance, ensure that the cards are fully seated; then close the Feeder Cartridge Door. P1036101-001 Zebra ZXP Series 7 Card Printer User’s Manual 11
Page 1 and 2: ZEBRA ZXP SERIES 7 User’s Manual
Page 3 and 4: Contents 1 • Introduction . . . .
Page 5 and 6: 1 Introduction Description This Man
Page 7 and 8: 1: Introduction Icons Icons Through
Page 9 and 10: 2 Installation and Setup General In
Page 11 and 12: 2: Installation and Setup Unpacking
Page 13: 2: Installation and Setup Unpacking
Page 17 and 18: Installing the Dual Cleaning Cartri
Page 19 and 20: Installing the Manual Feed Cleaning
Page 21 and 22: 2: Installation and Setup Loading a
Page 23 and 24: 2: Installation and Setup Loading a
Page 25 and 26: 2: Installation and Setup Loading t
Page 37 and 38: 2: Installation and Setup Connectin
Page 39 and 40: 2: Installation and Setup Connectin
Page 41 and 42: 2: Installation and Setup Installin
Page 53 and 54: 3 Operation Introduction Printing w
Page 55 and 56: 3: Operation Manual Card Feed Manua
Page 57 and 58: 3: Operation Operator Control Panel
Page 65 and 66:
3: Operation Operator Control Panel
Page 67 and 68:
4 Printer Settings and Adjustments
Page 69 and 70:
4: Printer Settings and Adjustments
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
5 ZXP Series Toolbox Introduction I
Page 99 and 100:
5: ZXP Series Toolbox Information I
Page 101 and 102:
5: ZXP Series Toolbox Information M
Page 103 and 104:
5: ZXP Series Toolbox Configuration
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
5: ZXP Series Toolbox Cleaning Clea
Page 113 and 114:
5: ZXP Series Toolbox Technology Te
Page 115 and 116:
5: ZXP Series Toolbox Technology Sm
Page 117 and 118:
5: ZXP Series Toolbox Advanced Secu
Page 119 and 120:
5: ZXP Series Toolbox Advanced Secu
Page 121 and 122:
6 Cleaning Caution • PROTECT YOUR
Page 123 and 124:
6: Cleaning Cleaning the Printer Cl
Page 125 and 126:
6: Cleaning Cleaning the Printer Po
Page 127 and 128:
6: Cleaning Cleaning the Laminator
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
6: Cleaning Dual Cleaning Cartridge
Page 135 and 136:
7 Troubleshooting Introduction The
Page 137 and 138:
7: Troubleshooting Introduction COD
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
7: Troubleshooting Ethernet Etherne
Page 145 and 146:
8 Technical Specifications Standard
Page 147 and 148:
8: Technical Specifications Specifi
Page 149 and 150:
8: Technical Specifications Specifi
Page 151 and 152:
8: Technical Specifications Agency
Page 153 and 154:
8: Technical Specifications Declara
Page 155 and 156:
APPENDIX A Printer Configurations I
Page 157 and 158:
Appendix B Connecting to a Network
Page 159 and 160:
B: Connecting to a Network Setting
Page 161 and 162:
B: Connecting to a Network Step 13.
Page 163 and 164:
B: Connecting to a Network Printer
Page 165 and 166:
Appendix C Accessing a Network Prin
Page 167 and 168:
C: Accessing a Network Printer via
Page 169 and 170:
Appendix D Magnetic Card Encoder In
Page 171 and 172:
D: Magnetic Card Encoder Printing O
Page 173 and 174:
D: Magnetic Card Encoder Functional
Page 175 and 176:
D: Magnetic Card Encoder AAMVA The
Page 177 and 178:
APPENDIX E Smart Card Options Intro
Page 179 and 180:
E: Smart Card Options External Cont
Page 181 and 182:
APPENDIX F Worldwide Support For Te
Page 183 and 184:
F: Worldwide Support Asia Pacific -
show all

ZXP Series 7 User's Manual (en) - Hant

Create successful ePaper yourself

Delete template?

Save as template?